16 2.0-CHANNEL SOUNDBAR Model: ONA19SB002 PRODUCT GUIDE Ver. 01 Rev.02/08/18 Specications Output Power: 12.5W x 2(RMS) Frequency Response: 50Hz~20 KHz S/N Ratio: 65dB Separation: 45dB USER MANUAL INSERTS FOR FCC ID 1. Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 2. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 3. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. 4. RF Exposure Statement To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. Package contents Speaker Overview 1. Soundbar 1pc 2. 3.5mm audio to RCA audio cable (Length: 1.5m) 1pc 3. Remote control 1pc 4. Product Guide 1pc 5. External adaptor 1pc AUX OPT Product Guide 1 2 3 4 5 2 1. Status indicator 2. Wall mount 3. Aux in 4. Optical 5. Power 6. Power on / o 7. Source 8. Volume down 9. Volume up 6 7 8 9 Status indicator Standby Optical Aux in Bluetooth pairing mode Bluetooth device connected Volume up and down Maximum and minimum volume Mute TV mode Music mode Movie mode Solid Red Solid Green Solid White Flashing blue Solid blue Corresponding to the sound source indicator light ash 1 time Corresponding to the sound source indicator light ash 3 times Slow ash Corresponding to the sound source indicator light ash 2 times Corresponding to the sound source indicator light ash 2 times Corresponding to the sound source indicator light ash 2 times Remote control 1 3 6 9 10 13 AUX OPT 2 4 5 7 8 11 12 1.Power on o 2. Mute 3.Bluetooth 4.Aux 5. Optical 6. TV mode 7. Music mode 8. Movie mode 9. Volume up 10. Previous track 11.Play / Pause 12.Next track 13.Volume down Remote control Batteries Before rst use To prepare the remote control for rst use, pull out the safety strip to activate the battery. Replacing the battery When replacing the battery in the remote control, refer to the diagram below. 1. Pree the catch across. 2. While holding the catch, open the battery door. 3. Fit the battery observing ploarity as shown. When replacing the battery, use only the same CR2025 type specied. Power and connection Power and connection 1. Plug the DC cable from the AC adaptor into the Power jack on the back panel, and plug the AC adaptor into the wall socket. 2. Press to power on/power o. 3.Connect the audio cable to the audio output of any device (such Desktop PC, Laptop, Smartphone Tablet, MP3, TV etc.)with a 3.5 mm headphone output jack or RCA output jack. Bluetooth Connection 1. Turn on the sound bar and select the Bluetooth mode. 2. Activate the Bluetooth function on your device and search for devices nearby. 3. Find Onn 16 Soundbar in the search results and tap to connect. 4. The Bluetooth indicator will turn solid blue on upon a successful connection. Note:
The Bluetooth indicator will keep ashing when the sound bar is pairing. Please make sure no other active Bluetooth devices are within range, and that the sound bar is within 3ft / 1m away from your device. Before starting to play via Bluetooth, please lower the volume to a moderate level. T V Included Not included