Please check the components after unpacking. If any one of them is missing, or if there is a page missing from the product manual,ect.,please contact the dealer. 1. Contents Checklist Name E800 AC Power Adapter AC Power cable Thermal Paper Roll Product Manual 2. Product Description Qty. 1 1 1 1 1 3.Installtion USB port:
Micro USB port:
Serial Port:
SIM card slot:
Connect USB device. Connect Micro USB device. Connect serial device. Micro SD card slot:
corresponding SIM card slot. WAN port:
corresponding Micro SD card slot. connected to the Internet into the WAN port to LAN port:
provide wired network for the cash register. Open the SIM card/SD card cover and insert the SIM card in to the Open the SIM card/SD card cover and insert the Micro SD card in to the Open the wire hidden cover at the back of the terminal, insert the cable which is If the WAN port has been connected to the Internet, then the LAN port can Cash drawer interface:
provide network connection. Open the wire hidden cover at the back of the terminal, insert the cash drawer's port into the cash drawer interface on the cash register, so that the cash drawer is connected with the cash Audio Jack:
register. 4. Instruction Use international standard interface. Power ON/OFF Power on:
Press and hold the Power button (on the side) for three seconds until Power off:
the main screen displays normally. Press and hold the Power button (on the side) for three seconds until the shutdown menu appears, tap Shutdown, and then shutting...appears. The Load the print paper:
terminal will be turned off after a few seconds. When the printer's Out of Paper indicator lights in yellow, it needs to load the print paper. Open the external printer cover by pulling it outward with fingers from the printer cover opening. Open the built-in printer cover by pressing inward the spring key. Load the paper roll by following the direction as shown in the paper warehouse, and close the printer cover. Then the indicator will light off.The paper is changed successfully. Open the external printer cover by Magnetic Stripe Card:
pulling it outward with fingers. Then Place the magnetic stripe face down (keep the magnetic stripe card perpendicular to the main display), swipe card through the magnetic IC Card:
card slot at a constant speed. Place the IC chip facedown, insert the IC card into the card slot, and Put the contactless card on the center of the payment Contactless card:
push it to the end. 5. Specification modulescreen. Operation System: Android 6.0 CPU: Quad-coreA17,1.8GHZprocessor Memory: 2GB RAM + 16GB Flash Memory Main Display: 15.6inch,resolution:1920*1080, multi-touch capacitive touch screen Guest Display: 8 inch, resolution: 1280*800, multi-touch capacitive touch screen Printer: 3" high-speed thermal printer with auto-cutter, printing speed:150mm/s Audio: Built-in speaker, support headphone output Camera: 5 mega-pixel auto-focusing camera, high-speed code scanning L-Sensor (Ambient Light Sensor): automatically adjust the backlight brightness of display the main Wireless Communication: Support LAN, WIFI, Bluetooth, 2G/3G/4G Peripheral Ports: 1 Micro-USB port 5 USB ports 3 Network ports(1 WAN port, 2 LAN ports) 1 cash drawer 1 serial port 1 audio jack Card Slot: 1 SIM card slot 1 Micro SD card slot 1 magnetic stripe card/IC card slot, using two-in-one Magnetic Card Reader: Support track 1/2/3. IC Card Reader: Conform to the standard ofISO7816, EMV2000 L1&L2, PBOC3.0 Contactless Card Reader: Compatible with ISO14443 Type A&B 6. Paper Installation support MAG&ICC 1. When the printer is out of paper, the Out of Paper indicator will light in yellow. Open the out ward with fingers from the printer cover opening(that external printer cover by pulling the arrows point to). it 2. Open the built-in printer cover by pressing inward the spring key(that the arrow points to). 3. Open the built-in and external printer covers as shown in the figure. 4. Load the paper roll and make sure a part of paper is exposed. 5. Close the printer covers in turn. The Out of Paper indicator will light off. The paper is changed successfully. 7. Cautions of Installation and Usage Avoid exposing the terminal in hot, humid,dusty or strong electromagnetic environment. Do not violently vibrate, shake or beat the product. Do not plug/unplug any units of the product when it is power on, otherwise it may 1 2 3 damage the internal circuit. 4 Do not maintain the terminal if you are non-professional foreign object 5 Before inserting the magnetic stripe/IC/contactless card, please check whether there is For operation within 5.15 ~ 5.25GHz frequency range, it is restricted to indoor environment any inside or surround the card slot , and if any , report to related personnel. 6 FCC Regulations:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. FCC Caution:
ISED Notice This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
1) 2) this device may not cause interference, and this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
1) 2) l'appareil ne doit pas produire de brouillage, et l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested built-in radios. Cet appareil et son antenne ne doivent pas tre situs ou fonctionner en conjonction avec une autre antenne ou un autre metteur, exception faites des radios intgres qui ont t testes. The County Code Selection feature is disabled for products marketed in the US/ Canada. La fonction de slection de l'indicatif du pays est dsactive pour les produits commercialiss aux tats-Unis et au Canada. Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.