FCC ID: UZ7MPACTINDR1 2AA Beacon

MPACT LOCATION & ANALYTICS HARDWARE INSTALLATION GUIDE VERSION 1.0 RB BEACON ATLS-T1B 2AA BEACON MPACT-INDR1 USB BEACON MPACT-USB1 TABLE OF CONTENTS Chapter 1 MPact Bluetooth Smart beacon Overview Chapter 2 Beacon Hardware Specifications and Installation 2.1 RB Beacon Part Number: MPACT-T1B20-000-WR ........................................................................................................2-1 2.1.1 Installing the Tie-Wrap Style Beacon ..................................................................................................................2-1 2.2 RB Beacon Part Number: MPACT-T1B10-000-WR ........................................................................................................2-2 2.2.1 Installing the Universal Style Beacon ..................................................................................................................2-3 2.3 2AA Beacon Part Number: MPACT-MB2000-01-WR ....................................................................................................2-4 2.3.1 Installing the Indoor Style Beacon .......................................................................................................................2-5 2.4 USB Beacon Part Number: MPACT-MB3000-01-WR ....................................................................................................2-6 2.4.1 Installing the USB Style Beacon ..........................................................................................................................2-6 2.4.2 Beacon Battery Replacement ..............................................................................................................................2-7 2.4.3 Replacing RB Battery: MPACT-T1B20-000-WR and MPACT-T1B10-000-WR .....................................................2-7 2.4.4 Replacing 2AA Battery: MPACT-MB2000-01-WR ...............................................................................................2-8 Appendix A Customer Support 4 MPact Location & Analytics Hardware Installation Guide ABOUT THIS GUIDE This chapter is organized into the following sections:

Using the Documentation

Zebra Technologies Corporation ("Zebra") End-User Software License Agreement 6 Using the Documentation The following sections provide information about the document and notational conventions used in the guides, and provides a list of related documentation. Document Conventions The following conventions are used in this manual to draw your attention to important information:

NOTE: Indicates tips or special requirements.

!

CAUTION: Indicates conditions that can cause equipment damage or data loss. WARNING! Indicates a condition or procedure that could result in personal injury or equipment damage. Revision History This guide has the following release and revision milestone history:

Release Date Revision A June, 2015 Change Initial release of document with new MPact beacons added. About this Guide 7 Notational Conventions The following notational conventions are used in this document:

Italics are used to highlight specific items in the general text, and to identify chapters and sections in this and related documents

Bullets () indicate:

lists of alternatives

lists of required steps that are not necessarily sequential

action items

Sequential lists (those describing step-by-step procedures) appear as numbered lists Related Documentation MPact Location and Analytics documentation includes the following:

MPact Location & Analytics Deployment Guide

MPact Location & Analytics Server Reference Guide

MPact Location & Analytics Server API Guide

MPact Location & Analytics Toolbox Reference Guide

MPact Location & Analytics Client Software Development Kit 8 Zebra Technologies Corporation ("Zebra") End-User Software License Agreement BY INSTALLING AND/OR USING THIS PRODUCT, YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UNDERSTAND IT AND AGREE TO BE BOUND ITS TERMS. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, ZEBRA IS NOT WILLING TO LICENSE THE PRODUCT TO YOU, AND YOU MUST NOT INSTALL OR USE THIS PRODUCT. Definitions Grant of License Zebra Technologies Corporation ("Zebra") grants you ("Licensee" or "you") a personal, nonexclusive, nontransferable, revocable, nonassignable, limited license to use the software and documentation ("Product(s)") subject to the terms and conditions of this Agreement. You shall use the Products only for your internal business purposes, exclusively to support Zebra devices. Any use of the Products outside of the conditions set forth herein is strictly prohibited and will be deemed a breach of this Agreement resulting in immediate termination of your License. In the event of a breach of this Agreement, Zebra will be entitled to all available remedies at law or in equity (including immediate termination of the license without notice, immediate injunctive relief and repossession of all Products unless Licensee is a Federal agency of the United States Government). You shall not distribute, sublicense, rent, loan, lease, export, re-export, resell, ship or divert or cause to be exported, re-

exported, resold, shipped or diverted, directly or indirectly, the Products under this Agreement. You shall not, and shall not permit others to: (i) modify, translate, decompile, bootleg, reverse engineer, disassemble, or extract the inner workings of the Products, (ii) copy the look-and-feel or functionality of the Products; (iii) remove any proprietary notices, marks, labels, or logos from the Products; (iv) rent or transfer all or some of the Products to any other party without Zebra's prior written consent; or

(v) utilize any computer software or hardware which is designed to defeat any copy protection device, should the Products be equipped with such a protection device. Title to all copies of Products will not pass to Licensee at any time and remains vested exclusively in Zebra. All intellectual property developed, originated, or prepared by Zebra in connection with the Products remain vested exclusively in Zebra, and this Agreement does not grant to Licensee any intellectual property rights. Portions of the Products are protected by United States patent and copyright laws, international treaty provisions, and other applicable laws. Therefore, you must treat the Products like any other copyrighted material (e.g., a book or musical recording) except that you may make one copy of the Product solely for back-up purposes. Unauthorized duplication of the Products constitutes copyright infringement, and in the United States is punishable in federal court by fine and imprisonment. Limited Warranty Zebra warrants for a period of ninety (90) days from your receipt of the Products to you that the Software, under normal use, will perform substantially in accordance with Zebra's published specifications for that release level of the Software. The written materials are provided "AS IS" and without warranty of any kind. Zebra's entire liability and your sole and exclusive remedy for any breach of the foregoing limited warranty will be, at Zebra's option, the provision of a downloadable patch or replacement code, or a refund of the unused portion of your bargained for contractual benefit up to the amount paid for the Products. Disclaimer THIS LIMITED WARRANTY IS THE ONLY WARRANTY PROVIDED BY ZEBRA, AND ZEBRA MAKES, AND YOU RECEIVE, NO OTHER WARRANTIES OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR IN ANY COMMUNICATION WITH YOU. ZEBRA SPECIFICALLY DISCLAIMS ANY WARRANTY INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILTY, NONINFRINGEMENT, OR FITNESS FOR A PARTICULAR PURPOSE. ZEBRA DOES NOT WARRANT THAT THE PRODUCTS WILL MEET YOUR REQUIREMENTS, OR THAT THE OPERATION OF THE PRODUCTS WILL BE UNINTERRUPTED OR ERROR FREE, OR THAT DEFECTS IN THE PRODUCTS WILL BE CORRECTED. ZEBRA MAKES NO WARRANTY WITH RESPECT TO THE About this Guide 9 CORRECTNESS, ACCURACY, OR RELIABILITY OF THE PRODUCTS. Some jurisdictions do not allow the exclusion of implied warranties, so the above exclusion may not apply to you. Limitation of Liability THE TOTAL LIABILITY OF ZEBRA UNDER THIS AGREEMENT FOR DAMAGES SHALL NOT EXCEED THE FAIR MARKET VALUE OF THE PRODUCTS LICENSED UNDER THIS AGREEMENT. IN NO EVENT WILL ZEBRA BE LIABLE IN ANY WAY FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL OR PUNITIVE DAMAGES OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST BUSINESS PROFITS, OR LIABILITY OR INJURY TO THIRD PERSONS, WHETHER FORESEEABLE OR NOT, REGARDLESS OF WHETHER ZEBRA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some jurisdictions do not permit limitations of liability for incidental or consequential damages, so the above exclusions may not apply to you. This Limitation of Liability provision survives the termination of this Agreement and applies notwithstanding any contrary provision in this Agreement. Licensee must bring any action under this Agreement within one (1) year after the cause of action arises. Maintenance Unless provided for in a separate agreement, Zebra shall not be responsible for maintenance or field service of the Products. High Risk Activities The Products are not fault-tolerant and are not designed, manufactured or intended for use or resale as on-line control software in hazardous environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, direct life support machines, or weapons systems, in which the failure of the Products could lead directly to death, personal injury, or severe physical or environmental damage ("High Risk Activities"). Zebra and its suppliers specifically disclaim any express or implied warranty of fitness for High Risk Activities, and if you elect to use the Products in any High Risk Activities, you agree to indemnify, defend, and hold Zebra harmless from and against any and all costs, damages, and losses related to that use. U.S. Government If you are acquiring the Products on behalf of any unit or agency of the U.S. Government, the following shall apply. Use, duplication, or disclosure of the Products is subject to the restrictions set forth in subparagraphs (c) (1) and (2) of the Commercial Computer Software - Restricted Rights clause at FAR 52.227-19 (JUNE 1987), if applicable, unless being provided to the Department of Defense. If being provided to the Department of Defense, use, duplication, or disclosure of the Products is subject to the restricted rights set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 (OCT 1988), if applicable. Products may or may not include a Restricted Rights notice, or other notice referring specifically to the terms and conditions of this Agreement. The terms and conditions of this Agreement shall each continue to apply, but only to the extent that such terms and conditions are not inconsistent with the rights provided to you under the aforementioned provisions of the FAR and DFARS, as applicable to the particular procuring agency and procurement transaction. Assignment Except as otherwise provided in this section, neither party may assign this Agreement, or any of its rights or obligations under this Agreement, without the prior written approval of the other party, which will not be unreasonably withheld. Any attempted assignment, delegation, or transfer without the necessary approval will be void. Notwithstanding the foregoing, for any Zebra acquisition, merger, consolidation, reorganization, or similar transaction, or any spin-off, divestiture, or other separation of a Zebra business, Zebra may, without the prior written consent of the other party: (i) assign its rights and obligations under this Agreement, in whole or in part, or (ii) split and assign its rights and obligations under this Agreement so as to retain the benefits of this Agreement for both Zebra and the assignee entity(ies) (and their respective Affiliates) following the split. 10 Governing Law This Agreement shall be governed by the laws of the United States of America to the extent that they apply and otherwise by the laws of the State of New York without regard to its conflict of laws provisions or by the internal substantive laws of the country to which the Products is shipped if end-user customer is a sovereign governmental entity. The terms of the U.N. Convention on Contracts for the International Sale of Goods do not apply. In the event that the Uniform Computer information Transaction Act, any version of this Act, or a substantially similar law (collectively "UCITA") becomes applicable to a Party's performance under this Agreement, UCITA does not govern any aspect of this End User License Agreement or any license granted under this End-User License Agreement, or any of the parties' rights or obligations under this End User License Agreement. The governing law will be that in effect prior to the applicability of UCITA. Compliance with Laws Licensee will comply with all applicable laws and regulations, including export laws and regulations of the United States. Licensee will not, without the prior authorization of Zebra and the appropriate governmental authority of the United States, in any form export or re-export, sell or resell, ship or reship, or divert, through direct or indirect means, any item or technical data or direct or indirect products sold or otherwise furnished to any person within any territory for which the United States Government or any of its agencies at the time of the action, requires an export license or other governmental approval. Violation of this provision will be a material breach of this Agreement, permitting immediate termination by Zebra. Third Party Software The Products may contain one or more items of Third-Party Software. The terms of this Agreement govern your use of any Third-

Party Software UNLESS A SEPARATE THIRD-PARTY SOFTWARE LICENSE IS INCLUDED, IN WHICH CASE YOUR USE OF THE THIRD-PARTY SOFTWARE WILL THEN BE GOVERNED BY THE SEPARATE THIRD-PARTY LICENSE. Open Source Software The Products may contain one or more items of Open Source Software. Open Source Software is software covered by a publicly available license governed solely under Copyright law, whereas the complete terms and obligations of such license attach to a licensee solely through the act of copying, using and/or distribution of the licensed software, such obligations often include one or more of attribution obligations, distribution obligations, copyleft obligations, and intellectual property encumbrances. The use of any Open Source Software is subject to the terms and conditions of this Agreement as well as the terms and conditions of the corresponding license of each Open Source Software package. If there is a conflict between the terms and conditions of this Agreement and the terms and conditions of the Open Source Software license, the applicable Open Source Software license will take precedence. Copies of the licenses for the included Open Source Software, if any, as well as their attributions, acknowledgements, and software information details, are provided in the electronic copy of this Agreement, which is available in the Legal Notices or README file associated with the Product. Zebra is required to reproduce the software licenses, acknowledgments and copyright notices as provided by the authors and owners, thus, all such information is provided in its native language form, without modification or translation. Depending on the license terms of the specific Open Source Software, source code may not be provided. Please reference and review the entire Open Source Software information to identify which Open Source Software packages have source code provided or available. For instructions on how to obtain a copy of any source code made publicly available by Zebra related to Open Source Software distributed by Zebra, you may send your request (including the Zebra Product name and version, along with the Open Source Software specifics) in writing to: Zebra Technologies Corporation, Open Source Software Director, Legal Department, 3 Overlook Point, Lincolnshire, IL 60069 USA. 2015 ZIH Corp and/or its affiliates. All rights reserved. Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. CHAPTER 1 MPACT BLUETOOTH SMART BEACON OVERVIEW The MPact Platform employs Bluetooth Smart beacons deployable in various modes including Battery Save, iBeacon and MPact to unify Wi-Fi and Bluetooth Smart Technology to capture more analytics, accuracy and insight into consumers purchasing preferences. Use Bluetooth Smart beacons to learn which aisles and products customers prefer, their shopping history, and what influences their buying decisions. Beacon placements can be adjusted within a deployment floor plan, and depending on the mode selected, their battery life can be tracked over time. Administrators can cursor over a beacon on a sites floor plan to assess the beacons remaining battery life. This guide includes the following sections:

Beacon Hardware Specifications and Installation

RB Beacon Part Number: MPACT-T1B20-000-WR

RB Beacon Part Number: MPACT-T1B10-000-WR

2AA Beacon Part Number: MPACT-MB2000-01-WR

USB Beacon Part Number: MPACT-MB3000-01-WR

Beacon Battery Replacement

Replacing RB Battery: MPACT-T1B20-000-WR and MPACT-T1B10-000-WR

Replacing 2AA Battery: MPACT-MB2000-01-WR 1 - 2 MPact Location & Analytics Hardware Installation Guide CHAPTER 2 BEACON HARDWARE SPECIFICATIONS AND INSTALLATION The following setup processes must be complete as a prerequisite to installing beacon hardware:

MPact Server Installation and Setup - see the MPact Location & Analytics Deployment Guide

MPact Toolbox and Beacon Installation - see the MPact Location & Analytics Deployment Guide Lozier Shelves Beacon brackets for the MPACT-T1B20-000-WR and MPACT-T1B10-000-WR can be used with the following Lozier products:

TL Shelf

DL Shelf

HL Shelf

Standard Base Deck 2.1 RB Beacon Part Number: MPACT-T1B20-000-WR As a prerequisite, the following hardware items are required to mount the tie-wrap style beacon housing to a pole or similar structure:

Beacon (tie-wrap style housing), part number - MPACT-T1B20-000-WR. (When ordering, use the following part number:

MPAC-T1B20-250-WR (Box of 25)

Plastic tie wraps for attaching each beacon housing to the shelf 2.1.1 Installing the Tie-Wrap Style Beacon Tie-wrap beacon housings are designed to attach to vertical or horizontal poles or similar mounting surfaces. In Figure 2-1 below, there are openings located on the back of the beacon housing allowing a tie wrap to be inserted through the openings and wrapped around a pole or similar structure. Notice the up arrow located on the middle of the beacon housing. This arrow indicates the optimal orientation for the beacon to function properly. Additionally, the smooth front of the beacon should face outward toward the aisle where client devices are expected to engage (dwell). 2 - 2 MPact Location & Analytics Hardware Installation Guide To activate a beacon part number - MPACT-T1B20-000-WR:

1. Activate one or more beacons by pulling the mylar strip off the beacon housing. CAUTION: After pulling off the last mylar strip for the group of deployment beacons, you have 20 seconds to associate the beacon in either offline or online mode in the Toolbox application. Figure 2-1 shows a beacon with the mylar strip attached to the left-hand side of the housing. Figure 2-1 Tie Wrap Style Beacon - Part Number - MPACT-T1B20-000-WR NOTE: When installing numerous beacons, group beacons by category configurations and activate the beacons prior to scanning the barcodes and associating them with positions in the Toolbox. 2. From MPact Toolbox, select a site floor plan and an unassigned position for the beacon. Refer to the MPact Location &

Analytics Deployment Guide for information on how to install and deploy the beacon from the Toolbox. To mount the tie wrap beacon to a pole or similar structure:

1. Mount the beacon to a pole or similar structure using the plastic tie wrap. Tie can be placed vertically or horizontally but the arrow should still point up. 2.2 RB Beacon Part Number: MPACT-T1B10-000-WR As a prerequisite, the following hardware items are required to mount beacon brackets to a Lozier style shelf:

Lozier Shelves

Beacon: Part number - MPACT-T1B10-000-WR

When ordering, use the following part number: MPACT-T1B10-250-WR (Box of 25)

Bracket mount, one of the following:

MPACT Metal Lozier Bracket: Part number MPACT-A1O10-004-WR

MPACT Plastic Lozier Bracket: Part number MPACT-A1O10-001-WR

Phillips head screw driver for mounting the bracket (metal brackets only) to the Lozier shelf Beacon Hardware Specifications and Installation 2 - 3 2.2.1 Installing the Universal Style Beacon Figure 2-2 shows a universal style beacon. While there is no up arrow on this beacons housing, the beacon should be oriented similar to the tie wrap style of beacon housing, see RB Beacon Part Number: MPACT-T1B20-000-WR. Notice the up arrow located on the middle of the beacon housing. This arrow indicates the optimal orientation for the beacon to function properly. Additionally, the smooth front of the beacon should face outward toward the aisle where client devices are expected to engage (dwell). To activate a beacon part number - MPACT-T1B10-000-WR:

1. Activate one or more beacons by pulling the mylar strip off the beacon housing. CAUTION: After pulling off the last mylar strip for the group of deployment beacons, you have 20 seconds to associate the beacon in either offline or online mode in the Toolbox application. Figure 2-2 shows a beacon with the mylar strip attached to the left-hand side of the housing. Figure 2-2 Universal Style Beacon - Part Number - MPACT-T1B10-000-WR NOTE: When installing numerous beacons, group beacons by category configurations and activate the beacons prior to scanning the barcodes and associating them with positions in the Toolbox. 2. From MPact Toolbox, select a site floor plan and an unassigned position for the beacon. Refer to the MPact Location &

Analytics Deployment Guide for information on how to install and deploy the beacon from the Toolbox. To mount the universal style beacon to Lozier Shelves:

1. Mount the universal beacon shelf-bracket on the shelf:

Metal brackets: Fit in place and tighten onto the shelving unit using a phillips-head screw driver.

Plastic brackets: Fit in place and snap onto the shelving unit. 2. Fit the beacons universal style housing into the bracket (mylar tap pointing up) and turn the beacon housing clockwise 90 degrees. 2 - 4 MPact Location & Analytics Hardware Installation Guide The barcode label should face up toward the ceiling and the smooth front of the beacon should face out toward the aisle where the mobile client is expected to engage. There are two styles of bracket mounts from which to choose, either metal or plastic for Beacon: Part number - MPACT-

T1B10-000-WR. Figure 2-3 Universal Style Metal Bracket - Part Number MPACT-A1O10-004-WR Figure 2-4 Universal Style Plastic Bracket with Beacon- Bracket Part Number MPACT-A1O10-001-WR 2.3 2AA Beacon Part Number: MPACT-MB2000-01-WR As a prerequisite, the following hardware items are required to mount a beacon to a wall.

Lozier Shelves

Beacon: Part number - MPACT-MB2000-01-WR

When ordering, use the following part number: MPACT-MB2000-01-WR (Box of 25) Beacon Hardware Specifications and Installation 2 - 5

Bracket mount kit see Figure 2-6 (included with part number MPACT-MB2000-01-WR):

Metal bracket

Two 1inch Phillips head tap screw, and two 1inch plastic wall inserts

Phillips head screw driver for mounting the bracket (metal brackets only) to a wall 2.3.1 Installing the Indoor Style Beacon To activate a beacon part number - MPACT-MB2000-01-WR:

1. Activate one or more beacons by pulling the mylar strip out from inside the beacon housing. CAUTION: After pulling off the last mylar strip for the group of deployment beacons, you have 20 seconds to associate the beacon in either offline or online mode in the Toolbox application. Figure 2-5 shows the back of a Indoor style beacon. Figure 2-5 Indoor Style Beacon - MPACT-MB3000-01-WR NOTE: When installing numerous beacons, group beacons by category configurations and activate the beacons prior to scanning the barcodes and associating them with positions in the Toolbox. 2. From MPact Toolbox, select a site floor plan and an unassigned position for the beacon. Refer to the MPact Location &

Analytics Deployment Guide for information on how to install and deploy the beacon from the Toolbox.To mount the universal style beacon to a wall:

1. From MPact Toolbox, select a site floor plan and an unassigned position for the beacon. 2. Mount the Indoor Metal beacon wall bracket on the wall with the provided screws and plastic wall inserts:

Bracket mount kit:

2 - 6 MPact Location & Analytics Hardware Installation Guide There is one styles of bracket mount included with the Indoor Style Beacon: Part number - MPACT-MB2000-01-WR. Figure 2-6 Metal Beacon Wall Mount Bracket: MPACT-MB2000-01-WR 3. Fit the beacons housing into the bracket. The barcode label should face up toward the ceiling and the smooth front of the beacon should face out toward the aisle where the mobile client is expected to engage. NOTE: Ensure the beacon in positioned correctly, because once the beacon is mounted on the bracket it will be difficult to remove. Mode 0-2 seconds 2+ -5 Sleep No action Broadcast Configuration Broadcast LED Behavior No action Broadcast No action Broadcast Slow flash when button flashes 300 ms on / 300ms off. Fast flash 100ms

/on & off Solid light 5+ - 10

+ 10 Move to configuration Sleep Remain in configuration Sleep Move to configuration Sleep 2.4 USB Beacon Part Number: MPACT-MB3000-01-WR A USB powered interface is required to power the USB Beacon. No additional hardware is required. 2.4.1 Installing the USB Style Beacon Figure 2-7 shows a USB style beacon. To activate a beacon part number - MPACT-MB3000-01-WR:

1. Insert the beacon into any standard USB power source. Beacon Hardware Specifications and Installation 2 - 7 Figure 2-7 USB Style Beacon - MPACT-MB3000-01-WR When installing numerous beacons, group beacons by category configurations and activate the beacons prior to scanning the barcodes and associating them with positions in the Toolbox. 2. After inserting the beacon(s) into any standard USB power source, associate the beacon in either offline or online mode in the Toolbox application. 3. From MPact Toolbox, select a site floor plan and an unassigned position for the beacon. Refer to the MPact Location &

Analytics Deployment Guide for information on how to install and deploy the beacon from the Toolbox. The barcode label should face up toward the ceiling and the smooth front of the beacon should face out toward the aisle where the mobile client is expected to engage. 2.4.2 Beacon Battery Replacement When a beacons battery life is less than 20%, the beacon should be prioritized for immediate replacement. The beacons battery is located within a battery tray in the beacons housing. This section includes procedures for replacing batteries for the following part numbers:

Replacing RB Battery: MPACT-T1B20-000-WR and MPACT-T1B10-000-WR

Replacing 2AA Battery: MPACT-MB2000-01-WR 2.4.3 Replacing RB Battery: MPACT-T1B20-000-WR and MPACT-T1B10-000-WR To replace a beacons battery in part number MPACT-T1B20-000-WR and MPACT-T1B10-000-WR:

1. Remove the beacon from the shelving unit (see information on the appropriate beacon part number). 2. With the bottom of the beacon facing up, gently lift each corner of the beacons battery tray. Figure 2-8 shows the beacon battery housing for part number MPACT-T1B20-000-WR and MPACT-T1B10-000-WR and MPACT-T1B10-000-WR. In this example, the battery tray is on the right and the corners of the battery tray are marked in red. When gently lifting each tray corner, slightly push the each corner out to dislodge corners of the tray. Figure 2-8 Beacon Battery Housing Example: MPACT-T1B20-000-WR and MPACT-T1B20-000-WR and MPACT-T1B10-000-WR 3. With both tray corners dislodged, gently slide the battery tray open, being careful not to drop the tray. Figure 2-9 shows an open battery housing. In this example, the battery tray is a separate piece, along with the battery, on the right-hand side. 2 - 8 MPact Location & Analytics Hardware Installation Guide Figure 2-9 Battery Tray: MPACT-T1B20-000-WR and MPACT-T1B20-000-WR and MPACT-T1B10-000-WR 4. Remove the old battery and dispose of properly and replace it with a new battery (Panasonic CR2450). NOTE: Pay attention to the position of the + on the battery. Installing the battery backwards may damage the Beacon 5. Close the tray, ensuring the latch is secure. 2.4.4 Replacing 2AA Battery: MPACT-MB2000-01-WR To replace a beacons battery in part number MPACT-MB2000-01-WR:

1. Remove the beacon from the shelving unit (see information on the appropriate beacon part number). 2. With the bottom of the beacon facing up, use your finger nail to gently lift the clip up to remove the back off the beacons battery enclosure. 3. Remove the old batteries and dispose of properly and replace it with two new 2AA batteries. NOTE: Pay attention to the polarity (+ and -) of the batteries. Installing the batteries incorrectly may damage the Beacon. Figure 2-10 shows an open battery enclosure of Indoor Style Beacon. 4. Close the battery enclosure, ensuring the clip is secure. Figure 2-10 Open Battery Enclosure: MPACT-MB2000-01-WR APPENDIX CUSTOMER SUPPORT If you have a problem with your equipment, contact Support for your region. Support and issue resolution is provided for products under warranty or that are covered by a services agreement. Contact information and Web self-service is available by visiting www.zebra.com/support. When contacting Support, please provide the following information:

MAC ID of the unit

Model number or product name

Software type and version number Support responds to calls by email or telephone within the time limits set forth in support agreements. If you purchased your product from a business partner, contact that business partner for support. Customer Support Web Site The support site, located at www.zebra.com/support provides information and online assistance including developer tools, software downloads, product manuals, support contact information and online repair requests. Manuals To see manuals, go to:www.zebra.com/support. A - 2 MPact Location & Analytics Toolbox Reference Guide MN002236A01 Revision A June 2015

Regulatory Information All Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help. This regulatory information applies to Model number MPACT-INDR1. Local language translations are available at the following website:

www.zebra.com/support Radio Transmitters (Part 15) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications to Zebra equipment, not expressly approved by Zebra, could void the users authority to operate the equipment. Radio Frequency Interference Requirements - Canada Wireless Device Country Approvals Regulatory markings, subject to certification, are applied to the device signifying the radio(s) is/are approved for use in the following countries: United States and Canada. Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at www.zebra.com/doc. This device is in compliance with the NRC for Industry Canada applicable to license-exempt radios. Use is allowed with the following two conditions: (1) the device must not produce interference, and (2) the device must accept any interference to the radio, even if the interference is likely to compromise operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Operation of the device without regulatory approval is illegal. Waste Electrical and Electronic Equipment (WEEE) Bluetooth Smart Wireless Technology This is an approved Bluetooth product. For more information or to view End Product Listing, please visit https://www.bluetooth.org/tpg/listings.cfm. English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return product, please go to: www.zebra.com/weee Franais: Clients de l'Union Europenne: Tous les produits en fin de cycle de vie doivent tre retourns Zebra pour recyclage. Pour de plus amples informations sur le retour de produits, consultez :

www.zebra.com/weee. Warnings for use of Wireless Devices Please observe all warning notices with regard to the usage of wireless devices. Potentially Hazardous Atmospheres Vehicles Use You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals or particles (such as grain, dust, or metal powders) and any other area where you would normally be advised to turn off your vehicle engine. Potentially Hazardous Atmospheres Fixed Installations You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals or particles (such as grain, dust, or metal powders). Safety in Aircraft Switch off your wireless device whenever you are instructed to do so by airport or airline staff. If your device offers a flight mode or similar feature, consult airline staff as to its use in flight. Safety Information RF Exposure Guidelines Reducing RF Exposure - Use Proper Only operate the device in accordance with the instructions supplied. International The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. For information on International human exposure to electromagnet fields refer to the Motorola Declaration of Conformity (DoC) at www.zebra.com/doc. For further information on the safety of RF energy from wireless devices, see www.zebra.com/support. This is located under Wireless Communications and Health. Radio Frequency Interference Requirements- FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Product Introduction Guide Part Numbers: MPACT-MB2000-001-WR Customer Support Web Site If you have a problem with your equipment, contact Support for your region. Support and issue resolution is provided for products under warranty or that are covered by a service agreement. For information and online assistance including developer tools, software downloads, product manuals, support contact information and online repair requests. Contact information and web self-service is available by visiting www.zebra.com/support. When contacting Support, please provide the following information:

MAC ID of the product shown on the side of the product next to the barcode Model number or product name shown on the label on the back of the product. Tag Mounts and Installation For mounting and installation information see the guide, MPact Location and Analytics Deployment Guide on the web site: www.zebra.com/support. Batteries Important: Replace batteries with 2xAA alkaline batteries only. Dispose of batteries in accordance with local governmental regulations. For information on how to remove and reinsert a battery, see the guide, MPact Location & Analytics Hardware Installation Guide on the web site, www.zebra.com/support. Other Licenses This logo indicates that this product is licensed to operate according to Apples iBeacon specifications. MN001981A01 Revision A June 2015

Label locatesinsidethebatterycompartment.Theuserswillseethelabel astheyopenthebackcovertoinstalllthebattery. LabelLocation

ZEBRA TECHNOLOGIES CORPORATION HOTSVILLE N.Y. 11742 MODEL: MPACT-INDR1 CAN ICES-3 (B) /NMB-3 (B) FCC ID: UZ7MPACTINDR1 E252240 IC: 109AN-MPACTINDR1 Cc us KC fy yi LISTED LE:

Regulatory Engineering June 30, 2015 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To the Commission, Confidentiality Request regarding application for certification of FCC ID: UZ7MPACTINDR1 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request Permanent Confidential treatment of information accompanying this application as outlined below:

Tune up Procedure Operational Description Block Diagram Schematics Parts List The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Pursuant to sections 0.457 and 0.459 of CFR 47 and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 180 days:

Test Setup Photos User Manual External Photos Internal Photos The application contains technical information, which the applicant deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Zebra Technologies Corporation 1 Z e b r a P l a z a , | H o l t s v i l l e , N Y 1 1 7 4 2 | 1 . 6 3 1 . 7 3 8 . 2 4 0 0 p h o n e | 1 . 6 3 1 . 6 2 7 . 7 1 7 9 f a x | www. z e b r a . c o m Regulatory Engineering Power of Attorney Please be notified that we, have designated Jones Tsai in Sporton International Inc. as the person being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Jones Tsai in Sporton International Inc. on the matters of relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002 (b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 835(a). This authorization is limited to the product of as following:

FCC ID: UZ7MPACTINDR1 If you have any acknowledgement and response, please send it to Sporton International Inc. directly. Respectfully, Mark S. Luksich DMTS, Regulatory Engineering 631-738-5134 Mark.Luksich@Zebra.com Zebra Technologies Corporation 1 Z e b r a P l a z a , | H o l t s v i l l e , N Y 1 1 7 4 2 | 1 . 6 3 1 . 7 3 8 . 2 4 0 0 p h o n e | 1 . 6 3 1 . 6 2 7 . 7 1 7 9 f a x | www. z e b r a . c o m

Regulatory Engineering July 17, 2015 FCC Laboratory 7435 Oakland Mills Rd. Columbia, MD 21046 SUBJECT: FCC Application for FCC ID: UZ7MPACTINDR1 To the Commission, We hereby attest to the fact that we will apply the Declaration of Conformity procedure to the class B computer peripheral portion of this composite filing. Respectfully, Mark S. Luksich DMTS, Regulatory Engineering 631-738-5134 Mark.Luksich@Zebra.com Zebra Technologies Corporation 1 Z e b r a P l a z a , | H o l t s v i l l e , N Y 1 1 7 4 2 | 1 . 6 3 1 . 7 3 8 . 2 4 0 0 p h o n e | 1 . 6 3 1 . 6 2 7 . 7 1 7 9 f a x | www. z e b r a . c o m