Compliance statement and notification For U.S.A FCC CAUTION Changes or modifications no expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the FCC Note:
following two conditions: (1) This device may not cause harmful interference, and (2) This equipment has been tested and found to comply with the limits for a Class A digital this device must accept any interference received, including interference that may device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-
cause undesired operation. able protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. For Canada CAN ICES-3(A)/NMB-3(A) 1 For U.S.A.
<FCC Information>
Information to to Be Supplied to the End User by the Installer or Integrator If the FCC ID of this module is not visible from the outside of the end product, to satisfy FCC exterior labeling requirements, the end product must be labeled in a visible area with the fol-
lowing: Contains FCC ID: ACJ9TAWJ-VR3004 The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating an adapter in compliance with local regulations. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Operating near 2.4 GHz electrical appliances may cause interference. Move away from the electrical appliances. Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. This device is master equipment, 5.15-5.25GHz, 5.58-5.66GHz band is restricted to indoor operations only. Frequency Tolerance: 50 ppm (2.4GHz band), 20 ppm (5GHz band) Radio Frequency (RF) Exposure Warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled en-
vironment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body (excluding extremities: hands, wrists, feet and ankles). body. MEDICAL:
Consult the manufacturer of any personal medical devices, such as pacemakers, to determine if they are adequately shielded from external RF (radio frequency) energy. The unit operates in the frequency range of 2.412 GHz to 2.462 GHz and/or 5.180 GHz to 5.85 GHz. Do not use the unit in health care facilities if any regulations posted in the area instruct you not to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF (radio frequency) energy. 2 For Canada
<IC Information>
Information to to Be Supplied to the End User by the Installer or Integrator If the IC ID of this module is not visible from the outside of the end product, to satisfy IC exte-
rior labeling requirements, the end product must be labeled in a visible area with the following:
Contains IC: 216A-WJVR3004 The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating an adapter in compliance with local regulations. Informations fournir lutilisateur final par linstallateur ou lintgrateur Afin de satisfaire les exigences en matire dtiquetage externe IC, si lidentification IC de ce module nest pas visible sur le produit final, celui-ci doit tre muni dune tiquette appose dans une zone visible avec les indications suivantes : Contient IC : 216A-WJVR3004 Les consignes de contrle et de scurit suivantes doivent tre publies dans la documenta-
tion fournie lutilisateur final du produit ou du systme intgrant un adaptateur conform-
ment aux rglements locaux. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired opera-
tion of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that neces-
sary for successful communication. Conformment la rglementation dIndustrie Canada, le prsent metteur radio peut fonctionner avec une antenne dun type et dun gain maximal (ou infrieur) approuv pour lmetteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolec-
trique lintention des autres utilisateurs, il faut choisir le type dantenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas lintensit nces-
saire ltablissement dune communication satisfaisante. 3 For Canada
<IC Information>
5.15-5.25GHz band is restricted to indoor operations only. La bande 5 150-5 250 MHz est restreints une utilisation lintrieur. Radio Frequency (RF) Exposure Warning This equipment complies with IC radiation exposure limits set forth for an uncontrolled en-
vironment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equip-
ment should be installed and operated keeping the radiator at least 20cm or more away from persons body (excluding extremities: hands, wrists, feet and ankles). Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolec-
triques (RF) CNR-102 de lIC. Cet quipement doit tre install et utilis en gardant une dis-
tance de 20 cm ou plus entre le dispositif rayonnant et le corps ( lexception des extrmits :
mains, poignets, pieds et chevilles). corps. body. Panasonic System Networks Co., Ltd. 2014 PaF0514-0 PGQW1597ZA Printed in Japan Imprime au Japon