FCC ID: 2AFZZK7BNY Mobile Phone (LTE/WCDMA/GSM/BT/WIFI/NFC)

Redmi Note 10S Quick Start Guide 02 48 SAT. 16 AUG. Volume Buttons Power Button USB Type-C Port 1 EN Thank you for choosing Redmi Note 10S Long press the power button to turn on the device. Follow the on-screen instructions to configure the device. For more information, visit our official website:

www.mi.com/global/service/userguide MIUI Redmi Note 10S comes pre-installed with MIUI, our customized Android-

based OS which provides frequent updates and user-friendly features based on suggestions from over 200 million active users worldwide. For more information, please visit en.miui.com SIM Card Tray:

Nano-SIM Nano-SIM Micro SD About Dual SIM:

Dual 4G SIM is offered by select telecom operators and may not be available in all regions. Supports dual nano-SIM cards. When using both SIM card slots, either card can be set as the primary card. VoLTE is only supported by telecom operators in certain regions. System may be automatically updated for optimal network performance. For details, please refer to the system version in use on the device. Please do not insert non-standard SIM cards into the SIM card slot. They may damage the SIM card slot. WARNING: Do not disassemble this device. 2 WEEE Special precautions must be taken to safely dispose of this product. This marking indicates that this product may not be discarded with other household waste in the EU. To prevent harm to the environment or human health from inappropriate waste disposal, and to promote sustainable reuse of material resources, please recycle responsibly. To safely recycle your device, please use return and collection systems or contact the retailer where the device was originally purchased. To view our Environmental Declaration, please refer to the following link:

www.mi.com/en/about/environment CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO INSTRUCTIONS. To prevent possible hearing damage, do not listen at high volume levels for long periods. Additional safety information and precautions can be accessed at the following link: www.mi.com/en/certification Important Safety Information Read all safety information below before using your device:

Use of unauthorized cables, power adapters, or batteries can cause fire, explosion, or pose other risks. Use only authorized accessories which are compatible with your device. This devices operating temperature range is 0C to 40C. Using this device in an environment outside of this temperature range may damage the device. If your device is provided with a built-in battery, to avoid damaging the battery or the device, do not attempt to replace the battery yourself. Charge this device only with the included or authorized cable and power adapter. Using other adapters may cause fire, electric shock, and damage the device and the adapter. After charging is complete, disconnect the adapter from both the device and the power outlet. Do not charge the device for more than 12 hours. The battery must be recycled or disposed of separately from household waste. Mishandling the battery may cause fire or explosion. Dispose of or recycle the device, its battery, and accessories according to your local regulations. Do not disassemble, hit, crush, or burn the battery. If the battery appears deformed or damaged, stop using it immediately.

- Do not short circuit the battery, as this may cause overheating, burns, or other injury.

- Do not place the battery in a high-temperature environment. 3 EN - Overheating may cause explosion.

- Do not disassemble, hit, or crush the battery, as this may cause the battery to leak, overheat, or explode.

- Do not burn the battery, as this may cause fire or explosion.

- If the battery appears deformed or damaged, stop using it immediately. User shall not remove or alter the battery. Removal or repair of the battery shall only be done by an authorized repair center of the manufacturer. Keep your device dry. Do not try to repair the device yourself. If any part of the device does not work properly, contact Mi customer support or bring your device to an authorized repair center. Connect other devices according to their instruction manuals. Do not connect incompatible devices to this device. For AC/DC adapters, the socket-outlet shall be installed near the equipment and shall be easily accessible. Safety Precautions Observe all applicable laws and rules restricting use of mobile phones in specific situations and environments. Do not use your phone at petrol stations or in any explosive atmosphere or potentially explosive environment, including fueling areas, below decks on boats, fuel or chemical transfer or storage facilities, or areas where the air may contain chemicals or particles such as grain, dust, or metal powders. Obey all posted signs to turn off wireless devices such as your phone or other radio equipment. Turn off your mobile phone or wireless device when in a blasting area or in areas requiring two-way radios or electronic devices to be turned off to prevent potential hazards. Do not use your phone in hospital operating rooms, emergency rooms, or intensive care units. Always comply with all rules and regulations of hospitals and health centers. If you have a medical device, please consult your doctor and the device manufacturer to determine whether your phone may interfere with the devices operation. To avoid potential interference with a pacemaker, always maintain a minimum distance of 15 cm between your mobile phone and the pacemaker. This can be done by using your phone on the ear opposite to your pacemaker and not carrying your phone in a breast pocket. To avoid interference with medical equipment, do not use your phone near hearing aids, cochlear implants, or other similar devices. Observe all aircraft safety regulations and turn off your phone on board aircraft when required. When driving a vehicle, use your phone in accordance with relevant traffic laws and regulations. To avoid being struck by lightning, do not use your phone outdoors during thunderstorms. Do not use your phone to make calls while it is charging. Do not use your phone in places with high humidity, such as bathrooms. Doing so may result in electric shock, injury, fire, and charger damage. 4 Security Statement Please update your phones operating system using the built-in software update feature, or visit any of our authorized service outlets. Updating software through other means may damage the device or result in data loss, security issues, and other risks. EU Regulations RED Declaration of Conformity Xiaomi Communications Co., Ltd. hereby declares that this GSM / GPRS /

EDGE / UMTS / LTE Digital Mobile Phone with Bluetooth and Wi-Fi M2101K7BNY is in compliance with the essential requirements and other relevant provisions of the RE Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:

www.mi.com/en/certification RF Exposure Information (SAR) This device is in compliance with Specific Absorption Rate (SAR) limits for general population/uncontrolled exposure (Localized 10-gram SAR for head and trunk, limit: 2.0W/kg) specified in Council Recommendation 1999/519/EC, ICNIRP Guidelines, and RED (Directive 2014/53/EU). During SAR testing, this device was set to transmit at its highest certified power level in all tested frequency bands and placed in positions that simulate RF exposure during use against the head with no separation and near the body with a separation of 5 mm. SAR compliance for body operation is based on a separation distance of 5 mm between the unit and the human body. This device should be carried at least 5 mm away from the body to ensure RF exposure level is compliant or lower than the reported level. When attaching the device near the body, a belt clip or holster should be used which does not contain metallic components and allows a separation of at least 5 mm to be maintained between the device and the body. RF exposure compliance was not tested or certified with any accessory containing metal worn on the body, and use of such an accessory should be avoided. Certification Information (Highest SAR) SAR 10 g limit: 2.0 W/Kg, SAR Value: Head: 0.597 W/Kg, Body: 0.870 W/Kg (5 mm distance). Legal Information This device may be operated in all member states of the EU. Observe national and local regulations where the device is used. This device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range in the following countries:

5 EN BE BG FI LV RO FR LT SK AT EE IT PT IS HR DE CY EL CZ HU LU MT NL DK IE PL SI SE UK(NI) ES TR LI NO CH Restrictions in the 2.4 GHz band:

Norway: This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-lesund. Receiver Category 2 Ensure the power adapter used meets the requirements of Clause 6.4.5 in IEC/EN 62368-1 and has been tested and approved according to national or local standards. Frequency Bands and Power This mobile phone offers the following frequency bands in EU areas only and maximum radio-frequency power:

GSM 900: 35.5 dBm GSM 1800: 32.5 dBm WCDMA 900/2100: 25.7 dBm LTE band 1/3/7/8/20/28/38/40: 25.7 dBm Bluetooth: 20 dBm Wi-Fi 2.4 GHz band: 20 dBm Wi-Fi 5 GHz: 5150 to 5250MHz: 23 dBm, 5250 to 5350 MHz: 23 dBm, 5470 to 5725 MHz: 23 dBm, 5725 to 5850 MHz: 14 dBm NFC: 13.56 MHz < 42 dBuA/m at 10m FCC Regulations This mobile phone complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This mobile phone has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver. 6

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information (SAR) This device meets the governments requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy. The exposure standard for wireless devices employs a unit of measurement known as Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/Kg. For body-worn operation, this device has been tested and meets the FCC RF exposure guidelines for use with an accessory that contains no metal and positions the device a minimum of 1.5 cm from the body. RF exposure compliance with any body-worn accessory that contains metal was not tested and certified, and use of such body-worn accessory should be avoided. Any accessory used with this device for body-worn operation must keep the device a minimum of 1.5 cm away from the body. FCC Note Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits. E-label This device has an electronic label for certification information. To access it, please go to Settings > About phone > Certification, or open Settings and type Certification into the search bar. Model: M2101K7BNY 2101 indicates that this product will be launched after 202101. Disclaimer This user guide is published by Xiaomi or its local affiliated company. Improvements and changes to this user guide necessitated by typographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made by Xiaomi at any time and without notice. Such changes will, however, be incorporated into new online editions of the user guide (please see details at www.mi.com/global/service/userguide). All illustrations are for illustration purposes only and may not accurately depict the actual device. This smartphone is designed with Corning Gorilla Glass 3. 7 EN Manufacturer: Xiaomi Communications Co., Ltd. Manufacturer postal address:

#019, 9th Floor, Building 6, 33 Xierqi Middle Road, Haidian District, Beijing, China, 100085 Brand: Redmi Model: M2101K7BNY Xiaomi Inc. All rights reserved. 8

Xiaomi Communications Co., Ltd. POWER OF ATTORNEY DATE: 03/12/2021 To:

Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 We, the undersigned, hereby authorize TA Technology (Shanghai) Co., Ltd.

/Liu Mengting on our behalf, to apply to FCC on our equipment for FCC ID:

2AFZZK7BNY. Any and all acts carried out by TA Technology (Shanghai) Co., Ltd. / Liu Mengting on our behalf shall have the same effect as acts of our own. Sincerely, Signature:

Print name: shenghao Company: Xiaomi Communications Co., Ltd.

Xiaomi Communications Co., Ltd. UNII Declaration Letter We have declared below featured for FCC equipment authorization, device FCC ID: 2AFZZK7BNY

(1) DFS Device --

Master, Client without radar detection capability, Client with Radar detection capability , N/A

(2) Active / Passive Scanning , adhoc mode access point capability passive scanning

(where the device is can listen only with no probes) Yes, Yes, Yes, Yes, Yes, No No No No No Ad Hoc Mode capability Access point capability Yes, Yes, Yes, Yes, Yes, No No No No No Yes, Yes, Yes, Yes, Yes, No No No No No Frequency Band

(MHz) Active Scanning

(the device can transmit a probe

(beacon)) 2412 2462 MHz 5150 5250 MHz 5250 5350 MHz 5470 5725 MHz 5725 5850 MHz Yes, Yes, Yes, Yes, Yes, No No No No No

(3) Country code selection ability -

If no, pls explain how was implemented :

(4) Meet 15.202 requirement -

pls check below :

Yes , No , Yes , No A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network.

(5) For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes can not be modified by end user or an installer. No Apply , Apply ,

(If apply , pls help to provide explanation on how it was implement (By hardware or software , and how software was controlled) If you have any questions, please feel free to contact me at the address shown below. Yours sincerely, Signatory Printed Name: shenghao Position: Certification Director

Xiaomi Communications Co., Ltd. Request for Confidentiality Date: _2021-03-12_ Subject: Confidentiality Request for: _____ FCC ID: 2AFZZK7BNY ______ Pursuant to FCC 47 CRF 0.457(d) and 0.459 the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent*1 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent*

Users Manual

*Note: ______(Insert Explanation as Necessary)______ ______ Xiaomi Communications Co., Ltd._____ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of __180_ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TCB in the event information regarding the product or the product is made available to the public. TCB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, Xiaomi Communications Co., Ltd. By:

shenghao

(Signature/Title2)

(Print name)