FCC ID: V5PQ58 Countertop Payment Terminal

Installation Manual Q58 Desktop Terminal Instruction Manual 1. Installation POWER port connects to the external power adapter. LINE port connects to telephone line(optional). RS232 port connects to serial port. LAN port connects to the network cable. USB (OTG) port connects to the USB disk or other devices, and for the terminal download. SAM card: Remove the cover at the bottom of the terminal. Insert the SAM card to the corresponding card slot. SIM card(optional): Insert the SIM card to the corresponding card slot. 2. Instructions 1Power ON/OFF Power onPress the ON/OFF button Power offPress the ON/OFF button clickYES , the terminal turns off successfully. for 2 seconds until the terminal turns on successfully. for 2 seconds, the Power OFF confirmation box appears, then 2Magnetic Stripe Card Put magnetic stripe side of magnetic card towards device interior, swipe the card with a steady speed during through magnetic reader slot. (Support bi-directional swiping) 3IC Card Put IC card chip side upward, push-in IC card slot and to bottom. 4Shred paper operating Instructions Make paper 45 degrees angle right to paper knife and shred paper. 5Tap contactless card. Put the contactless card into the area above the printer cover. 3. Installation and Usage Tips 1Avoid putting the terminal in direct sunlight, high temperature, moist, or dusty environment. 2Forbid non-professional to repair the terminal. 3Before insert the card, please check internal and around of IC card slot . when you found some suspicious objects , must report to related administrator. 4The terminal is without battery and can only be used on the desktop through the adapter, please be noted that it cannot be moved away from the desktop while using. 4. Password Entering Tips It is highly recommended to enter password as following ways:

1Set up peep shields. Enter password with shield by the structures of cashier desk;

2Place the POS terminal at an appropriate angle and make sure it is difficult to peer the password. For example, the POS was installed above the movable bracket;

3In enter password perspective, avoid surrounding video surveillance;

4Paste text instructions to remind the customers to shelter with body or palm when enter password. 5Merchants can also choose other ways to protect the customer input password. FCC Regulations This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1 ) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. ISED compliance statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) Lappareil ne doit pas produire de brouillage;

(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. FCC IDV5PQ58 IC ID11689A-Q58 RF Exposure Statement This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet metteur ne doit pas tre Co-plac ou ne fonctionnant en mme temps qu'aucune autre antenne oumetteur.Cet quipement devrait tre install et actionn avec une distance minimum de 20 centimtres entre leradiateur et votre corps. PAX Technology Limited Manufacturer: PAX Computer Technology (Shenzhen) Co. Ltd. Address: 4/F, No.3 Building, Software Park, Second Central Science-Tech Road,High-Tech Industrial Park, Shenzhen, Guangdong, China. Tel: +86 755 86169630 Website: www.pax.com.cn PAX continually invests to maintain its high quality products up to date with the latest certifications, therefore a comprehensive list can be requested via the website's contact form or on downloadable product brochures.

Note: 1. This would be a plastic label with a permanent adhesive. 2. The FCC label statement will include in the user manual which will print on a paper insert and sell with the device. label location

PAX Technology Limited Date: 8/24/2023 Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: CFR 47 2.911 (d)(5) Attestation FCC ID: V5PQ58 Grantee FRN: 0017536285 1. PAX Technology Limited certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. 2. PAX Technology Limited certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment and is not an affiliate or subsidiary of an entity identified on the Covered List. Sincerely yours, Company Name: PAX Technology Limited Contact Name: Jenna tan Title of Person: Certification Leader Address: Room 2416, 24/F., Sun Hung Kai Centre, 30 Harbour Road, Wanchai, Hong Kong, 518057, China

PAX Technology, Inc. 3680 Clear Channel Place Jacksonville, FL 32224

(877) 859-0099 Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Date: August 24, 2023 RE:

CFR 47 2.911 (d)(7) FCC US Agent Letter of Attestation Grantee Code: V5P Grantee FRN: 0017536285 To whom it may concern:

FCC US Agent Agent Company Name: Pax Technology, Inc. FCC FRN: 0033507476 Agent Contact Name: John Hallisey Agent US Address: 8775 Baypine Road, Jacksonville,FL 32256 Agent Email Address: John.Hallisey@pax.us This letter is to confirm that we have accepted the responsibility to act as US Agent on behalf of PAX Technology Limited for the above-referenced FCC Grantee Code. We are aware of the requirements and responsibilities of the applicants agent for service of process as outlined in the FCC section 2.911(d)(7) and Report and Order FCC 22-84 paragraph 63. Sincerely, Authorized Agent Contact Person Name: John Hallisey Agent contact Job Title: General Counsel Agent Company name: PAX Technology,Inc DocuSign Envelope ID: B0601BC3-D26F-4D08-BDD6-9282D716F3BC

PAX Technology Limited Date: 8/24/2023 Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: CFR 47 2.911 (d)(7) Agent Designation Attestation FCC ID: V5PQ58 Grantee FRN: 0017536285 PAX Technology Limited as required by section 2.911(d)(7), designates the following agent, located in the United States, for purposes of acting as the applicants agent for service of process. The applicant acknowledges that they will maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility under CFR 47 2.929(c) to inform the FCC whenever the agent information changes. U.S. Agent Information:

FRN: 0033507476 Contact Person: John Hallisey Company Name: Pax Technology,Inc. Company Address: 8775 Baypine Road,Jacksonville,FL 32256 Email: John.Hallisey@pax.us Sincerely yours, Company Name: PAX Technology Limited Contact Name: Jenna tan Title of Person: Certification Leader Address: Room 2416, 24/F., Sun Hung Kai Centre, 30 Harbour Road, Wanchai, Hong Kong, 518057, China

PAX Technology Limited DATE : 2023-08-24 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Request for Short-Term Confidentiality Company name: PAX Technology Limited FCC ID: V5PQ58 FCC Part 15 Certification Pursuant to Sections 0.457 and 0.459 of the commission rules, and in accordance with the FCC Public notice dated June 15, 2004 (DA 04-1705), we hereby request short-term confidentiality for the following items prior to marketing the device.:

(1) Test Setup Photos

(2) External Photos

(3) Internal Photos

(4) User Manual The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Sincerely, Signature Company Name: PAX Technology Limited Contact Name: Jenna tan Title of Person: Certification Leader Address: Room 2416, 24/F., Sun Hung Kai Centre, 30 Harbour Road, Wanchai, Hong Kong, 518057, China

PAX Technology Limited Date: 8/24/2023 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern:

I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) c) d) e) f) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

make claims regarding certification only in respect of the scope for which certification has been granted;

do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

use certification only to indicate the products are certified as being in conformity with specified standards;

g) h) i) j) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to us relating to the products compliance with requirements of the relevant standard and to make these records available to the when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by:

Company Name: PAX Technology Limited Contact Name: Jenna tan Title of Person: Certification Leader Address: Room 2416, 24/F., Sun Hung Kai Centre, 30 Harbour Road, Wanchai, Hong Kong, 518057, China

PAX Technology Limited Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject:

Request for Confidentiality FCC ID:

V5PQ58 To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Company Name: PAX Technology Limited Contact Name: Jenna tan Title of Person: Certification Leader Address: Room 2416, 24/F., Sun Hung Kai Centre, 30 Harbour Road, Wanchai, Hong Kong, 518057, China Date: 8/24/2023