WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6392232.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Toyota Trailer Camera ECU Model: TA-220-TUND-MI FCC ID: ACJ932A-TA220 IC : 216A-TA220 PANASONIC AUTOMOTIVE Panasonic Automotive Systems Company of America W-LAN receiver and camera system User Manual Version 1.0 10/28/2022 Author Sanjeev Rao Toyota Trailer Camera ECU Model: TA-220-TUND-MI FCC ID: ACJ932A-TA220 IC : 216A-TA220 Table of Contents INTRODUCTION GETTING STARTED WITH W-LAN RECEIVER W-LAN RECEIVER OPERATION SYSTEM SETTINGS PAIRING OF W-LAN RECEIVER WITH CAMERA Toyota Trailer Camera ECU Model: TA-220-TUND-MI FCC ID: ACJ932A-TA220 IC : 216A-TA220 PRIVACY WARNING The W-LAN receiver video camera module is built into this WCS but no video is recorded or stored in the system. Toyota Trailer Camera ECU Model: TA-220-TUND-MI FCC ID: ACJ932A-TA220 IC : 216A-TA220 FCC/ISED Regulatory Notices Modification Statement Panasonic Automotive Systems of America has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user's authority to operate the equipment. Panasonic Automotive Systems of America n'approuve aucune modification apportee a l'appareil par l'utilisateur, quelle qu'en soit la nature. Tout changement ou modification peuvent annuler le droit d'uti/isation de l'appareil par l'utilisateur. Interference statement This device complies with Part 15 of the FCC Rules and ISEDs licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The antenna should be installed and operated with minimum distance of 20 cm between the radiator and your body. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. L 'antenne doit etre installee de fafon a garder une distance minimale de 20 centimetres entre la source de rayonnements et votre corps. Radiation Exposure Statement:
This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis plus de 20cm entre le radiateur et votre corps. Toyota Trailer Camera ECU Model: TA-220-TUND-MI FCC ID: ACJ932A-TA220 IC : 216A-TA220 FCC Class B digital device notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. CAN ICES-3 (B) / NMB-3 (B) This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numerique de classe B est conforme a la norme canadienne ICES-003. Professional installation instruction 1. Installation personal This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting. 2. Installation location The product shall be installed at a location where the radiating antenna can be kept 20cm from nearby person in normal operation condition to meet regulatory RF exposure requirement. 3. External antenna Use only the antennas which have been approved by the applicant. The non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC/IC limit and is prohibited. 4. Installation procedure Please refer to users manual for the detail. 5. Warning Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty. Instructions d'installation professionnelle 1. Installation Ce produit est destine a un usage specifique et doit etre installe par un personnel qualifie maitrisant les radiofrequences et les regles s'y rapportant. L'installation et les reglages ne doivent pas etre modifies par l'utilisateur final. 2. Emplacement d'installation En usage normal, afin de respecter les exigences reglementaires concernant l'exposition aux radiofrequences, ce produit doit etre installe de facon a respecter une distance de 20cm entre l'antenne emettrice et les personnes. 3. Antenn externe. Utiliser uniiquement les antennes approuvees par le fabricant. L'utilisation d'autres antennes peut conduire a un niveau de rayonnement essentiel ou non essentiel depassant les niveaux limites definis par FCC/IC, ce qui est interdit. 4. Procedure d'installation Consulter le manuel d'utilisation. 5. Avertissement Choisir avec soin la position d'installation et s'assurer que la puissance de sortie ne depasse pas les limites en vigueur. La violation de cette regle peut conduire a de serieuses penalites federales. Toyota Trailer Camera ECU Model: TA-220-TUND-MI FCC ID: ACJ932A-TA220 IC : 216A-TA220 Introduction W-LAN receiver is a part of Wireless Camera System (WCS) which includes wireless camera, display and a W-LAN receiver. The camera streams video over W-LAN to the multiple display in the vehicle via the W-LAN receiver. The wireless camera will come paired with the system from the manufacturer. The user will have the ability to add remove cameras (see WCS Pairing). Video can be streamed consciously or on-
demand on each display. DETACHABLE ANTENNA USAGE This radio transmitter [IC: 216A-TA220] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Le prsent metteur radio [IC: 216A-TA220] a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'metteur. Wireless Camera System Diagram Toyota Trailer Camera ECU Model: TA-220-TUND-MI FCC ID: ACJ932A-TA220 IC : 216A-TA220 W-LAN receiver Electrical specification:
Operational voltage Operational current Operational frequency Operational power consumption W Lan transmit power BTLE transmit power Storage Temperature Operating temperature 802.11g sensitivity 54Mbps BT receiver sensitivity 9 V - 16 V 0.65 A 2.4 GHz W-LAN and BT 9 Watt 29.94 dBm 18 dBm
-40 deg C to + 85 deg C
-30 deg C to +70 deg C
-74 dBm
-80 dBm GETTING STARTED WITH WIRELESS CAMERA SYSTEM 1. Make sure camera battery is fully charged before using camera with W_LAN receiver 2. Wake up wireless camera by Plugging the USB-C cable to wireless camera and computer USB port 3. Power on W-LAN receiver by suppling 12V via power harness. 4. The wireless camera status indicator should come on after a few seconds. 5. Wait for the wireless camera status indicator to become solid green, indicating video is streaming. 6. Press AUX (
) on the display window to display wireless camera video on the main display.
) on the main display window to show the same wireless camera video on the second 7. Press (
display Press t(
Turn off 12V to turn receiver off. 8. 9.
) to change video from wireless camera to wired video Toyota Trailer Camera ECU Model: TA-220-TUND-MI FCC ID: ACJ932A-TA220 IC : 216A-TA220 WIRELESS CAMERA SYSTEM OPERATION 1. Waking up the Wireless Camera To conserve battery the wireless camera will be in sleep state when shipped from factory. To wake the camera, you may perform one of the following actions:
Supply 12V Connect a USB-C cable to a USB power 2. Main display and operation a. Turn on receiver by applying 12V b. Press (
) to access the wireless camera video. Toyota Trailer Camera ECU Model: TA-220-TUND-MI FCC ID: ACJ932A-TA220 IC : 216A-TA220 c. Press to enter settings menu, select "Camera Device Management". d. To connect to a previously paired camera select the camera to view Connect button and press the Connect button on the screen. f. After the camera connected to the W-LAN receiver you will see the camera stream on the multimedia display. 3. Second display operation a. Wired camera view Only Mode (default) Wired camera is always displayed on the second display in this mode. Toyota Trailer Camera ECU Model: TA-220-TUND-MI FCC ID: ACJ932A-TA220 IC : 216A-TA220 b. AUTO Mode In AUTO mode, if the left or right turn signals are engaged the wireless camera video is shown on the second display. If turn signal is off, then wired camera video is displayed on the second display. This feature helps in conserving the wireless camera battery when it is not connected to the 12V vehicle power supply by switching the video to cargo and turning off the video streaming in the wireless camera. c. ON Mode Wireless camera video is always displayed on the second display in this mode. Toyota Trailer Camera ECU Model: TA-220-TUND-MI FCC ID: ACJ932A-TA220 IC : 216A-TA220 WIRELESS CAMERA SYSTEM SETTINGS Wireless camera settings allow flipping an image, pairing more wireless cameras, run diagnostics, reset settings, and perform software updates. 1. Turn receiver on 2. Press the Aux (
) button in the screen to see wireless camera landing page. 1. 3. Wireless camera setting menu is only accessible while vehicle is parked. Select icon from the main display. 4. To exit the wireless camera settings, select icon. 5. Wireless Camera Settings Menu Camera Device Management Camera Device Management menu lists all currently paired wireless cameras to the system and allows you to add/delete/turn off your wireless cameras. Diagnostics Provides you with wireless camera and W-LAN receiver (WiFi Receiver) diagnostics. Reset Settings restores the factory default settings. Second display will be set up (default) ON mode Second display will be set up (default) wired camera view Flip WiFi Camera Image option will be set to (default) ON Toyota Trailer Camera ECU Model: TA-220-TUND-MI FCC ID: ACJ932A-TA220 IC : 216A-TA220 Delete all paired wireless cameras Flip Image This is a toggle button to flip the camera image vertically. WIRELESS CAMERA PAIRING 1. Enter to wireless CAM screen. 2. Press to enter settings menu, select "Camera Device Management", and click Add Camera. 2. The main display shows below message. Toyota Trailer Camera ECU Model: TA-220-TUND-MI FCC ID: ACJ932A-TA220 IC : 216A-TA220 3. Move the Trailer CAM following the sequence below in order to put the camera in pairing mode. 1) In lens up position for 5 seconds 2) In lens down position for 5 seconds 3) In lens up position again Once the wireless CAM enters Pairing mode, the wireless CAM LED willblinking orange 4. Select "OK" button and QR code will be shown on the radio display. 5. Aim thewireless CAM to the radio display to scan the QR code. 6. Once QR code scan and pairing is completed, "Wireless Camera was added successfully"
will be displayed. Toyota Trailer Camera ECU Model: TA-220-TUND-MI FCC ID: ACJ932A-TA220 IC : 216A-TA220 If QR scan or pairing failed, a failed message is displayed. Please try previous steps 7. again.