The user manual of WIFIBluetooth module 1. The product description TheusercanachievewirelessconnectiontoWIFInetandBluetooth,throughthismodule 2. Basic parameters Feature Description Feature Description Model Product Name Major Chipset MHCWBT1PIB 2.4GHz WIFI+Bluetooth dualmode module RTL8723DS WLAN Standard IEEE 802.11b/g/n BT Standard BT2.1/4.2v4.2 BR/EDRv4.0 BLE WLAN Frequency Range 2.4GHz~2.4835GHz BT Frequency Range 2402MHz~2480MHz Spread Spectrum IEEE 802.11b: DSSS (Direct Sequence Spread Spectrum) IEEE802.11g/n: OFDM (Orthogonal Frequency Division Multiplexing) Modulation Method DBPSK/DQPSK/CCK(DSSS)BPSK/QPSK/16QAM/64QAM(OFDM) Data Transfer Rate 11b:1,2,5.5, 11Mbps 11g: 6,9,12,18,24,36,48,54Mbps 11n:HT20MCS0~HT20MCS7 HT40MCS0~HT40MCS7 Antenna Reference MHCWBT1PIB:WIFI/BT external ANT Interface SDIO1.1/2.0,HSUART Supply Voltage 3.3V0.3V Dimension 18mm*20mm*2.5mm Operating Temperature 0C to 70C Storage Temperature 40C to 125C RF output power Band Limited Power(dBm) BT WLAN 2402MHz2480MHz 2412MHz2472MHz 020
<20 3. The display method of Model approved code In the factorythe model approve code is lasered on the shielding case. 4. FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Low Temperature Operation When the external temperature is lower than 0, the IC may be damaged to a certain extent, which will affect the operation of the module. Please ensure that the operation temperature meets the requirements. FCC ID: 2AFZZMHCWBT1PIB 5. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of FCC RF Rules. This equipment should be installed and operated with minimum distance of 20 in (50cm)between the radiator and yourbody. This transmitter must not be colocated or operated in conjunction with any other antenna or transmitter CAUTION:
To comply with the limits of the Class B digital device pursuant to Part 15 of the FCC Rules, this device is compliant with Class B limits. All peripherals must be shielded and grounded. Operation with noncertified peripherals or nonshielded cables may results in interference to radio or reception MODIFICATION To assure continued compliance, Any changes or modifications not expressly approved by the grantee of this device could void the users authority to operate the device. 5. Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 50 cm(8 in )between the radiator and your body NOTE To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product Contains Transmitter module FCC ID: *******
To satisfy IESD exterior labeling requirements, the following text must be placed on the exterior of the end product " Contains Transmitter module IC: *******
Manufacturer: Xiaomi Communications Co.,Ltd. Address: #019,9th Floor, Building 6, 33 Xierqi Middle Road, Haidian District,Beijing, 100085 China A voltage stabilizing element or circuit is required on the power supplies to the module, and then the power supply is sent to the module This equipment may be operated in all European countries.