HS3100 OTH BTN Rugged Bluetooth Headset Features Over-the-Head (OTH) T-Bar Flexible Microphone Boom Adjustable Headband Not Connected Blue Connected Blue flash every two seconds Battery Status Low Battery Shutdown Red and flashes three times Low Battery Warning Red flashes twice every two seconds until battery shutdown Battery Charging (USB) Red Single Ear Piece Ear Piece Assembly Charge the Battery Battery Buttons/
LED Microphone with Windscreen Disassembly Knob Tap to Pair (NFC Pairing) Scan to Pair (Bar Code Pairing) Manual Pairing (Provisioning the HS MAC Address) Position the Boom Left Side Boom Placement Right Side Boom Placement Do not rotate the boom beyond the stop point.
* Applies to OTH model. The BTN model has only left side boom placement. Adjust the OTH Headband Quick Start Guide Behind-the-Neck (BTN) Left Placement Single Ear Piece Flexible Microphone Boom Battery Buttons/
LED Microphone with Windscreen Disassembly Knob Insert the battery into the charger with the contacts facing forward. Insert the Battery Headband BTN with Adjustable Strap Note: This guide applies to both the OTH and BTN headband models, unless otherwise noted. Buttons/LED Insert the battery with the contacts facing outward. Power On Headset Adjust the Microphone Position the microphone icon so that it is facing your mouth. Adjust the Microphone Boom Low Backup Power Time Tone: ??
Prompt: ??
Mute Un-mute To On Tone: Two tones failing Tone: Two tones raising Tone: Four rising tones To Low Power Tone: Four descending tones Maintenance Replace T-Bar Replace Headband Place the microphone two fingers width away from the corner of your mouth, so it is slightly to one side. Mute the Microphone The headband can be squeezed for a tighter fit to the head and clicks as it is positioned into place. When adjusting the headband, Position the ear pad in the center of the ear. Position the T-Bar above the ear, half way between the top of the ear and the top of the head.
* Applies to OTH model. Adjust the BTN Headband Strap Place the microphone boom in the upright position. Adjust the Volume Volume UP/DOWN Buttons
* Applies to OTH model. Replace Headband Pad 2 1 Disassemble the headset to replace the headband. Replace Ear Pad Firmly grip and pull the ear pad and inner casing. NFC Tag Volume Main Function Button Main Function Button Loosen or tighten the velcro closure on each end to increase or decrease the length of the strap. Audio Tones and Prompts 3 4 Remove the T-Bar and then the headband pad. Align and snap the new fear pad into position. Replace Windscreen Press the Main Function button to turn the power on. The headset LED illuminates blue and flashes three times. Pair Headset with Device Buttons/
Function LED Indicator NFC Tag Power ON Power OFF Pair Main Function Button Blue and flashes three times Red and flashes three times Blue and Red alternate flash Connection Status NFC Pairing Bar Code Pairing The headset can be paired in any of the following ways:
Slide the clips forward or backward to move the strap closer or further from the headband.
* Applies to BTN model. Function Audio Tone/Prompts Start Pairing Tone: Two short beeps - low Successful Pairing Tone: Three beeps - raising Device Connected Tone: One beep Prompt: From the application Bluetooth Link Lost Tone: Two low tones followed by high tone Low Battery Tone: Two short beeps triggered every two minutes until shutdown Prompt: While connected from the application Replace the headband pad and then the T-Bar.
* Applies to OTH model. Remove the Battery Zebra reserves the right to make changes to any product to improve reliability, function, or design. Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Zebra products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Zebra products. Warranty For the complete Zebra hardware product warranty statement, go to:
http://www.zebra.com/warranty. Service Information Before you use the unit, it must be configured to operate in your facilitys network and run your applications. If you have a problem running your unit or using your equipment, contact your facilitys Technical or Systems Support. If there is a problem with the equipment, they will contact the Zebra Global Customer Support at:
http://www.zebra.com/support. For the latest version of this guide go to: http://www.zebra.com/support. Zebra Technologies Corporation, Lincolnshire, IL USA http://www.zebra.com Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. 2016 Symbol Technologies LLC, a subsidiary of Zebra Technologies Corporation. All rights reserved. MN-002762-01 Revision A July 2016 More Information For more information, refer to the HS3100 Bluetooth Headset User Guide. Parts and Accessories Health and Safety Recommendations Safety on the Road Part Number Description HS3100-OTH HS3100-BTN-L HS3100 Rugged Bluetooth Headset (Over-the-Head Headband) HS3100 Rugged Bluetooth Headset (Behind-the-Neck Headband Left) SAC-HS3100-B8W8-01 HS3100 8-Slot-Battery Charger
& 8-Slot-WT6000 Charger SAC-HS3100-B8-01 HS3100 8-Slot-Battery Charger A9310272-003 HS3100 8-Slot-Battery Charger Spare Cup BTRY-HS3100-HS1-01 HS3100 Single Battery BTRY-HS3100-HS1-08 HS3100 Battery Pack of 8 KT-HSX100-OTH1-10 KT-HSX100-BTNL1-10 KT-HSX100-OTHP1-10 Over-the-Head Headband Pack of 10 Behind-the-Neck Headband Left Pack of 10 HSX100-OTH Headband Pad Pack of 10 KT-HSX100-STRP1-10 HSX100-BTN Strap Pack of 10 KT-HSX100-EPF1-20 KT-HSX100-EPL1-20 KT-HSX100-MWS1-50 CBL-HS3100-CUC1-01 HSX100 Headset Foam Ear Pad Pack of 20 HSX100 Headset Leatherette Ear Pad Pack of 20 HSX100 Headset Series Microphone Windscreen Pack of 50 USB TYPE-A 36" (0.9M) CHARGING AND COMMUNICATION CABLE KT-HSX100-TBP1-20 T-BAR WITH PAD PACK OF 20 Regulatory Information This device is approved under Zebra Technologies Corporation. This guide applies to Model Number HS3100. All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold and will be labeled as required. Local language translations are available at the following website:
www.zebra.com/support. Any changes or modifications to Zebra equipment not expressly approved by Zebra could void the user's authority to operate the equipment. Bluetooth Wireless Technology This is an approved Bluetooth product. For more information or to view the End Product Listing, please visit https://www.bluetooth.org/tpg/
listings.cfm. Do not take notes or use the device while driving. Jotting down a to do list or flipping through your address book takes attention away from your primary responsibility; driving safely. When driving a car, driving is your first responsibility - give your full attention to driving. Check the laws and regulations on the use of wireless devices in the areas where you drive. Always obey them. Warnings for Use of Wireless Devices Please observe all warning notices with regard to the usage of wireless devices. RF Exposure Guidelines Safety Information Reducing RF Exposure - Use Properly Only operate the device in accordance with the instructions supplied. International The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. For information on 'International' human exposure to electromagnet fields, refer to the Zebra Declaration of Conformity (DoC) at:
http://www.zebra.com/doc. For further information on the safety of RF energy from wireless devices, see https://www.zebra.com/us/en/about-zebra/company-information/
corporate-responsibility.html located under Corporate Responsibility. Batteries EPA (Environmental Protection Administration) requires dry battery producing or importing firms in accordance with Article 15 of the Waste Disposal Act are required to indicate the recycling marks on the batteries used in sales, giveaway, or promotion. Contact a qualified Taiwanese recycler for proper battery disposal. Battery Information CAUTION Risk of explosion if battery is replaced by an incorrect type. Dispose of batteries according to instructions. Use only Zebra approved batteries. Accessories which have battery charging capability are approved for use with the following battery models:
Part Number BTRY-HS3100-HS-01 (3.7 VDC, 210 mAh). Zebra approved rechargeable battery packs are designed and constructed to the highest standards within the industry. However, there are limitations as to how long a battery can operate or be stored before needing replacement. Many factors affect the actual life cycle of a battery pack such as heat, cold, harsh environmental conditions, and severe drops. When batteries are stored over six months, some irreversible deterioration in overall battery quality may occur. Store batteries at half of full charge in a dry, cool place, removed from the equipment to prevent loss of capacity, rusting of metallic parts, and electrolyte leakage. When storing batteries for one year or longer, the charge level should be verified at least once a year and charged to half of full charge. Replace the battery when a significant loss of run time is detected. Standard warranty period for all Zebra batteries is one year, regardless if the battery was purchased separately or included as part of the mobile computer or bar code scanner. For more information on Zebra batteries, please visit:
http://www.zebra.com/batterybasics. Battery Safety Guidelines The area in which the units are charged should be clear of debris and combustible materials or chemicals. Particular care should be taken where the device is charged in a non-commercial environment. Follow battery usage, storage, and charging guidelines found in the user's guide. Improper battery use may result in a fire, explosion, or other hazard. To charge the mobile device battery, the battery and charger temperatures must be between +32 F and +113 F (0 C and +45 C). Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact Zebra support. For devices that utilize a USB port as a charging source, the device shall only be connected to products that bear the USB-IF logo or have completed the USB-IF compliance program. Do not disassemble or open, crush, bend or deform, puncture, or shred. Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat. Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals. Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, or expose to fire, explosion, or other hazard. Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer. Battery usage by children should be supervised. Please follow local regulations to promptly dispose of used re-
chargeable batteries. Do not dispose of batteries in fire. Seek medical advice immediately if a battery has been swallowed. In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice. If you suspect damage to your equipment or battery, contact Zebra support to arrange for inspection. Radio Frequency Interference Requirements
- FCC This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Radio Frequency Interference Requirements
- Canada CAN ICES-3 (B)/NMB-3(B) Radio Transmitters This device complies with Industry Canada's license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio lectrique subi mme si le brouillage est susceptible d'en compromettre le fonctionnement. Marking and European Economic Area (EEA) Bluetooth Wireless Technology for use throughout the EEA has the following restrictions:
Maximum radiated transmit power of 100mW EIRP in the frequency range 2.400 -2.4835 GHz. Statement of Compliance Zebra hereby declares that this radio equipment is in compliance with Directive, 2011/65/EU and 1999/5/EC or 2014/53/EU (2014/53/EU supersedes 1999/5/EC from 13th June 2017). The full text of the EU Declaration of Conformity is available at the following internet address: http://www.zebra.com/doc. Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return product, please go to:
http://www.zebra.com/weee. Franais: Clients de l'Union Europenne: Tous les produits en fin de cycle de vie doivent tre retourns Zebra pour recyclage. Pour de plus amples informations sur le retour de produits, consultez : http://www.zebra.com/
weee. Espaol: Para clientes en la Unin Europea: todos los productos debern entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si desea ms informacin sobre cmo devolver un producto, visite:
http://www.zebra.com/weee. Bulgarish: :
Zebra .
, :
http://www.zebra.com/weee. Deutsch: Fr Kunden innerhalb der EU: Alle Produkte mssen am Ende ihrer Lebensdauer zum Recycling an Zebra zurckgesandt werden. Informationen zur Rcksendung von Produkten finden Sie unter http://www.zebra.com/weee. Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni sulle modalit di restituzione, visitare il seguente sito Web:
http://www.zebra.com/weee. Portugus: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos Zebra para reciclagem. Para obter informaes sobre como devolver o produto, visite:
http://www.zebra.com/weee. Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg http://www.zebra.com/weee voor meer informatie over het terugzenden van producten. Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji naley zwrci do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktw znajduj si na stronie internetowej http://www.zebra.com/weee. etina: Pro zkaznky z EU: Vechny produkty je nutn po skonen jejich ivotnosti vrtit spolenosti Zebra k recyklaci. Informace o zpsobu vrcen produktu najdete na webov strnce: http://www.zebra.com/weee. Eesti: EL klientidele: kik tooted tuleb nende eluea lppedes tagastada taaskasutamise eesmrgil Zebra'ile. Lisainformatsiooni saamiseks toote tagastamise kohta klastage palun aadressi: http://www.zebra.com/weee. Magyar: Az EU-ban vsrlknak: Minden tnkrement termket a Zebra vllalathoz kell eljuttatni jrahasznosts cljbl. A termk visszajuttatsnak mdjval kapcsolatos tudnivalkrt ltogasson el a http://www.zebra.com/weee weboldalra. Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku ivljenjske dobe vrniti podjetju Zebra za reciklao. Za informacije o vrailu izdelka obiite:
http://www.zebra.com/weee. Svenska: Fr kunder inom EU: Alla produkter som uppntt sin livslngd mste returneras till Zebra fr tervinning. Information om hur du returnerar produkten finns p http://www.zebra.com/weee. Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrtettvksi Zebra-yhtin, kun tuotetta ei en kytet. Listietoja tuotteen palauttamisesta on osoitteessa http://www.zebra.com/
weee. Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, nr de er udtjent. Ls oplysningerne om returnering af produkter p: http://www.zebra.com/weee.
: ..: ,
, Zebra
.
, http://www.zebra.com/weee
. Malti: Gal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aar tal-ajja ta'
l-uu taghom, iridu jiu rritornati gand Zebra gar-riikla. Gal aktar tagrif dwar kif gandek tirritorna l-prodott, jekk jogbok ur:
http://www.zebra.com/weee. Romnesc: Pentru clienii din UE: Toate produsele, la sfritul duratei lor de funcionare, trebuie returnate la Zebra pentru reciclare. Pentru informaii despre returnarea produsului, accesai: http://www.zebra.com/
weee. Slovenina: Pre zkaznkov z krajn EU: Vetky vrobky musia by po uplynut doby ich ivotnosti vrten spolonosti Zebra na recyklciu. Bliie informcie o vrten vrobkov njdete na: http://www.zebra.com/
weee. Lietuvi: ES vartotojams: visi gaminiai, pasibaigus j eksploatacijos laikui, turi bti grinti utilizuoti kompanij Zebra. Daugiau informacijos, kaip grinti gamin, rasite:
http://www.zebra.com/weee. Latvieu: ES klientiem: visi produkti pc to kalpoanas ma beigm ir jnogd atpaka Zebra otrreizjai prstrdei. Lai iegtu informciju par produktu nogdanu Zebra, ldzu, skatiet: http://www.zebra.com/weee. Trke: AB Mterileri iin: Kullanm sresi dolan tm rnler geri dntrme iin Zebra'ya iade edilmelidir. rnlerin nasl iade edilecei hakknda bilgi iin ltfen u adresi ziyaret edin: http://www.zebra.com/
weee. TURKISH WEEE Statement of Compliance for All Devices EEE Ynetmeliine Uygundur