FCC ID: XMR2023FCE860L Wi-Fi & Bluetooth Module

HVINFCE860L FCC ID: XMR2023FCE860L IC: 10224A-2023FCE860L Because the product is too small, FCC ID/IC ID/HVIN information will show in the manual

Applicant/Grantee FCC ID:

Quectel Wireless Solutions Company Limited XMR2023FCU741R XMR2023FCU760K XMR2023FCS960K XMR2023FCE860L Section 15.212 Modular Transmitters Request for Modular Approval Request for Limited Modular Approval Requirements EUT Conditions Comply (Y/N) Single Modular Approval Requirements The radio portion of this module is shielded, please see exhibition external photos. The module has buffer modulation/data inputs. The module has its own power supply regulation. Please see the schem.pdf The requirements of antenna connector and spurious emission have been fulfilled. Please refer to the Test Report exhibition. Please refer to the Setup Photo exhibition for the stand-alone test configuration. Y Y Y Y Y 1 2 3 4 5 The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. The modular transmitter must have its own power supply regulation. The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). The professional installation provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available

(see Section 15.31(i)). The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number.

(A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: XYZMODEL1 or Contains FCC ID:

XYZMODEL1. Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization.

(B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following:

Contains FCC certified transmitter module(s). Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such 6 7 Y The Module will put label in user manual since limited space, and the instruction on the labeling rule of the end product has been stated in the User Manual of this module. Please refer to the Label declaration and User Manual exhibition. The required FCC rule has been fulfilled and all the instructions for maintaining compliance have been clearly stated in the User Manual. Y requirements. A copy of these instructions must be included in the application for equipment authorization. The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. 8 Please refer exhibition RF Exposure for the compliance of MPE RF exposure rule. Y _________________________________ Contact Person: Jean Hu E-mail: jean.hu@quectel.com

Quectel Wireless Solutions Company Limited Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Date: July 31, 2023 Subject: Certifications concerning covered equipment pursuant to Part 2.911(d)(5)(i) and (ii) To whom it may concern, Quectel Wireless Solutions Company Limited certifies that the equipment FCC ID: XMR2023FCU741R/FCC ID:

XMR2023FCU760K/FCC ID: XMR2023FCS960K and FCC ID: XMR2023FCE860L for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Quectel Wireless Solutions Company Limited certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely, ________________________ Name: Jean Hu E-mail: jean.hu@quectel.com

QUECCTEL Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Certification designating a U.S. agent for service of process pursuant to Part 2.911(d)(7) To whom it may concern, Quectel Wireless Solutions Company Limited, FRN: 0018988279, Grantee Code: XMR (the applicant) certifies that, as of the date of the filing of application, Ikotek USA, Inc., FRN: 0033350331 (the agent) is designated as the U.S. agent for the purpose of accepting service of process on behalf of the applicant. The physical U.S. address and email for the designated agent are:

Physical U.S. address: 9920 Pacific Heights Blvd., Ste. 150, #7025, San Diego, CA 92121 Email: compliance@ikotek.com The applicant accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The agent accepts the designation by (the applicant) as the U.S. agent to accept service of process includes, but is not limited to, delivery of any correspondence, notices, orders, decisions, and requirements of administrative, legal, or judicial process related to Commission proceedings. Signed by the Applicant Signed by the Agent (if different from the Applicant) 7 he! Jean Hu Name: eterson Title Certification Manager Title: CEO. Email: Jean.hu@quectel.com Email: joe.peterson@ikotek.com Date: 07 July, 2023 Date: 07 July, 2023

Quectel Wireless Solutions Company Limited Date: July 31, 2023 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: XMR2023FCU741R FCC ID: XMR2023FCU760K FCC ID: XMR2023FCS960K FCC ID: XMR2023FCE860L Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Part List Schematics Block Diagram Operation Description Tune up Procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, ________________________ Rev. 1/1/03 Contact Person: Jean Hu E-mail: jean.hu@quectel.com Rev. 1/1/03

Quectel Wireless Solutions Company Limited Power of Attorney Date: July 31, 2023 To whom it may concern, Please be notified that I, Jean Hu, have designated Jim Tsai in Sporton International Inc. as the person being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Jim Tsai in Sporton International Inc., on the matters of relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002 (b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C 862. This authorization is limited to the product of as following:

FCC ID: XMR2023FCU741R FCC ID: XMR2023FCU760K FCC ID: XMR2023FCS960K FCC ID: XMR2023FCE860L If you have any acknowledgement and response, please send it to Sporton International Inc. directly. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely yours, ____ Contact Person: Jean Hu E-mail: jean.hu@quectel.com

Quectel Wireless Solutions Company Limited Date: July 31, 2023 Federal Communications Commission Authorization and Evaluation Division RE

: Certification Application FCC ID: XMR2023FCU741R FCC ID: XMR2023FCU760K FCC ID: XMR2023FCS960K FCC ID: XMR2023FCE860L To Whom It May Concern, Pursuant to sections 0.457 and 0.459 of CFR 47, Public Notice DA 04-1705 of the Commissions policy and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 180 days:

External Photos Internal Photos Test set-up photos Users Manual The application contains technical information, which Quectel Wireless Solutions Company Limited deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application Sincerely, ____ Contact Person: Jean Hu E-mail: jean.hu@quectel.com 1/1