WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6672237.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case RTL8851BE Users Manual RTL8851BE 11ax RTL8851BE Combo module Users Manual Preliminary Version 2022/12/20 Realtek Semiconductor Corp. No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan Tel.: +886-3-578-0211. Fax: +886-3-577-6047 www.realtek.com RTL8851BE Users Manual CONTENT TEMPERATURE ............................................................................................................................... 3 WARNING .......................................................................................................................................... 3 Federal Communication Commission Interference Statement ...................... 3 INDUSTRY CANADA STATEMENT ......................................................................................................... 13 NCC .................................................................................................... 13 RTL8851BE Users Manual Temperature Warning Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the RTL8851BE Users Manual party responsible for compliance could void the user's authority to operate this equipment. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. FCC regulations restrict the frequency 5850-5895MHz operation of this device to indoor use o0nly. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. The SAR test is according to KDB 616217 for test requirements. The maximum output power is reduced by software to perform SAR evaluation as application. The SAR evaluation is according to KDB 616217, and the module approach distance restriction is 5 mm for notebook, 10 mm for tablet. When this module is installed into the host as portable configuration, only PIFA Antenna as described in this use manual is applicable. When other antenna type is used, it is required for a separate reassessment through a class II permissive change application or new certification RTL8851BE Users Manual This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module:
KDB 996369 D03 OEM Manual v01 rule sections:
2.2 List of applicable FCC rules This module has been tested for compliance to FCC Part 15 2.3 Summarize the specific operational use conditions The module is tested for standalone mobile RF exposure use condition. Any other usage conditions such as co-location with other transmitter(s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification. 2.4 Limited module procedures Not applicable. 2.5 Trace antenna designs Not applicable. 2.6 RF exposure considerations This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator &
your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules. 2.7 Antennas The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. The antenna must be installed such that 20 cm can be maintained between the antenna and users. RTL8851BE Users Manual 2.8 Label and compliance information The final end product must be labeled in a visible area with the following:
Contains FCC ID: TX2-RTL8851BE. The grantee's FCC ID can be used only when all FCC compliance requirements are met. 2.9 Information on test modes and additional testing requirements This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) or portable use will require a separate class II permissive change re-evaluation or new certification. 2.10 Additional testing, Part 15 Subpart B disclaimer This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can RTL8851BE Users Manual not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. OEM/Host manufacturer responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules. This module must not be incorporated into any other device or system without retesting for compliance as multi-radio and combined equipment Industry Canada statement:
This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an RTL8851BE Users Manual uncontrolled environment. This equipment should be installed and operated with greater than 20cm between the radiator & your body. Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis plus de 20 cm entre le radiateur et votre corps. Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Dclaration d'exposition aux radiations:
Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada tablies pour un environnement non contrl. Le produit est sr pour un fonctionnement tel que dcrit dans ce manuel. La rduction aux expositions RF peut tre augmente si l'appareil peut tre conserv aussi loin que possible du corps de l'utilisateur ou que le dispositif est rgl sur la puissance de sortie la plus faible si une telle fonction est disponible. The SAR test is according to KDB 616217 for test requirements. The maximum output power is reduced by software to perform SAR evaluation as application. Le test SAR est conforme KDB 616217 pour les exigences de test. La puissance de sortie maximale est rduite par un logiciel pour effectuer une valuation SAR en tant qu'application. The SAR evaluation is according to KDB 616217, and the module approach distance restriction is 5 mm for notebook, 10 mm for tablet. L'valuation SAR est conforme KDB 616217, et la restriction de distance d'approche du module est de 5 mm pour le portable, 10 mm pour la tablette. When this module is installed into the host as portable configuration, only PIFA RTL8851BE Users Manual Antenna as described in this use manual is applicable. When other antenna type is used, it is required for a separate reassessment through a class II permissive change application or new certification Lorsque ce module est install dans l'hte en tant que configuration portable, seule l'antenne PIFA telle que dcrite dans ce manuel d'utilisation est applicable. Lorsqu'un autre type d'antenne est utilis, il est requis pour une rvaluation distincte via une demande de changement permissif de classe II ou une nouvelle certification Opration porte sur le corps Cet appareil a t test pour des oprations typiques portes sur le corps. Pour se conformer aux exigences d'exposition RF, une distance de sparation minimale de 5 mm doit tre maintenue entre le corps de l'utilisateur et le combin, y compris l'antenne. Les clips de ceinture, les tuis et les accessoires similaires tiers utiliss par cet appareil ne doivent contenir aucun composant mtallique. Les accessoires ports sur le corps qui ne rpondent pas ces exigences peuvent ne pas tre conformes aux exigences d'exposition RF et doivent tre vits. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed and operated with greater than 20cm between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit tre install et exploit avec plus de 20 cm entre l'antenne et les utilisateurs, et 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit RTL8851BE Users Manual supplmentaires requis pour ce module install. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:
Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed and operated with greater than 20cm between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC:
6317A-RTL8851BE. Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un appareil o lantenne peut tre installe et utilise plus de 20 cm entre lantenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des IC: 6317A-RTL8851BE ". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. RTL8851BE Users Manual Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate;
(iv) where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated. Avertissement:
Le guide dutilisation des dispositifs pour rseaux locaux doit inclure des instructions prcises sur les restrictions susmentionnes, notamment :
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
(ii) pour les dispositifs munis dantennes amovibles, le gain maximal dantenne permis pour les dispositifs utilisant les bandes de 5 250 5 350 MHz et de 5 470 5 725 MHz doit tre conforme la limite de la p.i.r.e;
(iii) pour les dispositifs munis dantennes amovibles, le gain maximal dantenne permis (pour les dispositifs utilisant la bande de 5 725 5 850 MHz) doit tre RTL8851BE Users Manual conforme la limite de la p.i.r.e. spcifie, selon le cas;
(iv) lorsquil y a lieu, les types dantennes (sil y en a plusieurs), les numros de modle de lantenne et les pires angles dinclinaison ncessaires pour rester conforme lexigence de la p.i.r.e. applicable au masque dlvation, nonce la section 6.2.2.3, doivent tre clairement indiqus This radio transmitter [IC: 6317A-RTL8851BE] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Le prsent metteur radio [IC: 6317A-RTL8851BE] a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'metteur. NCC Statement RTL8851BE Users Manual 1. 2. XXXyyyLPDzzzz-x NCC LOGO Japan Statement Host system must be labeled with "Contains MIC ID:xxxxxx, MIC ID displayed on label. This device complies with Directive 2014/53/EU and UK Radio Equipment Regulations 2017 SI 2017/1206. issued by the Commission of the European Community. RTL8851BE Users Manual RTL8851BE Users Manual
- Declaration of Conformity The frequency and maximum transmitted power in EU are listed as below Output Power (e.i.r.p.) WLAN:
2.4GHz: 19.98 dBm 5.18~5.24 GHz : 22.77 dBm 5.26~5.32 GHz :22.80 dBm 5.50~5.70 GHz : 22.95 dBm 5.745~5.825 GHz : 13.88 dBm BT-LE: 11.06 dBm BT-EDR: 16.55 dBm RTL8851BE Users Manual The frequency and maximum transmitted power in UK are listed as below Output Power (e.i.r.p.) WLAN:
2.4GHz: 19.98 dBm 5.18~5.24 GHz : 22.93 dBm 5.26~5.32 GHz :22.97 dBm 5.50~5.70 GHz : 22.95 dBm 5.69~5.72 GHz: 28.03 dBm 5.745~5.825 GHz : 22.99 dBm BT-LE: 11.06 dBm BT-EDR: 16.55 dBm
- WLAN 5GHz: Operations in the 5.15-5.35GHz band are restricted to indoor usage only. RTL8851BE Users Manual Installing the Wireless NGFF module Hardware Installing PCIe NGFF2230 module to PCIe NGFF2230 connector and connect two external Wi-Fi antennas on I-PEX connectors. RTL8851BE Users Manual Un-installing the Wireless NGFF module Hardware Remove 2 external Wi-Fi Antennas from the Wireless PCIe NGFF2230 module board and remove the Wireless PCIe NGFF2230 module board from PCIe NGFF2230 connector port RTL8851BE Users Manual Installing the WLAN & Bluetooth USB NGFF module Software Before you proceed with the installation, please notice following descriptions. Note1: The following installation was operated under Windows 7. Note2: If you have installed the WLAN driver & utility before, please uninstall the old version first. A. Execute the setup.exe, Click Next to process the installation B. Select I accept the terms in license agreement and click Next to process the installation RTL8851BE Users Manual C. Click Next button. D. Select Complete and click Next button. RTL8851BE Users Manual E. Click Install button. F. Click Finish button. RTL8851BE Users Manual G. Please click to continue. H. Please click to continue. RTL8851BE Users Manual I. Please click to start installation. J. Please click to finish the installation. Un-installing the Wireless NGFF module Software A. Uninstall the RTL8852BE WLAN Driver from Start Control Panel Programs Please select items as below and click Uninstall to remove RTL8852BE WLAN, BT driver and MP UI.