Mounting holes for screws Mounting holes for cable ties Interface port LED indicator Page button Pairing barcode 1 2 3 4 5 6 Mounting the Adapter Place the adapter on a tabletop or mount it on a vertical surface. Select a mounting location where the pairing barcode is visible. Horizontal Surface Mounting Place the adapter on a horizontal surface. The rubber feet provide traction and prevent surface damage. Vertical Surface Mounting The adapter may be mounted onto vertical surfaces using either screws or cable ties. Mounting the Adapter With Screws Mount the adapter using screws to hold it in place. Use four M5 screws at least 13 mm long. 1. Place the Bluetooth Adapter on the desired location. 2. Mark the surface through the four mounting holes to determine the location of the screw holes. 3. Pre-drill the holes to accommodate four M5 screws. BT-RS5X6-DNGL Bluetooth Adapter Quick Reference Guide MN-004841-01EN-P Rev A Zebra Technologies | 3 Overlook Point | Lincolnshire, IL 60069 USA www.zebra.com | ip.zebra.com ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. 2023 Zebra Technologies Corporation and/or its affiliates. All rights reserved. Getting Started The BT-RS5X6-DNGL Bluetooth Adapter provides Bluetooth capability to a host computer. Place it on a horizontal surface or mount it vertically. The Bluetooth Adapter is compatible with RS5100 devices using CAAEXS00-001-R07 or later and all RS6100 devices. Refer to the Adapter's Product Reference Guide (p/n MN-004832-01EN) for adapter conguration information. Features 1 2 3 4 5 6 Mounting the Adapter with Cable Ties Mount the adapter using cable ties to hold it in place. Use two cable ties a maximum 8 mm wide and 3 mm thick. NOTE: Mount the adapter no more than 2 m (6 ft 5in.) above the oor. 1. Place the Bluetooth adapter in the desired location. 2. Thread a cable tie through the top two mounting holes and wrap it around the pole. Tighten the cable tie. 1. Connect the latching end of the cable to the Bluetooth adapter port. Press the cable rmly until you hear a click to ensure it is fully inserted into the port. 2. Connect the USB end of the cable to the host computer. Pairing Scan the adapter's pairing barcode to pair it with a Zebra scanner. 3. Trim excess cable tie length. 4. Repeat the process for the bottom mounting holes. Connecting the Adapter Connect the Bluetooth Adapter to the host computer to provide a Bluetooth connection. Use cable CBA-U46-S07ZAR. Modes of Operation Select a mode of operation:
Point-to-Point: Scan the pairing barcode on the Bluetooth Adapter to pair it with your Multipoint-to-Point: Pair up to seven Zebra scanners with one adapter. To use this feature, scan the multipoint barcode when the scanner is connected to the adapter. Zebra scanner. NOTE: Refer to the scanner's Product Reference Guide for more information about Zebra scanner conguration. Point-to-Point Mode 4. Attach the adapter securely to the surface. Multipoint-to-Point Mode Using the Page Button Activate the page button to help nd paired scanners. The page button is a touch-sensitive sensor. 1. for approximately one second. Press Page The adapter LED indicator turns blue and all connected scanners emit an alert. Based on scanner capability and conguration, the alert may be visual (ashing LED), auditory (beeping), or haptic (vibration). 2. Repeat as needed until the missing scanners are located. NOTE: Scanners out of radio range will not alert when paged. Troubleshooting If the adapter does not work after following the previous procedures:
Check the system power. Check for loose cable connections. Check that the host computer settings are correct and that the adapter is Regulatory Information This device is approved under Zebra Technologies Corporation. This guide applies to the following model number: BT-RS5X6-DNGL connected to the appropriate port. All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold and will be labeled as required. Local language translation / (BG) / (CZ) P#eklad do mstnho jazyka / (DE) bersetzung in die Landessprache / (EL) # ## ## /(ES) Traduccin de idiomas locales / (ET) Kohaliku keele tlge / (FI) Paikallinen knns / (FR) Traduction en langue locale / (HR) Prijevod na lokalni jezik / (HU) Helyi nyelv# fordts / (IT) Traduzione in lingua locale / (JA) / (KR) / (LT) Vietin#s kalbos vertimas / (LV) Tulkojums vietj valod / (NL) Vertaling in lokale taal / (PL) T#umaczenie na j#zyk lokalny / (PT) Traduo do idioma local /(RO) Traducere n limba local / (RU)
/ (SK) Preklad do miestneho jazyka / (SL) Prevajanje v lokalni jezik / (SR) # /(SV) versttning av lokalt sprk / (TR) Yerel dil evirisi / (ZH-CN) / (ZH-TW) zebra.com/support Any changes or modications to Zebra equipment not expressly approved by Zebra could void the user's authority to operate the equipment. Declared maximum operating temperature: 50C For use only with Zebra approved and UL Listed mobile devices, Zebra approved. Bluetooth Wireless Technology This is an approved Bluetooth product. For more information on the Bluetooth SIG listing, please visit www.bluetooth.com. Regulatory Markings Regulatory markings subject to certication are applied to the device. Refer to the Declaration of Conformity (DoC) for details of other country markings. The DOC is available at: zebra.com/doc. Health and Safety Recommendations This section provides important health and safety recommendations. Safety in Hospitals and Aircraft Wireless devices transmit radio frequency energy that may aect medical electrical equipment and aircraft operation. Wireless devices should be switched o wherever you are requested to do so in hospitals, clinics, healthcare facilities, or by airline sta. These requests are designed to prevent possible interference with sensitive equipment. RF Exposure Guidelines CAUTION: Important Safety Information Reducing RF Exposure Use Properly Only operate the device in accordance with the instructions supplied. The device complies with internationally recognized standards covering human exposure to electromagnetic elds. For information on international human exposure to electromagnetic elds, refer to the Zebra Declaration of Conformity (DoC) at www.zebra.com/doc. Use only Zebra tested and approved headset, belt-clips, holsters, and similar accessories to ensure RF exposure compliance. If applicable, follow the instructions for use as detailed in the accessory guide. The use of third-party belt clips, holsters, and similar accessories may not comply with RF exposure compliance requirements and should be avoided. For further information on the safety of RF energy from wireless devices, refer to RF exposure and assessment standards section at www.zebra.com/responsibility. Marking and European Economic Area
(EEA) Statement of Compliance Zebra hereby declares that this radio equipment is in compliance with Directives 2014/53/EU and 2011/65/EU. Any radio operation limitations within EEA countries are identied in Appendix A of EU Declaration of Conformity. The full text of the EU Declaration of Conformities is available at: zebra.com/doc. EU Importer : Zebra Technologies B.V Address: Mercurius 12, 8448 GX Heerenveen, Netherlands Environmental Compliance For compliance declarations, recycling information, and materials used for products and packaging, please visit www.zebra.com/environment. Waste Electrical and Electronic Equipment (WEEE) For EU and UK Customers: For products at the end of their life, please refer to recycling/
disposal advice at: www.zebra.com/weee. United States and Canada Regulatory Radio Frequency Interference Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
receiver is connected. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the Consult the dealer or an experienced radio/TV technician for help. Radio Frequency Interference Requirements Canada Innovation, Science and Economic Development Canada ICES-003 Compliance Label: CAN ICES-003 (B)/NMB-003(B) This device complies with Innovation, Science and Economic Development Canadas licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio lectrique subi mme si le brouillage est susceptible d'en compromettre le fonctionnement. RF Exposure Requirements - FCC and ISED The FCC has granted Equipment Authorization for this device with all reported SAR levels evaluated in compliance with the FCC RF emission guidelines. SAR information on this device is on le with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid. This equipment complies with RF Exposure limits established for an uncontrolled environment (General Population). This equipment should be installed and operated in such a way that a separation distance of greater than 20 (or 20) centimeters is maintained between the transmitter's radiating structure(s) and the body of the user or nearby persons. Cet quipement est conforme aux limites d'exposition aux RF tablies pour un environnement non contrl (population gnrale). Cet quipement doit tre install et utilis de manire maintenir une distance de sparation suprieure 20 or 20 centimtres entre la (les) structure (s) rayonnante (s) de l'metteur et le corps de l'utilisateur ou des personnes proximit. Co-located Statement To comply with FCC RF exposure compliance requirement, the antenna used for this transmitter must not be co-located (within 20 cm) or operating in conjunction with any other transmitter/antenna except those already approved in this lling.
(Taiwan)
/ 9 13 BT-RS5X6-DNGL Restricted substances and its chemical symbols
(Pb) (Hg) (Cd) (Cr+6) (PBB) (PBDE) O O O X O O Unit 1. 0.1 wt % 0.01 wt %
2. O 3. O O O O O O O O O O O O Note 1: Exceeding 0.1 wt% and exceeding 0.01 wt% indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition. Note 2: O indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence. Note 3: The indicates that the restricted substance corresponds to the exemption. Trkiye Bu cihaz Trke karakterlerin tamam#n# ihtiva eden ETSI TS 123.038 V8.0.0 (veya sonraki srmnkodu) ve ETSI TS 123.040 V8.1.0 (veya sonraki srmn kodu) teknik zelliklerine uygundur. TRK WEEE Uyumluluk Beyan#
EEE Ynetmeli#ine Uygundur. United Kingdom Statement of Compliance Zebra hereby declares that this radio equipment is in compliance with the Radio Equipment Regulations 2017 and the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. Any radio operation limitations within UK are identied in Appendix A of UK Declaration of Conformity. The full text of the UK Declaration of Conformities is available at: zebra.com/doc. UK Importer: Zebra Technologies Europe Limited Address:
Dukes Meadow, Millboard Rd, Bourne End, Buckinghamshire, SL8 5XF Warranty For the complete Zebra hardware product warranty statement, go to: zebra.com/warranty . Service Information Before you use the unit, it must be congured to operate in your facility's network and run your applications. If you have a problem running your unit or using your equipment, contact your facility's Technical or System Support. If there is a problem with the equipment, they will contact Zebra support at zebra.com/support. For the latest version of the guide go to: zebra.com/support. Software Support Zebra wants to ensure that customers have the latest entitled software at the time of device purchase in order to keep the device operating at peak performance levels. To conrm that your Zebra device has the latest entitled software available at the time of purchase, go to zebra.com/support. Check for the latest software from Support > Products, or search for the device and select Support > Software Downloads. If your device does not have the latest entitled software as of your device purchase date, e-
mail Zebra at entitlementservices@zebra.com and ensure you include the following essential device information:
Model number Serial number Proof of purchase Title of the software download you are requesting. If it is determined by Zebra that your device is entitled to the latest version of software, as of the date you purchased your device, you will receive an e-mail containing a link directing you to a Zebra Web site to download the appropriate software. Product Support Information For information on using this product, see the User Guide at zebra.com/support. To nd quick answers to known product behaviors, access our knowledge articles at Ask your questions in our Support community at supportcommunity.zebra.com. Download product manuals, drivers, software, and view how-to videos at To request a repair for your product, go to zebra.com/repair. Patent Information To view Zebra patents, go to ip.zebra.com. supportcommunity.zebra.com/s/knowledge-base. zebra.com/support.