1. Regulatory Information This device is approved under Zebra Technologies Corporation. This guide applies to Model Number: CDR2G All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold and will be labeled as required. Local language translations are available at the following website: www.zebra.com/support. Any changes or modifications to Zebra equipment not expressly approved by Zebra could void the users authority to operate the equipment. Zebra devices are professionally installed the Radio Frequency Output Power will not exceed the maximum allowable limit for the country of operation. Antennas: Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could cause damage and may violate regulations. This device is only to be used with a Zebra Wireless Switch. For use only with Zebra approved and UL Listed mobile computers, Zebra approved, and UL Listed/Recognized battery packs. 2. Wireless Device Country Approvals Note: This section is only applicable to WW/WR/EU configurations. Regulatory markings subject to certification are applied to the device signifying the radio(s) is/are approved for use in the following countries and continents: United States, Canada, Japan, China, South Korea, Australia, and Europe. Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at:
http://www.zebra.com/doc. Note: Europe includes Austria, Belgium, Bulgaria, Croatia, Czech Republic, Cyprus, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland, and the United Kingdom. Caution: Operation of the device without regulatory approval is illegal. Country Selection Select only the country in which the device will be used. Any other selection will make the operation of this device illegal. Country Roaming This device incorporates the International Roaming feature (IEEE802.11d), which will ensure the product operates on the correct channels for the particular country of use. Frequency of Operation IC 2.4 GHz Only:
The available channels for 802.11 b/g operation in the US are Channels 1 to 11. The range of channels is limited by firmware. Warnings for Use of Wireless Devices Zebra Technologies Corporation Zebra Confidential Restricted Regulatory Guide (RG) Rev. A warning notices with regard to the usage of wireless devices. Caution: Please observe all Potentially Hazardous Atmospheres Fixed Installations You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals or particles such as grain, dust, or metal powders. Safety in Aircraft Switch off your wireless device whenever you are instructed to do so by airport or airline staff. If your device offers a flight mode or similar feature, consult airline staff as to its use in flight. Safety in Hospitals Wireless devices transmit radio frequency energy and may affect medical electrical equipement. Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics, or healthcare facilitlies. These requests are designed to prevent possible interference with sensitive medical equipement. Wireless devices transmit radio frequency energy and may affect medical electrical equipment. When installed adjacent to other equipment, it is advised to verify that the adjacent equipment is not adversely affected. Pacemakers Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with independent research and recommendations by Wireless Technology Research. Persons with Pacemakers:
Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON. Should not carry the device in a breast pocket. Should use the ear furthest from the pacemaker to minimise the potential for interference. If you have any reason to suspect that interference is taking place, turn OFF your device. Other Medical Devices Please consult your physician or the manufacturer of the medical device to determine if the operation of your wireless product may interfere with the medical device. RF Exposure Guidelines Safety Information Reducing RF Exposure Use Properly Only operate the device in accordance with the instructions supplied. International Zebra Technologies Corporation Zebra Confidential Restricted Page 2 of 9
. Regulatory Guide (RG) Rev. A The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. For information on International human exposure to electromagnet fields, refer to the Zebra Declaration of Conformity (DoC) at http://www.zebra.com/doc For further information on the safety of RF energy from wireless devices, see http://responsibility.zebra.com/index.php/downloads/, which is located under Wireless Communications and Health. US and Canada o Co-located statement To comply with FCC RF exposure compliance requirement, the antenna used for this transmitter must not be co-located or operating in conjunction with any other transmitter/antenna except those already approved in this filling. To satisfy US and Canadian RF exposure requirements, a transmitting device must operate with a minimum separation distance of 40 cm or more from a persons body. Pour satisfaire aux exigences Amricaines et Canadiennes d'exposition aux radio frquences, un dispositif de transmission doit fonctionner avec une distance de sparation minimale de 40 cm ou plus de corps d'une personne. Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 40 cm between the radiator and your body. NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles) Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 40 cm de distance entre la source de rayonnement et votre corps. o Remote and Standalone Antenna Configurations To comply with FCC RF exposure requirements, antennas that are mounted externally at remote locations or operating near users at stand-alone desktop of similar configurations must operate with a minimum separation distance of 40 cm from all persons. To comply with FCC Antenna requirements, the Antenna must be adjust such that the RF emission lobes are below 30 degrees elevation. Zebra Technologies Corporation Zebra Confidential Restricted Page 3 of 9 Regulatory Guide (RG) Rev. A 3. Radio Frequency Interference Requirements- FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Increase the separation between the equipment and receiver. Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Radio Transmitters (Part 15) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 40 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID: UZ7CDR2G ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Zebra Technologies Corporation Zebra Confidential Restricted Page 4 of 9 Regulatory Guide (RG) Rev. A 4. Radio Frequency Interference Requirements- Canada CAN ICES-3 (B)/NMB-3(B) Radio Transmitters This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio lectrique subi mme si le brouillage est susceptible d'en compromettre le fonctionnement. Label Marking: The Term IC: before the radio certification only signifies that Industry Canada technical specifications were met. In accordance with the regulations of Industry Canada, this radio transmitter can operate with an antenna of a type and a maximum gain (or lower) approved for the transmitter by Industry Canada. With the aim of reducing the risk of radio interference to other users, the chosen antenna type and it gain should be selected so that the equivalent isotropically radiated power (e.i.r.p.) does not exceed the intensity necessary for the establishment of a satisfactory connection. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radio lectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. This radio transmitter (CDR2G) has been approved by Industry Canada to operate with the antenna types listed below and having a maximum gain allowable and the impedance required for each type of antenna. The antenna types not included in this list, or whose gain is higher than the maximum gain indicates, are strictly prohibited for the operation of the transmitter. Zebra Technologies Corporation Zebra Confidential Restricted Page 5 of 9 Regulatory Guide (RG) Rev. A The antenna list and types are included in the following table:
2.4 GHZ Gain
(dBi) Antenna Type Impedance
(Ohms) Part Number ML-2452-HPAG4A6-01 Dipole 4 ML-2452-APAG2A1-01 Dipole ML-2452-HPA6-01 Dipole 2.7 5.3 ML-2452-APA2-01 Dipole 3.17 ML-2452-PNA5-01R Panel 5.5 ML-2452-SEC5M4-N36 Polarized Panel 6.92 ML-2452-PTA4M4-036 Patch 5 ML-2499-HPA6H-01 Polarized Dipole 5.4 ML-2452-HPAG4A6-01 Polarized Dipole 4 50 50 50 50 50 50 50 50 50 CEDAR-INT-ANT Mono pole 5.2 N/A Le prsent metteur radio (CDR2G) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 40 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains IC: 109AN-CDR2G ". The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online. Zebra Technologies Corporation Zebra Confidential Restricted Page 6 of 9 Regulatory Guide (RG) Rev. A 5. CE Marking and European Economic Area (EEA) WARNING: This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
:
The use of 2.4GHz RLANs, for use through the EEA, have the following restrictions:
Maximum radiated transmit power of 100mW EIRP in the frequency range 2.400 -2.4835 GHz. Statement of Compliance Zebra hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC and 2011/65/EU. A Declaration of Conformity may be obtained from http://www.zebra.com/doc. 6. Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return product, please go to: www.zebra.com/weee. Franais: Clients de l'Union Europenne: Tous les produits en fin de cycle de vie doivent tre retourns Zebra pour recyclage. Pour de plus amples informations sur le retour de produits, consultez :
www.zebra.com/weee. Espaol: Para clientes en la Unin Europea: todos los productos debern entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si desea ms informacin sobre cmo devolver un producto, visite:
www.zebra.com/weee.
: :
Zebra . , :
www.zebra.com/weee. Deutsch: Fr Kunden innerhalb der EU: Alle Produkte mssen am Ende ihrer Lebensdauer zum Recycling an Zebra zurckgesandt werden. Informationen zur Rcksendung von Produkten finden Sie unter www.zebra.com/weee. Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni sulle modalit di restituzione, visitare il seguente sito Web: www.zebra.com/weee. Portugus: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos Zebra para reciclagem. Para obter informaes sobre como devolver o produto, visite: www.zebra.com/weee. Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg www.zebra.com/weee voor meer informatie over het terugzenden van producten. Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji naley zwrci do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktw znajduj si na stronie internetowej www.zebra.com/weee. etina: Pro zkaznky z EU: Vechny produkty je nutn po skonen jejich ivotnosti vrtit spolenosti Zebra k recyklaci. Informace o zpsobu vrcen produktu najdete na webov strnce: www.zebra.com/weee. Eesti: EL klientidele: kik tooted tuleb nende eluea lppedes tagastada taaskasutamise eesmrgil Zebra'ile. Lisainformatsiooni saamiseks toote tagastamise kohta klastage palun aadressi: www.zebra.com/weee. Magyar: Az EU-ban vsrlknak: Minden tnkrement termket a Zebra vllalathoz kell eljuttatni jrahasznosts cljbl. A termk visszajuttatsnak mdjval kapcsolatos tudnivalkrt ltogasson el a www.zebra.com/weee weboldalra. Svenska: Fr kunder inom EU: Alla produkter som uppntt sin livslngd mste returneras till Zebra fr tervinning. Information om hur du returnerar produkten finns p www.zebra.com/weee. Zebra Technologies Corporation Zebra Confidential Restricted Page 7 of 9 Regulatory Guide (RG) Rev. A Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrtettvksi Zebra-yhtin, kun tuotetta ei en kytet. Listietoja tuotteen palauttamisesta on osoitteessa www.zebra.com/weee. Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, nr de er udtjent. Ls oplysningerne om returnering af produkter p: www.zebra.com/weee.
: ..: , , Zebra .
, www.zebra.com/weee . Malti: Gal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aar tal-ajja ta' l-uu taghom, iridu jiu rritornati gand Zebra gar-riikla. Gal aktar tagrif dwar kif gandek tirritorna l-prodott, jekk jogbok ur:
www.zebra.com/weee. Romnesc: Pentru clienii din UE: Toate produsele, la sfritul duratei lor de funcionare, trebuie returnate la Zebra pentru reciclare. Pentru informaii despre returnarea produsului, accesai: www.zebra.com/weee. Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku ivljenjske dobe vrniti podjetju Zebra za reciklao. Za informacije o vrailu izdelka obiite: www.zebra.com/weee. Slovenina: Pre zkaznkov z krajn EU: Vetky vrobky musia by po uplynut doby ich ivotnosti vrten spolonosti Zebra na recyklciu. Bliie informcie o vrten vrobkov njdete na: www.zebra.com/weee. Lietuvi: ES vartotojams: visi gaminiai, pasibaigus j eksploatacijos laikui, turi bti grinti utilizuoti kompanij Zebra. Daugiau informacijos, kaip grinti gamin, rasite: www.zebra.com/weee. Latvieu: ES klientiem: visi produkti pc to kalpoanas ma beigm ir jnogd atpaka Zebra otrreizjai prstrdei. Lai iegtu informciju par produktu nogdanu Zebra, ldzu, skatiet: www.zebra.com/weee. Trke: AB Mterileri iin: Kullanm sresi dolan tm rnler geri dntrme iin Zebra'ya iade edilmelidir. rnlerin nasl iade edilecei hakknda bilgi iin ltfen u adresi ziyaret edin: www.zebra.com/weee. Korea Warning Statement for Class B ITE B
(B)
( )
,
. South Korea For a radio equipment using 2400~2483.5MHz or 5725~5825MHz, the following two expression should be displayed;
Zebra Technologies Corporation Zebra Confidential Restricted Page 8 of 9 Regulatory Guide (RG) Rev. A Taiwan
()
/
MPE1mW/cm 40 cm Zebra Technologies Corporation Zebra Confidential Restricted Page 9 of 9