FCC ID: ZDEFI8919W Wireless Outdoor Pan/Tilt IP Camera

UserUser Manual Manual Model: FI8919W Outdoor Pan/Tilt Wireless IP Camera wwww.foscam.co ww.foscam.comm Table of Contents 11 Overviews Overviews................................................................................................................................................2 Features.......................................................................................................................................................................3 1.11.1 KeyKey Features 1.21.2 ReadRead Before Before UseUse................................................................................................................................................................3 1.31.3 Packing Packing Contents Contents............................................................................................................................................................... 4 1.41.4 Physical Physical Description Description.......................................................................................................................................................... 4 22 Surveillance Surveillance Software 2.12.1 Login Software GUIGUI.................................................................................................................. 7 Window..................................................................................................................................................................... 7 Login Window 2.2 Surveillance Window......................................................................................................................................................... 9 33 Advanced Advanced Camera Settings.............................................................................................................. 16 3.1 Device Status....................................................................................................................................................................16 Camera Settings 3.23.2 Alias Settings.................................................................................................................................................................... 18 3.33.3 Date & Time Settings.......................................................................................................................................................18 3.43.4 UserUser Settings Settings.................................................................................................................................................................... 19 3.5 Multi-Device Settings.......................................................................................................................................................20 3.63.6 Basic Network Settings................................................................................................................................................... 26 3.73.7 Wireless Wireless Settings Settings............................................................................................................................................................. 29 3.83.8 ADSL ADSL.................................................................................................................................................................................. 33 3.93.9 UPnP Settings.................................................................................................................................................................. 34 3.10 DDNS Service Settings.................................................................................................................................................35 3.11 Mail Service Settings.....................................................................................................................................................40 3.12 MSN Setting....................................................................................................................................................................41 3.13 FTP Service Settings.....................................................................................................................................................43 3.14 Alarm Service Settings..................................................................................................................................................46 3.15 PT Settings..................................................................................................................................................................... 52 3.16 Upgrade Device Firmware............................................................................................................................................53 3.17 Backup & Restore Settings.......................................................................................................................................... 55 3.18 Restore Factory Settings..............................................................................................................................................55 3.19 Reboot Device................................................................................................................................................................56 3.20 Log................................................................................................................................................................................... 56 3.21 Back................................................................................................................................................................................. 56 44 APPENDIX APPENDIX............................................................................................................................................. 57 Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 1 1 4.1 Frequently Asked Questions.......................................................................................................................................... 57 4.2 Default Parameters..........................................................................................................................................................61 4.3 Specifications....................................................................................................................................................................61 wwww.foscam.co ww.foscam.comm 55 OBTAINING OBTAINING TECHNICAL TECHNICAL SUPPORT SUPPORT............................................................................................... 62 11 Overviews Overviews FOSCAM FI8919W is an integrated wireless IP Camera with a color CMOS sensor. It combines a high quality digital video camera, with a powerful web server, to bring clear video to your desktop from anywhere on your local network or over the Internet. With flexible 355-degree pan and 90-degree tilt, FI8919W gives users more comprehensive control over a monitored site. The IPCAM supports IR-CUT, when light conditions turns poor, the IR cut filter will be automatically removed to accept IR illumination. Meanwhile, the camera switches itself automatically from color to black and white, assuring optimal image quality at all times. The IPCAM is based on the TCP/IP standard. There is a WEB server inside which could support Internet Explore. Therefore the management and maintenance of your device is simplified by using the network to achieve the remote configuration, start-up and to upgrade the firmware. FI8919W is designed for outdoor surveillance applications such as gardens, courtyards or parks. Controlling the IPCAM and managing images are simplified by using the provided web interface across the network utilizing wireless connectivity. FOSCAM provides Phone APPs for Android and iPhone users, please search Foscam ip cam viewer and install it through APP Store, then you can view your camera directly as a computer. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 2 2 wwww.foscam.co ww.foscam.comm 1.11.1 KeyKey Features Features Powerful high-speed video protocol processor 300K Pixels IR night vision (Range: 15m) Pan 355 degree, tilt 90 degree Optimized MJPEG video compression for transmission Multi-level users management and passwords definition Embedded Web Server for users to visit by IE Wi-Fi compliant with wireless standards IEEE 802.11b/g/n Embedded FOSCAM DDNS (dynamic domain name service) Service Motion detection activates alarm Supports image snapshot Supports multiple network protocols: HTTP/TCP/IP/UDP/STMP/DDNS/SNTP/DHCP/FTP Supports WEP/WPA/WPA2 encryption Supports WPS(Wi-Fi Protected Set-up) Supports Daylight Saving Time Supports MSN Supports Gmail as sender on mail service settings Providing Phone APPs for Android and iPhone users Providing Central Management Software to manage or monitor multi-cameras 1.21.2 ReadRead Before Before UseUse Please first verify that all contents received are complete according to the Package Contents listed below. Before the Network Camera is installed, please carefully read and follow the instructions in the Quick Installation Guide to avoid damage due to faulty assembly and installation. This also ensures the product is used properly as intended. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 3 3 wwww.foscam.co ww.foscam.comm 1.31.3 Packing Packing Contents Contents IPCAM1 Wi-Fi Antenna1 DC Power Supply1 Mounting bracket1(option) CD1 Quick Installation Guide1 Warranty Card1 Network Cable1 1.41.4 Physical Physical Description Description Front Panel Lens Infrared Led Infrared Led Figure 1.1 Infrared LED: 22 IR LEDs, night visibility up to 15 meters LENS: CMOS sensor with fixed focus lens Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 4 4 Back View wwww.foscam.co ww.foscam.comm Antenna Figure 1.2 WIFI Antenna: Wireless Antenna Interface View Power LAN Reset button Figure 1.3 LAN: RJ-45/10-100 Base T Power: DC 12V/2A Power supply Reset button:

1) Press and hold down the RESET BUTTON about 10 seconds. when released the IP camera will be reset back to factory default settings. You must power on the camera before reset. 2) Press and hold down the RESET BUTTON about 4 seconds, then press the WPS button on the router, you can use the WPS function. (For more details: please read Wireless Settings in the User Manual) Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 5 5 wwww.foscam.co ww.foscam.comm Bottom View There are up to three labels located on the body of the camera; this is an important feature of original Foscam cameras. If your camera does not have labels as shown in Figure 1.3 ,it may be a clone one. Cloned Foscam cameras can not use original firmware and are not eligible for warranty or technical services. FOSCAM domain name S/N of FOSCAM address of MAC wireless connection address MAC wired connection of Figure 1.3 Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 6 6 wwww.foscam.co ww.foscam.comm 22 Surveillance Surveillance Software Software GUIGUI Please refer to the Quick Installation Guide if you install the camera at first time. After finishing quick installation, you can take time to learn the operation of the software. 2.12.1 Login Login Window Window Figure 2.1 Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 7 7 wwww.foscam.co ww.foscam.comm Please check the login window above, it was divided to 7 sections from no. 1 to 7. Section1 Select Language FOSCAM camera supports up to multi-languages, such as English, Spanish, Deutsch and so on. You can select the language you need via pull down the dropdown toolbar and click on the language to switch. Section 2 Enter the Username and password The default administrator username is admin with no password. Section3 FOSCAM Website Link There is an access link to Foscam website homepage, if you need tech support you can contact Foscam directly. Section4 ActiveX Mode If your PC is windows based OS, such as Windows XP, Windows7, Windows Vista and you are using IE-based browsers like IE6, IE7, IE8, please choose IE ActiveX Mode login mode. Section5 Server Push Mode If you are using non-IE based browser, like Firefox, Safari, Google Chrome please choose Server Push Mode. Section6 Mobile Phone If you are using the Mobile to access the camera, here you need to select Mobile Phone login mode. Section7 Note Note that when you login the camera, please select the corresponding login mode. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 8 8 2.2 Surveillance Window Select the ActiveX mode and you will enter the surveillance window. wwww.foscam.co ww.foscam.comm 6 1 2 3 4 5 Section1 Device Name Figure 2.2 7 Default device name is Anonymous. You can define a name for your camera as you like (Please go to chapter 3.1 and read how to set it) Section2 Multi-Device Window The firmware inside the camera supports up to maximum of 9 cameras being monitoring at the same time. You can add other cameras in multi-device setting (read chapter 3.5). Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 9 9 wwww.foscam.co ww.foscam.comm Section3 Image Parameters Settings

. Figure 2.3 OSD OSD is used to add timestamp on the video. There are five text colors to choose from: Black, red, yellow, white, blue. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 10 10 wwww.foscam.co ww.foscam.comm Add OSD on record Select this option if you want to add a timestamp to recordings. Resolution 1) 320x240-------QVGA 2) 640x480-------VGA There are two resolutions, the bigger one (VGA) is 640x480 pixels, and the smaller one (QVGA) is 320x240 pixels. The bigger the resolution, the better of the image quality is, but the lower the frame rate is. If you are accessing the camera via internet and want to get more fluent video streaming, please select resolution QVGA 320x240. Mode 1) 50HZ ---------Indoor surveillance (Region: Europe, China) 2) 60HZ ---------Indoor surveillance (Region: USA, Canada) 3) Outdoor-------Outdoor surveillance (Region: All over the world) There are three options within the menu of Mode: 50HZ, 60HZ and Outdoor. It depends on the frequency of the electricity and surveillance model (indoors & outdoor). Please choose outdoor mode, when the camera was installed outside. Fps 1) Max---------- Maximum frame rate 2) 20fps, 15fps, 10fps, 5fps,4fps,3fps,2fps,1fps, 5fps, 1fps ,1/2fps,1/3fps,1/4fps,1/5fps-------

customized frame rate You can choose option within the menu of Fps to adjust the frame rate. It is often used in LAN network when you want to lower the frame rate, so that you can save more bandwidth. Brightness Default parameter is 6, you can adjust the brightness of the image by clicking plus or minus button. Contrast Default parameter is 4, you can adjust the contrast of the image by clicking plus or minus button. Preset/Go 1) Preset----------Support 8 preset position, which is considered enough for DIY home & small business surveillance market Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 11 11 wwww.foscam.co ww.foscam.comm 2) Set----------- Click Set to save the position you need the camera to remember 3) Go----------- Click Go to make the camera move the preset position 4) Number button from 1 to 8--------You can click the number button with preset position, and the camera will go to the preset position. How to do preset position?

We can start preset settings from position 1. Firstly, select no. 1 within the menu of Preset on the panel. Secondly, move the camera and stop at a place where you want make preset position. Thirdly, click set button to save it as position 1 and you have done preset of position 1. After that, you can select no. 2 within the menu of Preset on the panel, and move the camera and stop at another place, and set as preset position 2. You can do all the 8 preset positions with this method. If you want to see the preset position you have set, such as the position 1, only select the set no.1 ,and click go button, the camera will go to position no.1. Flip & Mirror You can flip the image by enabling Flip button, or mirror the image by enabling Mirror button. Section4 Pan/Tilt Control 5 7 3 1 2 6 9 4 8 1------Up control button, 3------Left control button, 5----- Up-Left control button 7----- Down-Left control button 9------Go to center 2------Down control button, 4------Right control button, 6----- Up-Right control button 8----- Down-Right control button Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 12 12 wwww.foscam.co ww.foscam.comm

: Click this icon; camera will rotate up and down. Click

: Click this icon; camera will rotate left and right. Click to stop. to stop.

: Click this icon, all the IR lights will turn on. Click to turn off them. Section5 Device Management Device Management ------Path to Administrator Control Panel, Click it, and it will lead to Administrator Control Panel. Section6 Record & Snapshot & Full Screen Buttons 1 2 3 1------Record Button Click it and it pop-up a path-setting window, you can select the storage path and the record file name. At the same time the record icon changes to and stop recording. 2------Snapshot Click it to make snapshot and it pop-up a window which picture you snapshot, right click in the window and save the picture to anywhere you want. 3------Full Screen Click it to make full-screen or you can double click the surveillance screen to make full-screen.

,, Click it again Section7 Play/Stop Buttons 1 2 1------Play Click it to play the video of the camera 2------Stop Click it to stop the video of the camera Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 13 13 wwww.foscam.co ww.foscam.comm Onscreen Mouse Control Double click right mouse on the surveillance window, then left click on the screen to indicate the camera move direction you prefer, press the left mouse and the camera Len will move to the corresponding direction.. Double click right mouse again, cancel onscreen mouse control. For example, double click right mouse, then left click on the up corner of the screen, you can see the arrow, press the left mouse, and the cameras lens will moving towards the up direction. Double click right mouse again, cancel onscreen mouse control. Figure 2.4 Record and multi-device function are controlled by ActiveX controller, Google Chrome, Safari browsers will not allow these functions. For Firefox, Google Chrome, Safari, you should select the Server Push Mode and you can see the following screen:

therefore Firefox or Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 14 14 wwww.foscam.co ww.foscam.comm 15 15 Figure 2.5 Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited wwww.foscam.co ww.foscam.comm Advanced Camera 33 Advanced Click the bar Device Management, goes to Administrator Control Panel to make advanced camera settings. Camera Settings Settings 3.1 Device Status Figure 3.1 1------Device ID MAC ID of the camera by wired connection 2-----Device Firmware Version System Firmware version of the camera 3-----Device Web UI Version Web UI firmware version of the camera 4-----Alias Name of the camera 5-----Alarm Status The status of Alarm Service Setting 6-----DDNS Status The status of DDNS Setting 7-----UPnP Status The status of UPnP Setting 8-----MSN Status The status of MSN Setting Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 16 16 wwww.foscam.co ww.foscam.comm Another Way:

Double click the the icon IP Camera.exe

, select the camera IP, right click and select the Basic Properties, you can also see the Firmware Version and MAC Address, such as the following screen:

Figure 3.2 Figure 3.3 Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 17 17 wwww.foscam.co ww.foscam.comm 3.23.2 Alias Settings Default alias is Anonymous. You can define a name for your camera here such as apple. Click Submit to save your changes. The alias name supports special characters. Click the option here to modify the device name Enter the device name as you like. Use different names to identify multi-cameras 3.33.3 Date & Time Settings Figure 3.4 Choose the time zone of your country. You can choose Sync with NTP Server or Sync with PC Time. If your country implements the Daylight Saving Time, that option can also be selected. Go to Data &Time Settings Select the time zone belong to your region Figure 3.5 Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 18 18 wwww.foscam.co ww.foscam.comm 3.43.4 UserUser Settings Settings Here you can create users and set permission levels, visitor, operator or administrator. Click Submit to save these settings. The camera will reboot. You can set different permission levels, but at least one administrator Figure 3.6 Here you can also set one important file locations for the camera, the Alarm Record Path. Simply click Browse and choose the path to the required folder. The Alarm Record Path location is used to store automatically recorded files when the camera is activated by motion. (See set motion alarm. Figure 3.39) The default path for Alarm Record Path is C:\Documents and Settings\All Users\Documents. NOTE: In Windows7 or Vista, if you cannot set the paths.:

Windows7 or Vista's security level is higher than Windows XP/2000.For "set record path"

function, user should add the Device IP address to the Internet Explorer's 'Trusted sites' first. The step is: IE browserToolInternet ProperSecurityTrusted sitesSitesAdd Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 19 19 wwww.foscam.co ww.foscam.comm 3.5 Multi-Device Settings If you want to view multi-surveillance screens on one window, you need to login one camera, and set it as the main device, and do Multi-Device Settings, add other cameras to the first one camera. Before you do multi-cams settings, you need to assign different port such as 81, 82, 83, 84, 85, 86, 87, 88 to the cameras if there is 8 cams installed. The firmware within the camera can support a maximum of 9 devices monitoring all at the same time. 3.5.1 Add cameras in LAN In Multi-Device Settings page, you can see all devices searched in LAN. The 1st Device is the default one. You can add more cameras in the list in LAN for monitoring. The cameras software supports up to 9 IP Cameras online simultaneously. Click The 2nd Device and click the item in the Device List in LAN, the Alias, Host and Http Port will be filled in the boxes below automatically. Enter the correct username and password then click Add. Add more cameras in the same way. After all cameras have been added, choose Submit. 1 Click it, alias, host and HTTP Port will be filled in the following boxes automatically 2 Enter the User name and password of the 2nd camera 3 Click Add to take effect Figure 3.7a Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 20 20 wwww.foscam.co ww.foscam.comm Back to Surveillance Windows, and click Four Windows option, you will see four cameras you added. Figure 3.7b Click Submit after add all cameras Figure 3.8 Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 21 21 wwww.foscam.co ww.foscam.comm Figure 3.9 3.5.2 Add cameras in WAN If you want to view all cameras via the internet(remote computer), you will need to add them using DDNS domain name. Firstly, make sure all of the cameras you added can be accessed through the internet. (Read How to configure DDNS settings in chapter 3.10) Login to the first camera using a DDNS domain name and port. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 22 22 wwww.foscam.co ww.foscam.comm Use DDNS domain name and port to login Make sure each camera you need add could login with DDNS name and port Figure 3.10 If you have several cameras, you can use the same DDNS domain name; you only need to set a different port number for each camera. Click Multi-Device Settings. Choose The 2nd Device. Fill in the 2nd cameras name, DDNS domain name, port number. Enter user name and password and then choose Add. (Figure 3.11) NOTE: Here the Host must be entered as the second cameras DDNS domain name, not its LAN IP. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 23 23 wwww.foscam.co ww.foscam.comm 1 2 3 24 24 4 Figure 3.11 1----- The 2nd cameras name 2----- Fill in the 2nd cameras DDNS host not LAN IP 3 ---- Enter the 2nd cameras user name and password 4---- Click Add button and to take effect Add the other cameras in the same way. Click Submit to save. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited wwww.foscam.co ww.foscam.comm Click submit after finishing all settings Return to video window. You will see all of the cameras accessible through the internet. When you are away from home, you can use the first cameras DDNS domain name and port to view all the cameras via internet. Figure 3.12 Figure 3.13 Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 25 25 wwww.foscam.co ww.foscam.comm 3.63.6 Basic Network Settings If you want to set a static IP for the camera, select Basic Network Settings. Keep the camera in the same subnet of your router or computer. Figure 3.14 Changing settings here is the same as using the IP Camera Tool. (Figure 3.17/3.18) It is recommended that you use the subnet mask, gateway and DNS server from your locally attached PC. If you dont know the subnet mask, gateway and DNS server, you can check your computers local area connection as follows:

Control Panel Network Connections Local Area Connections Choose SupportDetails. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 26 26 wwww.foscam.co ww.foscam.comm Figure 3.15 If you dont know the DNS server, you can use the same settings as the Default Gateway. Figure 3.16 Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 27 27 wwww.foscam.co ww.foscam.comm Another way to change the cameras LAN IP and HTTP Port no. Open the IP Camera Tool, select the camera you want to change the port no, right click on the IP address link, and goes to Option Network Configuration, it pops up another dialogue showed as the following screen the camera you want Select to change the LAN IP or port no, right click Figure 3.17 Figure 3.18 IP Address: Fill in the IP address assigned and make sure it is in the same subnet as your computer or router. (I.e. the first three sections are the same) Subnet Mask: The default subnet mask of the equipment in our LAN is: 255.255.255.0.You can find the subnet mask in the basic information of your router or the locally-attached of your PC. Gateway: Make sure it is in the same subnet with PCs IP address. The gateway is your routers LAN IP. DNS Server: IP address of your ISP network provider. You can find the DNS server in your router or check the locally-attached address of your computer. Your PC contains your PCs IP address, gateway and DNS server. Normally, there are two DNS servers. Here you can also set the DNS server the same with gateway. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 28 28 Http Port: The default Lan port is 80.You can set another port number, such as port 8005, 8100.etc. User&Password: Default administrator user name is admin with no password. wwww.foscam.co ww.foscam.comm If the prompt Subnet doesnt match, dbclick to change! appears, please enable DHCP set cameras IP address and gateway once again. 3.73.7 Wireless Wireless Settings Settings Wireless Lan Settings support three modes: Infra(Do wireless lan settings manually) and WPS

(Wi-FI Protected Set-up) and Adhoc.. If your router does not support WPS function,please go to chapter 3.7.1 and make wireless connection settings manually. If your router supports WPS function, please go to chapter 3.7.2 and make wireless connection settings quickly. If there is no wireless router, please go to chapter 3.7.3 and connect the IPCAM directly to a host in a peer_to_peer environment. 3.7.1 Infrastructure Mode Step 01) Please choose Device Management and goes to the option Wireless LAN Settings , click Wireless LAN Settings. Then enable Using Wireless LAN. Click the Scan button and the camera will detect all WIFI devices around the area. It should also display your router in the list. (Figure 3.19) Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 29 29 wwww.foscam.co ww.foscam.comm Click Scan Button to search WIFI device Figure 3.19 Step 02) Click the SSID of your router in the list, the corresponding information (SSID &

Encryption) will be filled in the following boxes automatically. You will only need to fill in the share key. Make sure that SSID, Encryption and share key you filled in for the camera are exactly the same for your router. Click the SSID of router and SSID, Encryption will be filled in the following box automatically Enter the same share key with your router Figure 3.20 Step 03) Please click on the Submit button after all settings have been entered, the camera will reboot. After the camera has completed the reboot process, wait 10 seconds and disconnect the network cable. The LAN IP address will disappear on the window of IP Camera Tool when the camera gets Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 30 30 restarted. Just wait for around 1 minute, the camera will get wireless connection, and the LAN IP of the camera will be showed again on the window of the IP Cam Tool. You have done wireless connection of the camera successfully. If the camera has a dynamic IP, after the wireless settings, the IP will be changed. wwww.foscam.co ww.foscam.comm Note If fail to make WiFi connection, please refer to seller or us for help. 3.7.2 WPS (Wi-Fi Protected Set-up) Step 01) Please press and hold the RESET button for four seconds. Reset Button Step 02) Press the WPS button on your router within 60 seconds. The WPS button is usually on the back or side of your router. On some routers, you may need to log in to the web interface and click on an on-screen button to activate the WPS feature. If you are not sure where the WPS buttons is on your router, please refer to your routers User Manual. The camera will automatically create a secure wireless connection to your router. If you have plugged in the network cable, please plug it out. While connecting, the green network light will blink quickly and the wireless settings will take effect. The IP Camera Tool will search the cameras LAN IP. Make sure the PC and the camera share the same subnet. Note 1 During the WPS Settings, you must press the Reset button only for four seconds, or else, the camera may be reset back to factory default settings if you press and hold on the reset button above 10 seconds. 2 The security mode of router cannot be WEP, or else the WPS settings may be failed. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 31 31 wwww.foscam.co ww.foscam.comm 3.7.3 Adhoc Mode Under this mode, the IPCAM will directly connect to a host in a peer_to_peer environment. Make sure the PC has plugged in the wireless network card. Step 01) Enable wireless and choose Adhoc mode. Fill in a SSID to identify the IPCAM and then set the security mode, you can choose none or others. Click Apply. Figure 3.21 Step 02) Plug out the network cable and the camera will restart. Open the wireless network card of PC and search the wireless network around the area. You can find the SSID you filled for the camera (Figure 3.21). Figure 3.22 Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 32 32 wwww.foscam.co ww.foscam.comm Step 03) Disabled the wired connection of the PC. Select the SSID you filled at Figure3.21 for your camera and enter the same key with your camera. Make sure PC and Camera share the same subnet. Open the IP Camera Tool, you can search the camera LAN IP again. 3.83.8 ADSLADSL Figure 3.23 If you are connecting the camera directly to a ADSL modem, you can do ADSL settings with your ADSL account &password provided by the ISP, then make the camera connected to the network. Enter the ADSL user and password Figure 3.24 Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 33 33 3.93.9 UPnP Settings wwww.foscam.co ww.foscam.comm Figure 3.25 The default UPnP status is closed. You can select the checkbox and open UPnP, then the cameras software will be configured for port forwarding. Back to the Device Status panel, you can see the UPnP status:

There may be issues with your routers security settings, and sometimes may error. We recommend you configure port forwarding manually on your router (Figure 3.30). Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 34 34 wwww.foscam.co ww.foscam.comm 3.10 DDNS Service Settings FOSCAM camera has embedded a unique DDNS domain name when producing, and you can directly use the domain name, you can also use the third party domain name. FOSCAM domain name Here take camera.myfoscam.org for example. Go to option of DDNS Service Settings on the administrator panel, you can see the domain name. Please enable the FOSCAM DDNS name first. Enable DDNS name FOSCAM Figure 3.26 Enable: Open or close the FOSCAM domain name. The default status of FOSCAM domain name is open. Validity Queries: Check the validity of embedded domain name. Now you can use http:// Domain name + HTTP Port to access the camera via internet. Take hostname camera.myfoscam.org and HTTP Port no. 88 for example, the accessing link of the camera via internet would be http:// camera.myfoscam.org:88 Note: If you want to use the manufacturers domain name, please select None as the Third Party DDNS and enable the Manufacturers domain name, then click submit Third Party Domain Name Settings User can also use third part DDNS, such as www.no-ip.com. ,www. dyndns.com Here take www.no-ip.com for example:

Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 35 35 Step 1, Go to the website www.no-ip.com to create a free hostname Firstly: Login on www.no-ip.com and click No-IP Free to register. wwww.foscam.co ww.foscam.comm Click here to register Figure 3.27 Please register an account step by step according to instructions on www.no-ip.com After registration, please login your email which used to register. You will receive an email from website, please click the link to activate your ACCOUNT as indicated in email. Secondly: Login the link with the registered username and password to create your domain name. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 36 36 wwww.foscam.co ww.foscam.comm Figure 3.28 Figure 3.29 Please create the domain name step by step according to instructions on www.no-ip.com Step 2, DO DDNS Service Settings within the Camera Please set DDNS Service Settings within the camera by hostname, a user name and password youve got from www.no-ip.com Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 37 37 wwww.foscam.co ww.foscam.comm Take hostname ycxgwp.no-ip.info, user name foscam, password foscam2012 for example. Firstly, goes to option of DDNS Service Settings on the administrator panel. Secondly, disable the Manufacturers domain name and select No-Ip as a server in the Third Party DDNS. fill foscam as DDNS user, Thirdly, fill ycxgwp.no-ip.info as DDNS domain and server URL, Then click save to make effect. The camera will restart and to take the DDNS settings effective. fill password foscam2012 as DDNS password, login the camera, and go to option of Device Status on the Fourthly, after the restart, administrator panel, and check if the DDNS status is successful. If failed, please double check if you have input the correct hostname, user name, and password, and try to redo the settings. Note The Third Party DDNS and the Manufacturers Domain Name cannot work at the same time. If you have set Third Party DDNS and meanwhile you enabled the Foscam Domain Name, the Third Party DDNS will take effect. Do port forwarding within the router Example: The cameras LAN IP address is http://192.168.1.35:88 , Firstly, login the router, goes to the menu of Port Forwarding or Port Trigger (or named Virtue Server on some brands of router). Take Linksys brand router as an example, Login the router, and goes to Applications & Gaming->Single Port Forwarding. Secondly, Create a new column by LAN IP address & HTTP Port No. of the camera within the router showed as below. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 38 38 wwww.foscam.co ww.foscam.comm Figure 3.30 Use domain name to access the camera via internet After the port forwarding is finished, you can use the domain name+ http no. to access the Take hostname ycxgwp.no-ip.info and http no. 88for example, the camera via internet. accessing link of the camera via internet would be http:// ycxgwp.no-ip.info:88 Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 39 39 wwww.foscam.co ww.foscam.comm 3.11 Mail Service Settings If you want the camera to send emails when motion has been detected, Mail Service Settings will need to be configured. 1 2 3 4 6 5 Figure 3.31 1----- Sender Mailbox for sender must support SMTP 2----- Receiver Mailbox for receiver need not support SMTP,you can set 4 receivers 3----- SMTP Server/ Port Enter SMTP server for sender. SMTP port is usually set as 25. Some SMTP servers have their own port, such as 587 or 465 and Transport Layer Security usually is None. If you use Gmail, Transport Layer Security must be set to TLS or STARTTLS and SMTP Port must be set to 465 or 25 or 587, which port you choose should be decided by which Transport Layer Security you select. 4---- SMTP user 5----Submit Click Submit to take effect 6----Test Click Test to see if SMTP has been successfully configured. ID account of the sender email address NOTE: Click Submit first before choosing Test. Click Test to see if SMTP has been successfully configured. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 40 40 wwww.foscam.co ww.foscam.comm

. Figure 3.32 If the test fails with one of the following errors after clicking Test, verify that the information you entered is correct and again select Test . 1) Cannot connect to the server 2) Network Error. Please try later 3) Server Error 4) Incorrect user or password 5) The sender is denied by the server. Maybe the server need to authenticate the user, please check it and try again 6) The receiver is denied by the server. Maybe because of the anti-spam privacy of the server 7) The message is denied by the server. Maybe because of the anti-spam privacy of the server 8) The server does not support the authentication mode used by the device Report Internet IP by MailIf selected, you will receive emails which contains internet IP information such as When the camera is powered or the Internet IP has changed. (For example:

IPCAM's urls is http://119.123.207.96:8068). Make sure the port is mapped to the router correctly. 3.12 MSN Setting If you want the camera send its current internet IP address to you or your friends, please set MSN settings. Acquire an MSN ID for the IPCAM first, then follow the instructions as per Figure 3.33. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 41 41 wwww.foscam.co ww.foscam.comm Fill in the user and password of the MSN ID you applied for your camera MSN ID in this list can chat with the camera Click Submit and go to the Device Status screen and verify the MSN settings are succeed. Figure 3.33 Figure 3.34 When the MSN ID in the Friends list login the MAN, he can chat with camera. For example:

Foscam13(this account contained in the Friends list) log in MSN, and double click the cameras account (foscam31), then enter url?, the camera will send its current IP address to you. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 42 42 wwww.foscam.co ww.foscam.comm Note: Create a new MSN account for the camera, do not use the same MSN account as you would like to chat with your friends. When the camera login uses the MSN account, this account cannot be used for anything else when the camera works. Figure 3.35 3.13 FTP Service Settings If you want to upload images to your FTP serveryou can set FTP Service Settings. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 43 43 wwww.foscam.co ww.foscam.comm Figure 3.36 Figure 3.37 FTP server: If your FTP server is located on the LAN, you can set as Figure 3.36. If you have an FTP server which you can access on the internet, you can set as Figure 3.37. FTP Port: Usually the port is 21. FTP Upload Folder: Make sure that the folder you plan to store images exists as the camera cant create the folder itself. Also, the folder must be read/writable. FTP Mode: The camera supports standard (POST) mode and passive (PASV) mode Upload Image Now: This option will upload images continuously when you enable the checkbox Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 44 44 wwww.foscam.co ww.foscam.comm Enable Set Filename: When you enable this option the uploaded image will be named according to the filename you enter. The next image will overwrite the filename of the previous image. Hence there will only be one image, the last uploaded. Filename: See the above option. Note: You cannot change the name of the alarm image. Upload Interval refers to the time between the current uploaded. Click Submit to save these settings. Click Test, the following screen displays if successful. image and the next image being Figure 3.38 The following errors may occur:

1) Can not connect to the server. Check if the FTP Server is correct. 2) Network Error. Please try later. 3) Server Error. 4) Incorrect user or password. Check the username and password. 5) Cannot access the folder. Verify the folder exists and your account is authorized 6) Error in PASV mode. Verify the server supports PASV mode. 7) Error in PORT mode. PASV mode should be selected if the device is behind a NAT. 8) Cannot upload file. Verify your account is authorized If an error occurs check the parameters you entered are correct. The filename format of the image is similar to 00606E8C1930(sarah)_0_20100728114350_25.jpg Check if your FTP server supports this file name format. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 45 45 wwww.foscam.co ww.foscam.comm 3.14 Alarm Service Settings IP Camera supports Motion Detection Alarmed, when the motion has been detected, it will send email alerts or upload images or record. 1 2 3 1---- If you want to set Motion Detection Alarmed ,select the checkbox 2---- The larger the number, the higher the motion sensitivity will be 3---- Select this option to reduce false alarms when light changes Figure 3.39 If motion is detected after you enable Motion Detection Armed Detection Alarmed, the Alarm Status will turn to Motion Detect Alarm. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 46 46 wwww.foscam.co ww.foscam.comm Figure 3.40 Here you can see the alarm status There are four alarm indicators:

1) Camera will send emails when motion is activated. If you want to receive images when motion is detected, you must set Mail Service Settings first.

(Figure 3.31) Then set motion alarm as follows:

Figure 3.41 2) Upload images via FTP server when motion trigger. To upload images to an FTP server when motion is detected, you must set FTP Service Settings(Figure 3.36/3.37) first and then set motion alarm as pictured below Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 47 47 wwww.foscam.co ww.foscam.comm Select this option Set an interval for images to upload Figure 3.42 3) You can hear the beep sound when the alarm has been detected. Select this option Figure 3.43 4) The camera will record automatically for one minute after motion is detected. You can find the recording file in the folder which you set previously. (Figure 3.6) Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 48 48 wwww.foscam.co ww.foscam.comm Select the checkbox Figure 3.44 When you enable motion alarm, the camera will record automatically and store the recording file to the folder you configured. This icon is used to control whether the folder opens or not. Alarm Scheduler:

Here are two ways to set the alarm. 1) Alarm at any time when motion is detected. Dont select Scheduler. Click Submit and the camera will alarm at any time when motion is detected. Figure 3.45 Another Way: select Scheduler, and click set All, you will see all time boxes turn blue as in the following picture. Click Submit and the camera will alarm at any time when motion is detected. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 49 49 wwww.foscam.co ww.foscam.comm Figure 3.46 2) Specify an alarm schedule. If you want the camera to alarm during set times select Scheduler and set time range. If you want to select one serial area, you can click any number between 00 and 23 on the first row, the corresponding column will be selected and it will turn blue. For example, click the number 06 on the first row, you can see the column turn blue. That means the camera will alarm when motion is detected between 6 and 7 oclock every day. Click the number06 on the second row, you can cancel the corresponding column you set. And it will turn grey. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 50 50 wwww.foscam.co ww.foscam.comm Figure 3.47 If you want to select discrete area, you click the left button on the box of time range. It will turn blue. If you want to delete it, just click the left button and it will turn grey. Figure 3.48 Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 51 51 wwww.foscam.co ww.foscam.comm 3.15 PT Settings You can set pan/tilt speed. Normally, PT speed is 3. The larger the setting number, the lower speed. Dont enable the checkbox disable preset if you want to use the function of preset, it will be effective after you reboot device. Figure 3.49 the round between 1 and 10, Patrol rounds horizontal: Set then click Submit. Back to surveillance window. Click the Horizon patrol button, the rounds horizontally you set and then stop if you dont click Stop horizon patrol button. For example, you set 4 for the patrol rounds. Click submit and back to surveillance window. Click the Horizon patrol button and do not click the Stop horizon patrol button, the camera will patrol 4 rounds and then stop automatically. the camera will patrol Patrol rounds vertical: Set the round between 1 and 10, then click submit. Back to surveillance window Click the Vertical patrol button, the camera will patrol the rounds vertically you set and then stop if you dont click Stop vertical patrol button. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 52 52 wwww.foscam.co ww.foscam.comm 3.16 Upgrade Device Firmware When you upgrade the camera, please upgrade system firmware first and then upgrade the Web UI. Upgrade firmware system Upgrade Web UI Figure 3.50 Click Browse, choose the correct bin file and then click Submit to upgrade. Dont shut down the power during upgrade until the IP camera tool finds the camera again. Upgrade Firmware by IP Camera Tool Double click the IP Camera Tool shot icon

, select the Camera IP that you want to upgrade the firmware. Then select Upgrade Firmware and enter the username and password, choose the firmware file, and upgrade. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 53 53 wwww.foscam.co ww.foscam.comm Figure 3.51 Enter the User name and password Figure 3.52 CAUTION: If your camera works well with the current firmware, we recommend not upgrading. Please dont upgrade the firmware unnecessarily. Your camera may be damaged if misconfigured during an upgrade. NOTE:

1) Please ensure you have download the correct firmware package for your camera before upgrading. Read the upgrade documentation (readme.txt file) in the upgrade package before you upgrade. 2)Upon downloading the firmware check the sizes of the .bin files. They must match the size in the readme.txt file. If not, please download the firmware again until the sizes are the same. Your camera will not function correctly if a corrupt .bin file is used. 3) Normally, only Device WEB UI need to be upgrade, please do not try to upgrade the Device Firmware. 4) Never shut down the power of the camera during upgrade until the IP camera restart and get connected. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 54 54 wwww.foscam.co ww.foscam.comm 3.17 Backup & Restore Settings Click Submit to save all the parameters you have set. These parameters will be stored in a bin file for future use. The bin file can be reloaded to restore the parameters that were set. Click Submit parameters to store Figure 3.53 Load the parameters bin file 3.18 Restore Factory Settings All parameters will return to factory settings if selected. 1 2 Figure 3.54 Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 55 55 wwww.foscam.co ww.foscam.comm 3.19 Reboot Device Click Reboot Device to reboot the camera. This is similar to unplugging the power to the camera. 3.20 Log The log record shows who accessed the camera and when. (Figure 3.55). Figure 3.55 3.21 Back This will take you back to the surveillance window. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 56 56 wwww.foscam.co ww.foscam.comm 44 APPENDIX APPENDIX 4.1 Frequently Asked Questions NOTE: Always verify network connections are working by checking the status of the indicators on the network server, hub and network card. 4.1.1 I have forgoten the administrator username and/or password To reset the administrator username and password, press and hold down the RESET BUTTON for 10 seconds. Upon releasing the reset button, the username and password will return to the factory default administrator username and password. Please power on the camera before reset Default administrator username: admin Default administrator password: No password 4.1.2 Subnet doesnt match, dbclick to change If the IP Camera Tool shows the error Subnet doesnt match, dbclick to change!, select Obtain IP from DHCP server. If this error still exists after obtaining an IP from the DHCP server, check the local area connection of your computer and verify the subnet and gateway of the camera which should be the same subnet of your computer. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 57 57 wwww.foscam.co ww.foscam.comm 4.1.3 No Pictures Problems Video streaming is managed by the ActiveX controller. If the ActiveX controller isnt installed correctly you will see no video image. There are two ways to resolve this problem:

1) Reinstall IP Camera Tool and ActiveX controllerrecommended. 2) Download ActiveX controller and set the security setting of IE: IE browserToolInternet ProperSecurityCustom LevelActiveX control and Plug-ins. The first three options of front should be set to be Enable, The ActiveX programs read by the computer will be stored. As follows:

Enable: Download unsigned ActiveX controls Enable: Initialise and script ActiveX controls not marked as safe Enable: Run ActiveX controls and plug-ins If you allow the ActiveX to run, but still can not see living video and a red cross in the centre of the video. Please select another port number. Dont use port 80, use port 85, 8005.etc. Figure 5.1 Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 58 58 wwww.foscam.co ww.foscam.comm Change another port number NOTE: Make sure that your firewall or anti-virus software does not block the camera or ActiveX. If you cannot see live video, try shutting down the firewall or anti-virus software and try again. Figure 5.2 4.1.4 Cant access IP camera on internet Possible reasons why camera is not accessible on the internet:

1) ActiveX controller is not installed correctly 2) The port which the camera uses is blocked by a Firewall or Anti-virus software. Try changing to another port number. (Figure 5.2) 3) Port forwarding is not successful (Figure 3.30) Double check these settings and make sure they are correct. 4.1.5 IP Camera Tool could not find cameras IP Verify that the network cable is securely fastened to the camera. Make sure that DHCP is enabled on your router, do not enable MAC address filter. Make sure that the firewall or anti-virus software does not block the camera. You can add the camera as a trusted site on your firewall or anti-virus software. 4.1.6 UPnP always failed UPnP only contains port forwarding in our recent software. Sometimes, it may be fail to do port forwarding automatically because of the firewall or anti-virus software. It may also be due to the routers security settings. We recommend manually configuring port forwarding the camera can be viewed on the internet. Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 59 59 wwww.foscam.co ww.foscam.comm 4.1.7 Couldnt find the shortcut on the desktop after install IP camera tool If you use Windows7 or Vista and the shortcut is missing after installing the IP camera tool, check the path of IP Camera program. For example, if it was pointing to C:\Windows\System32\IPCamera.exe. Please fix this by pointing the shortcut to the correct path C:\Windows\SysWOW64\IPCamera.exe. After this you should be able to use the shortcut without any problems. 4.1.8 I cant change the record path When you use Windows7 or Vista, you may be not able to change the record path because of the security settings of computer. Please add the camera as a trusted site to resolve this issue. The steps are IE browserToolInternet PropertiesSecurityTrusted sitesSitesAdd 4.1.9 I cant find multi-device settings and record icon Record and multi-device functionality are controlled by the ActiveX controller. These functions are not available in Firefox, Google Chrome and Safari. 4.1.10 Camera cannot connect using wireless If your camera cannot connect wirelessly after you set the wireless settings, unplug / plug the power cable. (for more details: Wireless LAN settings in chapter 3.7) Usually, camera cant connect wireless mainly because of incorrect settings. Verify that the SSID is correct; use the same encryption for router and camera. Share key should not contain special characters, only word and number will be better. Disable MAC address filtering. 4.1.11 Cant see other cameras listed in multi-device when using remote access If you want to view all the cameras via the WAN, verify that each camera added in the multi-device settings can be accessed by using the DDNS name and port number. Use the DDNS domain name not the cameras LAN IP. (For more details see: How to add cameras in WAN) Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 60 60 wwww.foscam.co ww.foscam.comm 4.1.12 Only see black screen or undefined characters when using remote login If you could access the login page remotely, this indicates that your DDNS settings are correct. If you are unable to see live video but only some undefined characters, this may be due to the internet speed issues or the camera using Wi-Fi. 4.2 Default Parameters Default network Parameters IP address: obtain dynamically Subnet mask: 255.255.255.0 Gateway: obtain dynamically DHCP: Disabled DDNS: Embedded FOSCAM domain name Username and password Default administrator username: admin Default administrator password: No password 4.3 Specifications ITEMS Image Sensor Lens Video Image Sensor Display Resolution Lens Mini. Illumination Lens Type IR_CUT Viewing angle Image Compression Image Frame Rate Resolution Flip Mirror Images Light Frequency Video Parameters FI8919W Color CMOS Sensor 640 x 480 Pixels(300k Pixels) f: 4mm 2Lux Glass Lens Filter will switch automatically 40 degrees MJPEG 15fps(VGA),30fps(QVGA) 640 x 480(VGA), 320 x 240(QVGA) Vertical / Horizontal 50Hz, 60Hz or Outdoor Brightness, Contrast Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 61 61 wwww.foscam.co ww.foscam.comm Communication Power Environment Ethernet Supported Protocol Wireless Standard Data Rate Wireless Security Infrared Light Dimension Gross Weight Net Weight Power Supply Power Consumption Operate Temper. Operating Humidity Storage Temper. Storage Humidity PC Requirements CPU Memory Size Display Card Supported OS Browser Certification CE,FCC One 10/100Mbps RJ-45 HTTP,FTP,TCP/IP,UDP,SMTP,DHCP,PPPoE,DDNS,UPnP,GP RS IEEE 802.11b/g/n 802.11b: 11Mbps(Max.) 802.11g: 54Mbps(Max.) 802.11n: 150Mbps(Max.) WEP & WPA & WPA2 Encryption 22 IR LEDs, Night visibility up to 15 meters 127(L) x212(W) x230mm(H) 2150gColor Box Size: 314 x271 x162mm 1535g DC 12V/2.0A (EU,US,AU adapter or other types optional) 13.5Watts (Max.) 0 ~ 55C (32F ~ 131F) 20% ~ 85% non-condensing

-10C ~ 60 (14F ~ 140F) 0% ~ 90% non-condensing 2.0GHZ or above 256MB or above 64M or above Microsoft Windows 2000/XP/Vista/Windows7-32bit/Windows7-

64bit/Windows8- 32bit/Windows8-64 bit / mac IE 6.0, Chrome, Safari or other standard browsers IE8.0,IE9.0, Firefox2.0,Firefox3.0, Google IE7.0, 55 OBTAINING OBTAINING TECHNICAL TECHNICAL SUPPORT SUPPORT While we hope your experience with the IPCAM network camera is enjoyable and easy to use, you may experience some issues or have questions that this Users Guide has not answered. If you have problem with FOSCAM IP camera, please first contact FOSCAM reseller for solving the problems. If our reseller cannot provide service, pls contact our service department:

tech@foscam.com . Shenzhen Foscam Shenzhen Tel:Tel: 8686 755755 2674 Foscam Intelligent 2674 5668 5668 Fax:Fax: 8686 755755 2674 2674 5168 5168 Intelligent Technology Technology Co.,Co., Limited Limited 62 62 Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. RF exposure warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. 25