FCC ID: HBOSB2225 2.0 LED Soundbar

SB2225-Wall-mounted indication card How to Wall-mount the Soundbar 1. Place the included wall mounting template against to the wall. Mark the two bracket holes using a pencil (not included). 2. Fasten the screws and screw brackets to the wall on the bracket holes. 3. Hang the soundbar on the screws. Screw Size: 47 x 4mm (1.85 x 0.157inch) Screw Bracket Size40 x 8mm (1.575 x 0.315inch) 2.0 LED Soundbar Model:100075108 Wall Mounting Template 2.0 LED Soundbar Model:100075108 Wall Mounting Template 356mm(14.016inch) MARK HERE MARK HERE 14~15mm

(0.55~0.59 inch) WALL MARK HERE MARK HERE LEGAL & COMPLIANCE IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS 1. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 2. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 3. RF Exposure Statement To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. 1. Read these instructions All the safety and operating instructions should be read before this product is operated. 2. Keep these instructions The safety and operating instructions should be retained for future reference. 3. Heed all warnings All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow all instructions All operating and use instructions should be followed. 5. Do not use this apparatus near water The appliance should not be used near water or moisture for example, in a wet basement or near a swimming pool, and the like. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug the apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Do not install this equipment in a confined or building-in space such as a book case or similar unit, and remain a well ventilation conditions. The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, table-cloths, curtains etc. 16. WARNINGTo reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that objects filled with liquids, such as vases, shall not be placed on apparatus. 17. WARNING: The mains plug is used as disconnect device, the disconnect device shall remain readily operable. 18. This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth. 19.

- This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

- Warning: To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel.

- The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance. 4.0mm 4 7 m m 20.The equipment shall be used at maximum 35 degree C ambient temperature. 21. WARNING: To prevent injury, this apparatus must be securely attached to the floor/wallin accordance with the installation instructions. CAUTION:

Risk of explosion if the battery is replaced by an incorrect type replacement of a battery with an incorrect type that can defeat a safeguard

(for example,in the case of some lithium battery types);

disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;

leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas;

a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN 22. Batteries should not be exposed to excessive heat such as sunshine, fire, or the like. WARNING: Danger of explosion if the remote control batteries are incorrectly replaced. Replace only with the same or equivalent type. 23. Keep new and used batteries away from children. 24. If the battery compartment does not close securely, stop using the product and keep it away from children. 25. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. 480x80mm folding to 80x80mm 18.9x3.15in folding to 3.15x3.15in 12.005.0004.05564

(mm) 480X80() 80x80() 21SB2225 Sound Bar SB2225 SB2225 20211124 P 12/p A0 RoHS2.0 Reach 94/62/EC 1mm0<a50+0.3/-0.2 50<a150+1/-0.5>150

+1.5/-1 2 3 A/2

XXXXXX 58mm Model No.:100075108 FCC ID: HBOSB2225 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Input :100-240V~50/60Hz 0.3A 30mm 62368-1 Walmart Inc. Made in China Model No.: 100075108 FCC ID: HBOSB2225 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Input :100-240V~50/60Hz 0.3A 62368-1 Walmart Inc. Made in China size 5.321X5.321mm A0 1 2 3 RoHS2.0 Reach 94/62/EC A/2

SHENZHEN FENDA TECHNOLOGY CO., LTD. Agent Authorization Company: SHENZHEN FENDA TECHNOLOGY CO., LTD. Address: Fenda Hi-Tech Park,Zhoushi Road,Shiyan Town,Baoan District, Shenzhen City,Guangdong,China Product Name: 2.0 LED Soundbar Model Number(s): 100075108 Product Description: 2.0 LED Soundbar We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Date: 2021.12.21 Name:

frank Chenzhonghua Title:

engineer Company: SHENZHEN FENDA TECHNOLOGY CO., LTD.

SHENZHEN FENDA TECHNOLOGY CO., LTD. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject; Request for Confidentiality FCC ID: HBOSB2225 Date: 2021/12/21 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description SOFTWARE SECURITY REQUIREMENTS FOR U-NII DEVICES In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: frank Chenzhonghua Title: engineer Email: frank.chenzhonghua@fenda.com