EFT-POS Terminal Instruction Manual S500 1. Installation POWER port connects to the external power adapter. LINE port connects to telephone line. PINPAD port connects to PINPAD. RS232 port connects to serial port. LAN port connects to the network cable (optional). PHONE port connects to telephone (optional). 2. Instructions 1Power ON/OFF Power onPress the ON/OFF button successfully. Power offPress the ON/OFF button successfully. 2Magnetic Stripe Card two seconds until LCD backlight light, the terminal turns on two seconds until LCD no display, the terminal turns off Put magnetic stripe side of magnetic card towards device interior, swipe the card with a steady speed during through magnetic reader slot. (Support bi-directional swiping) 3IC Card Put IC card chip side upward, push-in IC card slot and to bottom. 4Tap contactless card (optional). Put the contactless card into the sensing area above the LCD 5Shred paper operating Instructions Make paper 45 degrees angle right to paper knife and shred paper. 3. Installation and Usage Tips 1Avoid putting the terminal in direct sunlight, high temperature, moist, or dusty environment. 2Forbid non-professional to repair the terminal. 3Before insert the card, please check internal and around of IC card slot . when you found some suspicious objects , must report to related administrator. 4. Password Entering Tips It is highly recommended to enter password as following ways:
1Set up peep shields. Enter password with shield by the structures of cashier desk;
2Place the POS terminal at an appropriate angle and make sure it is difficult to peer the password. For example, the POS was installed above the movable bracket. 3In enter password perspective, avoid surrounding video surveillance;
4Paste text instructions to remind the customers to shelter with body or palm when enter password. 5Merchants can also choose other ways to protect the customer input password. FCC Regulations This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the body of this equipment is a label that contains, among other information, a product identifier . If requested, this number must be provided to the telephone company. RF Exposure Information This device meets the governments requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency
(RF) energy set by the Federal Communications Commission of the U.S. Government. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. PAX TECHNOLOGY LIMITED To know more product details, please visit http://www.pax.com.cn P/N200312000000198 FCC Caution. 15.19 Labelling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. Customer Information This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. This equipment uses the following USOC jacks: RJ11C A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. If this equipment PAXMM00BS500RF causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If trouble is experienced with this equipment PAXMM00BS500RF, for repair or warranty information, please contact PAX Technology Inc. and 631247-9660. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this PAXMM00BS500RF does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.