D135 Secure Card Reader 1. Instructions 1) Power ON/OFF Power on: Press button for 3 seconds until Di is heard, and then power indicator light is lighted. Power off: Press button for 3 seconds until four status indicator light is lighted and then off, then the POS terminal is being turned off. IC Card Put IC card chip side upward, push-in IC card slot and to bottom. 2) 3) Contactless Card 4) Battery Charge display The card read area is above the EMV Contactless symbol. Connecting USB port with external adapter can charge the battery. If the power indicator light is flashing red slowly, it indicates that pos is charging. If the power indicator is steady green, it indicates that pos is full charge. 2.Terminal Specifications Processor Cortex M3, 96MHz Memory Space 1MB in-chip Flash and 4MB Out-of-chip Flash,128KB SRAM Keyboard one ON/OFF/Download key. IC Card Reader Conform to ISO7816, EMV L1&L2 and PBOC3.0 standard Magnetic card Conform to ISO7811, ISO7812 standard Contactless Card Conform to ISO14443 TypeA & TypeB;Mifare standard Communication Mode BT Interface 1 Type-C USB (Device) Audio Buzzer Power supply 5V/500mA Working Condition Working temperature: 0~50 Relative humidity: 10%~93% (Non-condensing) Storage Condition Storage temperature: -20~70 Relative humidity: 10%~93% (Non-condensing) 3. Installation and Usage Tips 1Avoid putting the terminal in direct sunlight, high temperature, moist, or dusty environment. 2Forbid non-professional to repair the terminal. 3Before insert the card, please check internal and around of IC card slot. if you found some suspicious objects , must report to related administrator. 4. Lithium Ion Battery Usage Tips 1Avoid putting the battery in sunlight or smoke, dusty environment. 2Forbid crushing, treading ,throwing the battery into fire or liquid. 3Replace the battery immediately if it is damaged(exothermic or distorted). 4It is recommended changing battery that used more than two years. FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC RF Exposure Information (SAR) This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States. During SAR testing, this device is set to transmit at its highest certified power level in all tested frequency bands, and placed in positions that simulate RF exposure in usage near the body. Although the SAR is determined at the highest certified power level, the actual SAR level of the while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The exposure standard for wireless employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: V5PD135 For this device, the highest reported SAR value for usage near the body is 0.22 W/kg. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. ISED Notice This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR Innovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en IC: 11689A-D135 ISED Radiation Exposure Statement This EUT is in compliance with SAR for general population/uncontrolled exposure limits in ISED RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Cet appareil est conforme aux limites d'exposition DAS incontrle pour la population gnrale de la norme CNR-102 science de linnovation et le dveloppement conomique Canada et a t test en conformit avec les mthodes de mesure et procdures spcifies dans IEEE 1528 et IEC 62209. Cet appareil et sa ou ses antennes ne doivent pas tre co-localiss ou fonctionner en conjonction avec tout autre antenne ou transmetteur. PAX TECHNOLOGY LIMITED reserves the right to change product technology specifications without notifying. PAX TECHNOLOGY LIMITED Fax: 0755-86169634 Manufacturer: PAX Computer Technology (Shenzhen) Co., Ltd. Address:4/F, No.3 Building, Software Park, Second Central Science-Tech Road, High-Tech Industrial Park, Shenzhen, Guangdong, P.R.C. Tel: 0755-86169630 Website: http://www.pax.com.cn Responsible Party:
PAX Technology, Inc. 8880 Freedom Crossing Trail, Building 400, 3rd Floor Suite 300, Jacksonville , Florida, USA 32256 Help-desk 1 877-859-0099