Installation Guide Home Network System Repeater Model No. KX-HNH200 KX-HNZ108 By installing this unit, you can extend the range of your Home Network System to include areas where reception was previously not available. The unit extends the range in all directions, allowing several floors to be covered. Important:
R This unit is an accessory unit for use with a Panasonic Home Network System. R You must register this unit with your hub before it can be used. For U.S. users For assistance, please contact us at 1-800-272-7033 or visit our Web site:
http://shop.panasonic.com/support for customers in the U.S.A. Please register your product: http://shop.panasonic.com/support For Canada users For assistance, please visit our support page on:
http://panasonic.ca/english/support http://panasonic.ca/french/support Printed in China HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 1 2016/04/26 13:54:34 Table of Contents Introduction Accessory information ...............3 Important Information Graphical symbols for use on equipment and their descriptions ...............................4 For your safety ...........................5 Important safety instructions ......6 For best performance ................7 Other information .......................8 Setup Control .....................................10 Installation/Registering the range repeater to the hub ..................12 Appendix Wall mounting ..........................14 Troubleshooting .......................15 Specifications ..........................16 FCC and other information (for U.S. users only) .......................17 Customer services (for U.S. users only) .........................................19 Limited Warranty (ONLY FOR U.S.A.) .....................................20 Other notices and information (for Canada) ...................................22 Warranty (for Canada users only) .........................................23 2 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 2 2016/04/26 13:54:34 Accessory information Supplied accessories No. A Accessory item/Part number AC adaptor/PQLV219Y Introduction Quantity 1 Other information R Design and specifications are subject to change without notice. R The illustrations in these instructions may vary slightly from the actual product. 3 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 3 2016/04/26 13:54:34 Important Information Graphical symbols for use on equipment and their descriptions Symbol Explanation Symbol Explanation Alternating current
(A.C.) Direct current (D.C.) Class P equipment
(equipment in which protection against electric shock relies on Double Insulation or Reinforced Insulation) ON (power) Protective earth OFF (power) Protective bonding earth Functional earth For indoor use only Stand-by (power) ON/OFF (power;
push-push) Caution, risk of electric shock 4 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 4 2016/04/26 13:54:34 For your safety To prevent severe injury and loss of life/property, read this section carefully before using the product to ensure proper and safe operation of your product. WARNING Power connection R Use only the power source marked on the product. R Do not overload power outlets and extension cords. This can result in the risk of fire or electric shock. R Completely insert the AC adaptor/power plug into the power outlet. Failure to do so may cause electric shock and/
or excessive heat resulting in a fire. R Regularly remove any dust, etc. from the AC adaptor/power plug by pulling it from the power outlet, then wiping with a dry cloth. Accumulated dust may cause an insulation defect from moisture, etc. resulting in a fire. R Unplug the product from power outlets if it emits smoke, an abnormal smell, or makes an unusual noise. These conditions can cause fire or Important Information electric shock. Confirm that smoke has stopped emitting and contact us at http://
shop.panasonic.com/support R Unplug from power outlets and never touch the inside of the product if its casing has been broken open. R Never touch the plug with wet hands. Danger of electric shock exists. R Do not connect non-specified devices. Installation R To prevent the risk of fire or electrical shock, do not expose the product to rain or any type of moisture. R Do not place or use this product near automatically controlled devices such as automatic doors and fire alarms. Radio waves emitted from this product may cause such devices to malfunction resulting in an accident. R Do not allow the AC adaptor cord to be excessively pulled, bent or placed under heavy objects. Operating safeguards R Unplug the product from power outlets before cleaning. Do not use liquid or aerosol cleaners. 5 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 5 2016/04/26 13:54:34 Important safety instructions When using your product, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
1. Do not use this product near water for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement or near a swimming pool. 2. Use only the power cord indicated in this document. Important Information R Do not disassemble the product. Medical R Consult the manufacturer of any personal medical devices, such as pacemakers or hearing aids, to determine if they are adequately shielded from external RF (radio frequency) energy. (The product operates in the frequency range of 1.92 GHz to 1.93 GHz, and the RF transmission power is 115 mW
(max.).) R Do not use the product in health care facilities if any regulations posted in the area instruct you not to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy. CAUTION Installation and location R The AC adaptor is used as the main disconnect device. Ensure that the AC outlet is installed near the product and is easily accessible. 6 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 6 2016/04/26 13:54:34 Important Information R If the transmission quality is not satisfactory, move this product to another location. Placement R Install the unit within hub range in an indoor environment. We recommend installing the unit in a raised position (such as on a wall). R Avoid positioning the unit close to objects that will interfere with reception, such as thick walls, radiators, metal shelving, etc. R For maximum distance noise-free operation, place the unit away from electrical appliances such as TV, radio, personal computer, or other telephone equipment. R Keep an appropriate distance from the hub to maximize the range of your phone system. Find the appropriate location by indicator. If the checking the indicator lights red or amber, re-position this unit in a place For best performance Product location/avoiding noise This product and other compatible Panasonic devices use radio waves to communicate with each other. R For maximum coverage and noise-free communications, place this product:
at a convenient, high, and central location with no obstructions between this product and any connected devices in an indoor environment. away from electronic appliances such as TVs, radios, personal computers, wireless devices, or other phones. facing away from radio frequency transmitters, such as external antennas of mobile phone cell stations.
(Avoid putting this product on a bay window or near a window.) R Coverage and transmission quality depends on the local environmental conditions. 7 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 7 2016/04/26 13:54:34 Important Information where the green. indicator lights Environment R Keep the product away from electrical noise generating devices, such as fluorescent lamps and motors. R The product should be kept free from excessive smoke, dust, high temperature, and vibration. R The product should not be exposed to direct sunlight. R Do not place heavy objects on top of the product. R When you leave the product unused for a long period of time, unplug the product from the power outlet. R The product should be kept away from heat sources such as heaters, kitchen stoves, etc. It should not be placed in rooms where the temperature is less than 0 C (32 F) or greater than 40 C (104 F). Damp basements should also be avoided. R The maximum communication range may be shortened when the product is used in the following places: Near obstacles such as hills, tunnels, underground, near metal objects such as wire fences, etc. R Operating the product near electrical appliances may cause interference. Move away from the electrical appliances. Other information Routine care R Wipe the outer surface of the product with a soft moist cloth. R Do not use benzine, thinner, or any abrasive powder. Notice for product disposal, transfer, or return R This product can store your private/confidential information. To protect your privacy/
confidentiality, we recommend that you erase information such as phonebook or caller list entries from the memory before you dispose of, transfer, or return the product. 8 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 8 2016/04/26 13:54:34 HubHandsetRepeaterRepeater rangeHub range Notice Important Information 9 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 9 2016/04/26 13:54:34 Setup Control STATUS indicator indicator ID indicator M N Understanding the STATUS indicator and Indicator STATUS indicator Light status Green On Meaning R Within hub range. The unit is ready for use. indicator R 1 handset is communicating with the hub through this unit. R 2 handsets are communicating with the hub through this unit. R Out of hub range R The unit is in registration mode. R The power is off. (AC adaptor is not connected properly.) Flashing Flashing rapidly On Flashing Red Off 10 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 10 2016/04/26 13:54:34 BAC Indicator indicator Light status Green Amber Red Off On On On Setup Meaning R Signal strength of the hub is strong. R Signal strength of the hub is weak. R Out of hub range. R The unit is not being used. R The power is off. 11 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 11 2016/04/26 13:54:34 Setup Installation/Registering the range repeater to the hub Once the unit is connected to a power outlet in step 3, it automatically goes into registration mode (if not already registered). 1 Range repeater: Connect the AC adaptor. R Use only the supplied Panasonic AC adaptor PQLV219. 2 Hub: Press and hold M OTHER DEVICEN for about 5 seconds. R Depending on the hub, a registration tone sounds. R If all registered handsets start ringing, press the same button to stop. Then repeat this step. R The next step must be completed within 90 seconds. 3 Range repeater: Connect the AC adaptor to a power outlet. R When the unit is turned on, the STATUS indicator and indicator light amber for about 2 seconds. 4 Range repeater: Confirm that the STATUS indicator and indicator light green. (The unit is ready for use.) R If the indicators do not light green, re-position the unit in a place where the indicators light green. 5 Hub: To exit registration mode, press M 12 OTHER DEVICEN. HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 12 2016/04/26 13:54:34 Press plug firmly.Hook(120 V AC, 60 Hz) Setup Note:
R The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) R The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected. R The unit can support a maximum of 2 handsets at a time. R Up to 2 range repeaters can be registered to the hub. 13 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 13 2016/04/26 13:54:34 Appendix Wall mounting Drive the screws (not supplied) into the wall. Mount the unit, then slide it down. Note:
R Make sure that the wall is strong enough to support the weight of the unit. 14 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 14 2016/04/26 13:54:34 Troubleshooting Problem The unit does not work. While talking using the handset, sound cuts in and out. Appendix Cause/solution R When the indicators do not light, the AC adaptor is not connected properly. Check the connections. R When the indicators do not light green, move the unit closer to the hub. R Registration may have been canceled. Deregister the unit, then re-register. Deregister:
1 Unplug the AC adaptor, then press and hold M N. 2 While pressing and holding N, re-connect the AC M adaptor. 3 Keep pressing and holding N for about 10 seconds M until STATUS indicator flashes amber. Then release M Re-register: Unplug the AC adaptor, then perform from step 2, Installation/Registering the range repeater to the hub,page 12. R The handsets is out of range. N. Move the handset closer to this unit. 15 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 15 2016/04/26 13:54:35 Appendix The STATUS indicator continues to light amber for a while. R M N was pressed. The unit is in programming modes. To exit, press M M the unit. N again. Do not press N, except when deregistering DECT (Digital Enhanced Cordless Telecommunications) Specifications R Standard R Frequency range 1.92 GHz 1.93 GHz R RF transmission power 115 mW (max.) R Power source 120 V AC, 60 Hz R Power consumption R Operating conditions Standby: Approx. 1.0 W, Maximum: Approx. 1.8 W 0 C 40 C (32 F 104 F), 20 % 80 % relative air humidity (dry) 16 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 16 2016/04/26 13:54:35 FCC and other information (for U.S. users only) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this device. CAUTION:
Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this device. NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This Appendix equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Some devices operate at frequencies that may cause interference to nearby TVs and VCRs. To minimize or prevent such interference, this device should not be placed near or on 17 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 17 2016/04/26 13:54:35 Appendix top of a TV or VCR. If interference is experienced, move this device further away from the TV or VCR. This will often reduce or eliminate interference. FCC RF Exposure Warning:
R This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. R To comply with FCC RF exposure requirements, the device must be installed and operated 20 cm (8 inches) or more between the product and all persons body. R This product may not be collocated or operated in conjunction with any other antenna or transmitter. R For body-worn operation, the device must be used only with a non-metallic accessory. Use of other accessories may not ensure compliance with FCC RF exposure requirements. Notice:
R FCC ID can be found on the rear of the unit. 18 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 18 2016/04/26 13:54:35 Customer services (for U.S. users only) Appendix 19 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 19 2016/04/26 13:54:35 You may also contact us directly at: 1-800-272-7033,Monday - Friday 9 am to 9 pm; Saturday - Sunday 10 am to 7 pm, EST.Accessories!hp://shop.panasonic.com/supportCustomer Services DirectoryShopfor all your Panasonic gearGo to Get everything you need to get the most out ofyour Panasonic products Accessories & Parts for your Camera, Phone, A/V products, TV, Computers & Networking, Personal Care, Home Appliances, Headphones, Baeries, Backup Chargers & moreFor Product Informaon, Operang Assistance, Parts, Owners Manuals, Dealer and Service infogo to hp://shop.panasonic.com/supportFor the hearing or speech impaired TTY: 1- 877-833-8855 As of June 2015 Appendix Limited Warranty (ONLY FOR U.S.A.) 20 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 20 2016/04/26 13:54:35 Limited Warranty Coverage (For USA Only)LaborOne (1) YearPartsOne (1) YearTo submit a new repair request and for quick repair status visit our Web Site athttp://shop.panasonic.com/supportPanasonic Products Limited WarrantyOnline Repair RequestMail-In Service--Online Repair RequestIf your product does not work properly because of a defect in materials or workmanship, Panasonic Corporation of North America (referred to as the warrantor) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (warranty period), at its option either (a) repair your product with new or refurbished parts,(b) replace it with a new or a refurbished equivalent value product, or (c) refund your purchase price. The decision to repair, replace or refund will be made by the warrantor.During the Labor warranty period there will be no charge for labor. During the Parts warranty period, there will be no charge for parts. This Limited Warranty excludes both parts and labor for non-rechargeable batteries, antennas, and cosmetic parts (cabinet). This warranty only applies to products purchased and serviced in the United States.This warranty is extended only to the original purchaser of a new product which was not sold as is.Home Network System ProductsmicroSD card (Included model only)90 days N/AWhen shipping the unit, carefully pack, include all supplied accessories listed in the Owners Manual, and send it prepaid, adequately insured and packed well in a carton box. When shipping Lithium Ion batteries please visit our Web Site at http://shop.panasonic.com/support as Panasonic is committed to providing the most up to date information. Include a letter detailing the complaint, a return address and provide a daytime phone number where you can be reached. A valid registered receipt is required under the Limited Warranty.IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE PURCHASER WILL BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.Product or Part Name Appendix 21 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 21 2016/04/26 13:54:35 Limited Warranty Limits and Exclusions(As examples, this excludes damages for lost time, travel to and from the servicer, loss of or damage to media or images, data or other memory or recorded content. The items listed are not exclusive, but for illustration only.)This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, introduction of sand, humidity or liquids, commercial use such as hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than a Factory Service Center or other Authorized Servicer, or damage that is attributable to acts of God.THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER LIMITED WARRANTY COVERAGE.THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY.ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOUR RESPONSIBILITY.Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the exclusions may not apply to you.This warranty gives you specific legal rights and you may also have other rights which vary from state to state. If a problem with this product develops during or after the warranty period, you may contact your dealer or Service Center. If the problem is not handled to your satisfaction, then write to: Consumer Affairs Department Panasonic Corporation of North America 661 Independence Pkwy Chesapeake, VA 23320As of June 2015 Appendix Other notices and information (for Canada) 22 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 22 2016/04/26 13:54:35 NOTICE:This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.RF Exposure Warning:R This product complies with ISED radiation exposure limits set forth for an uncontrolled environment.R To comply with ISED RF exposure requirements, the hub must be installed and operated 20 cm (8 inches) or more between product and all persons body.R This product may not be collocated or operated in conjunction with any other antenna or transmitter. Warranty (for Canada users only) Appendix 23 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 23 2016/04/26 13:54:35 Dry cell batteries are also excluded from coverage under this warranty. Rechargeable batteries are warranted for ninety (90) days from date of original purchase.This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by Panasonic Canada Inc., or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper maintenance, improper batteries, power line surge, lightning damage, modification, introduction of sand, humidity or liquids, commercial use such as hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than a Authorized Servicer, or damage that is attributable to acts of God. THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY. (As examples, this warranty excludes damages for lost time, travel to and from the Authorized Servicer, loss of or damage to media or images, data or other memory or recorded content. This list of items is not exhaustive, but for illustration only.)Home Network System Products One (1) yearmicroSD card (Included model only) One (1) yearPanasonic Canada Inc.5770 Ambler Drive, Mississauga, Ontario L4W 2T3PANASONIC PRODUCT - LIMITED WARRANTYPanasonic Canada Inc. warrants this product to be free from defects in material and workmanship under normal use and for a period as stated below from the date of original purchase agrees to, at its option either (a) repair your product with new or refurbished parts, (b) replace it with a new or a refurbished equivalent value product, or (c) refund your purchase price. The decision to repair, replace or refund will be made by Panasonic Canada Inc. This warranty is given only to the original purchaser, or the person for whom it was purchased as a gift, of a Panasonic brand product mentioned above sold by an authorized Panasonic dealer in Canada and purchased and used in Canada, which product was not sold as is, and which product was delivered to you in new condition in the original packaging. IN ORDER TO BE ELIGIBLE TO RECEIVE WARRANTY SERVICE HEREUNDER, A PURCHASE RECEIPT OR OTHER PROOF OF DATE OF ORIGINAL PURCHASE, SHOWING AMOUNT PAID AND PLACE OF PURCHASE IS REQUIRED LIMITATIONS AND EXCLUSIONSEXCHANGE PROGRAM Appendix 24 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 24 2016/04/26 13:54:35 www.panasonic.ca/english/supportIn certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the exclusion of implied warranties, so the above limitations and exclusions may not be applicable. This warranty gives you specific legal rights and you may have other rights which vary depending on your province or territory. For product information and operation assistance, please visit our Support page:CONTACT INFORMATIONFor defective product exchange within the warranty period, please contact the original dealer. Notes 25 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 25 2016/04/26 13:54:35 Notes 26 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 26 2016/04/26 13:54:35 Notes 27 HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 27 2016/04/26 13:54:35 For your future reference We recommend keeping a record of the following information to assist with any repair under warranty. Serial No.
(found on the rear of the unit) Name and address of dealer Date of purchase Attach your purchase receipt here. HNH200_for_US_en-CA_(en_en)_0426_ver.003.pdf 28 2016/04/26 13:54:35 Two Riverfront Plaza, Newark, NJ 07102-5490 Panasonic System Networks Co., Ltd. 20165770 Ambler Drive, Mississauga, Ontario L4W 2T3