FCC ID: V5PIM30L UNATTENDED PAYMENT TERMINAL

Quick Setup Guide IM30 UNATTENDED PAYMENT TERMINAL PAX TECHNOLOGY LIMITED 1. Contents Please make sure the following items are included with your IM30 unattended payment terminal. If any items are missing, contact your dealer. 1 x IM30 Unattended Payment Terminal 4 x M4 nuts 4 x M4 screws 1 x IM30 Mounting Bracket 2. Product Description 3. Installation 1. 4G module SIM and SAM Cards Certain configurations of the IM30 will have a 4G network module, in these configurations you can install a SIM card. Unscrew the 4G network module and remove it to reveal the SIM card slot on the bottom of the module. Push the card into the slot with the contacts facing up and the clipped corner of the card facing towards the module. Certain configurations of the IM30 will have physical SAM card slots available, you may install SAM cards in a similar manner to the SIM cards (make sure to use the appropriate card slots as indicated in figure 6. 2. SAM Cards The IM30 has two dedicated SAM card slots, they can be accessed on the main body of the IM30 after the 4G network module (or the empty back cover) is removed. Open the card mount by sliding the card mount in the OPEN direction indicated on the mount, then insert a SAM card with the contacts facing the IM30 and the clipper corner oriented to the upper left. Lock the card mount by pressing it to the contacts and sliding it in the LOCK direction indicated on the card mount. NoteDo not power on the IM30 while installing or removing SIM or SAM cards. To reassemble the device, slide the two plastic tabs on the left of the module into the corresponding slots on the main body of the IM30, then insert the 4G network board into the board to board connector. Finally, locked the module in place using a screwdriver. 3. Device Dimensions 4. Device Installation 1) Measure the thickness of the mounting plate, this is used later in step 4. 2) The back face of the mounting plate should have four stud bolts corresponding to the mounting points located on mounting bracket. Slide the mounting bracket into place with the orientation shown in figure 9 and then fix it in place with four M4 nuts. 3) Slide the IM30 unit into the mounting plate with the orientation shown in figure 9. The back portion of the device should rest securely inside the mounting bracket. 4) If the mounting plate is 4mm thick, apply a torque of 0.6 ~ 0.8 Nm to the four M4 screws included with your IM30 unit to secure the IM30 to the mounting bracket. If the mounting plate is more than 4mm thick, obtain M4 screws with the following thread length and use them instead:

(mounting plate thickness + 10mm) thread length

(mounting plate thickness + 14mm) 4. Instructions Power on/off Power on: Plug the IM30 into an appropriate power source 24 VDC via the JVMA port, the digital IO port, or the RS232-B RJ45 port. Power off: Disconnect the IM30 from the power source it is connected to. Contactless Transactions When the device is ready to accept a contactless transaction, the contactless icon should appear on screen. Orient the card or NFC device parallel to the screen and then hold it at a distance of 4 cm or less directly above the contactless icon. Code Scanner Transactions When the device indicates on screen that it is ready to scan a 1D or 2D code, orient the code parallel to the code scanning camera and then place it directly in front of the camera. Environmental Conditions Storage Temperature: -30C ~ 70C (-22F ~ 158F) Operating Temperature: -20C ~ 70C (-3F ~ 158F) Relative Humidity: 5% ~ 95% (non-condensing) 5. Maintenance and Usage 1. If any cables become damaged, seek a replacement. 2. Do not insert unknown materials into any port on the IM30, this may cause serious damage to the device. 3. If repairs are required, please contact a professional technician instead of attempting them on your own. 4. The IM30 contains tamper-proofing features; these circuits will trigger if the device is disassembled, at which point it will have to be rearmed before the device is ready to resume operation. 5. The IM30 is designed for outdoor use; however, during normal use its surface should still be keep clear of dirt and possible liquid contaminants. 6. While the IM30 is designed to resist ingress of dust and liquids, it is not designed to resist pressurized liquids such as water hoses. Keep the back of the device away from dust and liquids as much as possible. 7. Make sure the various cables connect to provide the appropriate voltages at the proper pins. 6. Compliance Statements FCC Regulation This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Note Caution: Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. RF Exposure Information This device meets the governments requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm during normal operation. ISED Notice This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

1) l'appareil ne doit pas produire de brouillage, et 2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. CAN ICES-003 (B)/NMB-003(B) This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. ISED RF Exposure Statement This device complies with ISED RSS-102 RF exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the IC RSS-102 RF exposure limits, human proximity to the antenna shall not be less than 20 cm (7.87 inches) during normal operation. Cet appareil est conforme aux limites d'exposition aux rayonnements de la CNR-102 dfinies pour un environnement non contrl. Afin d'viter la possibilit de dpasser les limites d'exposition aux frquences radio de la CNR-102, la proximit humaine l'antenne ne doit pas tre infrieure 20 cm (7.87 pouces) pendant le fonctionnement normal. Battery Warning Do not ingest battery, Chemical Burn Hazard. This product contains a coin / button cell battery. If the coin / button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. TRADEMARK RECOGNITION The Adopted Trademarks HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries. 7. Icons Dispose in a professional recycling manner Class II equipment For indoor use only Energy efficiency marking AC voltage DC voltage PAX Technology Limited Manufacturer: PAX Computer Technology (Shenzhen) Co. Ltd. Address: 4/F, No.3 Building, Software Park, Second Central Science-Tech Road,High-Tech Industrial Park, Shenzhen, Guangdong, China. Tel: +86 755 86169630 Website: www.pax.com.cn Responsible Party: PAX Technology Inc. Address: 8880 Freedom Crossing Trail, Building 400, 3rd Floor, Suite 300, Jacksonville, Florida 32256 Tel: 1-877-859-0099 Website: www.pax.us Although PAX Computer Technology (Shenzhen) Co., Ltd. strives to maintain the accuracy of the information presented in this document, it reserves the right to change product specifications without prior notification and does not guarantee that the material presented herein will accurately reflect the set up, installation, or use of PAX products.

Sf him), da _fF aS we hy waa, UVINE- INAQ20 I

=~v =

zamits~r Pe Ndtillg .V-4OV UL FCC ID: VoPIMS0L 1 IC +-11EGRQ20A_IM20]

rae |

PAN EUV ULET POUMNULUEY VOHRA ll) Nay LU. Made inCnind )

PAX Technology Limited

Date: September 25, 2023 Power of Attorney To whom it may concern, Please be notified that I, Jenna Tan, have designated Jim Tsai in Sporton International Inc. as the person being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Jim Tsai in Sporton International Inc., on the matters of relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002 (b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C 862. This authorization is limited to the product of as following:

FCC ID: V5PIM304GBWL FCC ID: V5PIM30BWL FCC ID: V5PIM30L If you have any acknowledgement and response, please send it to Sporton International Inc. directly. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely yours, ____ Contact Person: Jenna Tan E-mail: certservice@paxsz.com

PAX Technology Limited Date: September 25, 2023 Federal Communications Commission Authorization and Evaluation Division RE

: Certification Application FCC ID: V5PIM304GBWL FCC ID: V5PIM30BWL FCC ID: V5PIM30L To Whom It May Concern, Pursuant to sections 0.457 and 0.459 of CFR 47, Public Notice DA 04-1705 of the Commissions policy and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 180 days:

External Photos Internal Photos Test set-up photos Users Manual The application contains technical information, which PAX Technology Limited deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application Sincerely, ____ Contact Person: Jenna Tan E-mail: certservice@paxsz.com 1/1

PAX Technology Limited Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Date: September 25, 2023 Subject: Certifications concerning covered equipment pursuant to Part 2.911(d)(5)(i) and (ii) To whom it may concern, PAX Technology Limited certifies that the equipment FCC ID: V5PIM304GBWL, FCC ID: V5PIM30BWL and FCC ID: V5PIM30L for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. PAX Technology Limited certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely, ________________________ Name: Jenna Tan E-mail: certservice@paxsz.com

PAX Technology Limited Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Certification designating a U.S. agent for service of process pursuant to Part 2.911(d)(7) To whom it may concern,

[PAX Technology Limited, RFN:0017536285, FCC ID:V5PIM30BWL] certifies that, as of the date of the filing of application, [PAX Technology, Inc.] is designated as the U.S. agent for the purpose of accepting service of process on behalf of the applicant. The physical U.S. address, email for the designated agent are:

Physical U.S. address: 8775 Baypine Road, Jacksonville, FL 32256 Contact name: John Hallisey Email: John.Hallisey@pax.us FRN: 0033507476 The applicant accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The agent accepts the designation by (the applicant) as the U.S. agent to accept service of process includes, but is not limited to, delivery of any correspondence, notices, orders, decisions, and requirements of administrative, legal, or judicial process related to Commission proceedings. Signed by the Applicant Signed by the Agent (if different from the Applicant) PAX Technology Limited /

Name: Jenna Tan John Hallisey General Counse Title:

Email: certservice@paxsz.com Email: john.hallisey@pax.us Date: August 30, 2023 Date: August 30, 2023 Title: Certification Leader