FCC ID: ACJ-V2WA Wireless Module

Wireless Module Panasonic PIOT-V2(WA) User Manual Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the publisher. Pentium is trademark of Intel. All copyright reserved. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/CANADA 1 Integration instructions for host product manufacturers Applicable FCC rules to module FCC Part 15.247 Summarize the specific operational use conditions The module is must be installed in mobile device. This device is intended only for OEM integrators under the following conditions:

1) 2) 3) The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Limited module procedures Not applicable Trace antenna designs Not applicable RF exposure considerations 20 cm separation distance and co-located issue shall be met as mentioned in Summarize the specific operational use conditions. Product manufacturer shall provide below text in end-product manual This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Antennas WNC WNC Brand name Model name Antenna type Antenna gain Antenna connector ANT-0 ANT-1 Printed Printed 2.66 1.28 NA NA Label and Compliance Information Product manufacturers need to provide a physical or e-label stating 2 Contains FCC ID: ACJ-V2WA with finished product Information on Test Modes and Additional Testing Requirements Test tool: RTK UI_mptool.exe, version: 1V3 shall be used to set the module to transmit continuously. Additional Testing, Part 15 Subpart B Disclaimer The module is only FCC authorized for the specific rule parts listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed 3 Industry Canada statement:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference

(2) This device must accept any interference, including interference that may cause undesired operation of the device Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) Lappareil ne doit pas produire de brouillage;

(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Radiation Exposure Statement:

This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:

Cet quipement est conforme Canada limites d'exposition aux radiations dans un environnement non contrl. Cet quipement doit tre install et utilis distance minimum de 20cm entre le radiateur et votre corps. 4 This device is intended only for OEM integrators under the following conditions:

1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 condition above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes:

1) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 1 condition ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. IMPORTANT NOTE:

In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product

(including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:

Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling 5 The final end product must be labeled in a visible area with the following: Contains IC:216A-V2WA. Plaque signaltique du produit final

"Contient des IC: 216A-V2WA". Manual Information to the End User Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante:

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which The end user manual shall include all required regulatory information/warning as show in integrates this module. this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. This radio transmitter [IC: 216A-V2WA] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Le prsent metteur radio [IC: 216A-V2WA] a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'metteur. Antennas Brand name Model name Antenna type Antenna gain Antenna connector WNC WNC ANT-0 ANT-1 Printed Printed 2.66 1.28 NA NA 6 Taiwan

CCAFXXLPXXXXTX) 7 1. Introduction Thank you for purchasing the 802.11 b/g/n Wireless LAN module that provides the easiest way to wireless networking. This User Manual contains detailed instructions in the operation of this product. Please keep this manual for future reference. System Requirements

- 128 MB of RAM or later (recommended)

- 300 MHz processor or higher 2. Driver/Utility Installation The driver should have been installed before the Appliances is shipped from the manufacturer. You can start using its network function without installing driver or utility. This module is associated product for Appliances host. The following description provides a basic installation for wireless module. For more information about the Wireless Module, please refer to your manual. Installing Wi-Fi module :

1. Link cable with connector on wireless module 2. Link wireless module with connector to PC and install software in wireless module 3. Open the back lid of Appliances, lock wireless module on internal main board of Appliances. 4. Power supply on internal main-board and allow Appliances to load fully. 3. Connecting to an Existing Network 1. Use the remote control that came with your Appliances to access the network configuration 2. Select the scanning wireless network function. The system starts to scan for available network. On this list, click Refresh to refresh the list at any time settings page. 3. Select the network you want to connect to. 8 4. If the chosen network has security enabled, you will have to setup corresponding security parameter. Contact the network manager for the correct settings. Select the security type and fill in required parameters. The options include the following:

WPA/WPA2/CCKM WPA/WPA2 Passphrase 802.1x Pre-Shared Key (Static WEP) None 9 4. Modifying a Wireless Network 4.1 Modifying General Settings 1. Use the remote control that came with your Appliances to access the network configuration settings page. 2. From the profile list, select one profile and choose the modify function. 3. Modify the settings below for your network. Profile Name Identifies the configuration wireless network profile. This name must be unique. Profile names are not case sensitive. Client Name Identifies the client machine. Use this profile for Configures station to operate in Access Point mode. Access Point mode Network Names The IEEE 802.11 wireless network name. This field

(SSIDs) has a maximum limit of 32 characters. Configure up to three SSIDs (SSID1, SSID2, and SSID3). 10 4.2 Modifying Security Settings 1. Use the remote control that came with your Appliances to access the network configuration settings page. 2. Select a security option of this wireless network. This product provides security options below. Contact your wireless network administrator for choosing a correct option. WPA/WPA2/CCKM WPA/WPA2 Passphrase 802.1x Pre-Shared Key (Static WEP) None WPA/WPA2 Enables the use of Wi-Fi Protected Access (WPA). Choosing WPA/WPA2 opens the WPA/WPA2 EAP drop-down menu. The options include:

EAP-FAST EAP-TLS EAP-TTLS EAP-SIM PEAP (EAP-GTC) PEAP (EAP-MSCHAP V2) LEAP Enables WPA/WPA2 Passphrase security. Click on the Configure button and fill in the WPA/WPA2 Passphrase. Enables 802.1x security. This option requires IT administration. Choosing 802.1x opens the 802.1x EAP type drop-down menu. The options include:

EAP-FAST EAP-TLS EAP-TTLS EAP-SIM PEAP (EAP-GTC) PEAP (EAP-MSCHAP V2) LEAP Enables the use of pre-shared keys that are defined on both the access point and the station. To define pre-shared encryption keys, choose the Pre-Shared Key radio button and click the Configure button to fill in the Define Pre-Shared Keys window. WPA/WPA2 Passphrase 802.1x Pre-Shared Key

(Static WEP) 11 None Allow Association to Mixed Cells Limit Time for Finding Domain Controller To Group Policy Delay No security (not recommended). Check this check box if the access point with which the client adapter is to associate has WEP set to Optional and WEP is enabled on the client adapter. Otherwise, the client is unable to establish a connection with the access point. Check this check box and enter the number of seconds (up to 300) after which the authentication process times out when trying to find the domain controller. Entering zero is like unchecking this check box, which means no time limit is imposed for finding the domain controller. Note: The authentication process times out whenever the authentication timer times out or the time for finding the domain controller is reached. Specify how much time elapses before the Windows logon process starts group policy. Group policy is a Windows feature used by administrators to specify configuration options for groups of users. The objective is to delay the start of Group Policy until wireless network authentication occurs. Valid ranges are from 0 to 65535 seconds. The value that you set goes into effect after you reboot your computer with this profile set as the active profile. This drop-down menu is active only if you chose EAP-based authentication. 12 5. Specifications Main chipset TX/RX Frequency range Item Content RTL8720CM-VH2 1TX/1RX 2.400 ~ 2.4835 GHz Channel spacing 5MHz for Wi-Fi, 2MHz for Bluetooth Modulation technology OFDM :BPSK,QPSK,16QAM,64QAM DSSS : CCK,DQPSK,DBPSK GFSK 802.11b: 11/5.5/2/1Mbps 802.11g: 54/48/36/24/18/12/9/6Mbps 802.11n: MCS0~MCS7(65Mbps) Data Rate Host interface Operation voltage Operation temperature Antenna Type Antenna peak gain 802.15.1:

UART DC 5V (1A, 5W)

-10o ~ 70oC Printed Antenna ANT0 : 2.66dBi ANT1 : 1.28dBi 13

= WLAN: >PET<

= Q00BsBEESsB9 BLE:

000BSBEE88BB Model : PIOT-V2(WA) C Made in China Panasonic Corporation SSSR FCC ID:ACJ-V2WA IC:216A-V2WA O48DNSK31 . SGCopess 2020.08.28[G)- ron zo rmeO O 0 l@ 7190 Oreic 6 5220) O17 1 OBE S066 POF = 33s O J

++/010.2

34567879:;<=>49948=

?@A@BC@DEFGHGH

MTUVWMXGHXIHHG

I@J@DKLMNBBOPQAKRQNPSMNBBQSSQNP VORYNDQZKRQNPKPJ[RKPJKDJS?Q\QSQNP

]^_aKbLKPJcQLLSdNKJ MNLOBCQKFc?GEH^ef[V

[OCg@ARh aDQiQPKLcNJOLKDVjjDN\KLkNDUKPKSNPQAlmImXnLO@RNNRYcNJOL@

opj@?@SQiPKRQNPUmaoXWGqlVrOPJ@DIMMm?hVMsXWGlV

INDmPSRKLLKRQNPtQRYQPUKPKSNPQAVjjLQKPA@S

oNtYNBQRBKpANPA@DPh

uvwxyvzw{|wz}~wvww

[QPA@D@LpF

n@PnNRDNS cKPKi@Dd@iOLKRNDpMNBjLQKPA@ UKPKSNPQAMNDjNDKRQNPNkNDRYVB@DQAK

RF_734_02 04 April 16 Modular Approval Request FCC (KDB 996369 D01 & Part 15.212) FCC ID: ACJ-V2WA Items to be covered by Single modular transmitters. 1. The modular transmitter must have its own RF shielding. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. 3. The modular transmitter must have its own power supply regulation. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(b)(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. 6. The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number in accordance with 15.212 (a)(1)(vi)(A) / (B). 8. there are very strict operational and 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 1.1310, 2.1091, 2.1093, and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance. Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Answer from applicant The modular has a shielding Case. Please refer to EUT Photo. The component number is RTL8720CM-VH2 The component number is RT9078-18GQZ_DFN4P /

RT8096CHGJ5 No antenna connector is used. And no external amplifier will be used with this modular. This modular is tested under stand-alone configuration. Please refer to Test setup photo. The modular transmitter is labeled with its own FCC ID number. Please refer to label sample and label location. The modular complies with this requirement. Please refer to user manual. The device complies with this requirement. Please refer to RF exposure report. RF_734_02 04 April 16 Answer from applicant Items to be covered by Split modular transmitters. 1. The modular transmitter must comply with all requirements of a single modular transmitter except for items (1) & (5) of the above single modular approval requirements. 2. Only the radio front end must be shielded. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The interface between the split sections of the modular system must be digital with a minimum signalling amplitude of 150 mV peak-to-peak. 3. Control information and other data may be exchanged between the transmitter control elements and radio front end. 4. The sections of a split modular transmitter must be tested installed in a host device(s) similar to that which is representative of the platform(s) intended for use. 5. Manufacturers must ensure that only transmitter control elements and radio front end components that have been approved together are capable of operating together. The transmitter module must not operate unless it has verified that the installed transmitter control elements and radio front end have been authorized together. Manufacturers may use means including, but not limited to, coding in hardware and electronic signatures in software to meet these requirements, and must describe the methods in their application for equipment authorization. Note: A limited modular approval (LMA) may be granted for single or split modular transmitters that comply partially with the requirements above. Name and surname of applicant (or authorized representative): __________________ Date: ___03 December 2020____ Signature: ___________________________

Ben Botros Manager - Regulatory Compliance Panasonic Corporation of North America Agent Authorization Letter November 19, 2020 Federal Communications Commission CHPAVC-20-F002 Authorization and Standards Division 7435 Oakland Mills Road Columbia, MD 21046 USA. Subject: Original Modular Approval for Panasonic WIFI-Bluetooth Module Type Designation PIOT-V2(WA) under FCC ID: ACJ-V2WA For Installation within Panasonic Appliances To whom it may concern:

Please be notified that Ben Botros of Panasonic Corporation of North America (PNA) , hereby authorize Mr. Gary Chang of Intemational Certification Corp, Taiwan (ROC) to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by International Certification Corp. on our behalf shall have the same effect as acts of our own. The undersigned hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing International Certification Corp. as our agent, we still recognize that we are responsible to a) comply with the relevant provisions of the certification program;

b) _ make alll necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including intemal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

c) __ make claims regarding certification only in respect of the scope for which certification has been granted;

4) donot use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

f) _use certification only to indicate the products are certified as being in conformity with specified standards;

2) _ endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

i) keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

Panasonic Corporation of North America Two Riverfront Plaza, Newark, NJ 07102-5490 TellFax: 201-348-7760 / Ben Botros@us panasonic.com Panasonic Ben Botros Manager - Regulatory Compliance Panasonic Corporation of North America

) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

Kk) document the actions taken. This authorization is for Single Modular, PIOT-V2(WA) under FCC ID: ACJ-V2WA and is valid for a om riod from the date of this letter. Thank you for your attention in this matter. Sincerely, bfhf Ben Botros Manager Regulatory & Compliance Panasonic Corporation of North America

Ben Botros Manager - Regulatory Compliance Panasonic Corporation of North America Request for Permanent & Short-Term Confidentiality November 19, 2020 Federal Communications Commission CHPAVC-20-F002 Authorization and Standards Division 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: Original Modular Approval for Panasonic WIFI-Bluetooth Module Type Designation PIOT-V2(WA) under FCC ID: ACI-V2WA For Installation within Panasonic Appliances To whom it may concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as permanent confidential document from public disclosure.

(@_Theory of Operation (2) Block Diagram _(3) Schematics Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmfal to our company and would give competitor an unfair advantage in the market. In addition, please be advised that Panasonic Corporation of North America hereby requests the following filed sensitive information to be held under short-term confidential, pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions Rules and the provisions in FCC Public DA 04-1705. We request temporarily confidentiality of 180 days, starting from the original issued Certification grant date.

@ External and Internal Photographs _(2) Operating Instructions (Users Manual)

(3) Test Setup Photographs Panasonic also acknowledges that we will provide appropriate notice to UL Japan should either of the following occur. Sincerely, AALS Ben Botros Manager Regulatory & Compliance Panasonic Corporation of North America Panasonic Corporation of North America Two Riverfront Plaza, Newark, NJ 07102-5490 TellFax: 201-348-7760 / Ben Botros@us panasonic.com