EC500K Regulatory Guide Regulatory Information This device is approved under Zebra Technologies Corporation. This guide applies to the following model number: EC500K All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold and will be labeled as required. Local language translation / Traduo do idioma local / bersetzung in die lokale Sprache / Raduccion de idioma local / Traduction en langue locale / Prijevod na lokalni jezik / Traduzione in lingua locale /
/ / / / / Yerel dil eviri
/Tumaczenie na jzyk lokalny : www.zebra.com/support Any changes or modifications to Zebra equipment not expressly approved by Zebra could void the users authority to operate the equipment. Declared maximum operating temperature: 50C Bluetooth Wireless Technology This is an approved Bluetooth product. For more information on the Bluetooth SIG listing, please visit www.bluetooth.com. Regulatory Markings Regulatory markings subject to certification are applied to the device signifying the radio(s) is/are approved for use. Refer to the Declaration of Conformity (DoC) for details of other country markings. The DOC is available at: www.zebra.com/doc. The regulatory marks specific to this device (including FCC and ISED) are available on the screen of the device by following these instructions:
Go to Settings > Regulatory. Health and Safety Recommendations Ergonomic Recommendations In order to avoid or minimize the potential risk of ergonomic injury, always follow good ergonomic workplace practices. Consult with your local Health and Safety Manager to ensure that you are adhering to your companys safety programs to prevent employee injury. Vehicle Installation RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles
(including safety systems). Check with the manufacturer or its representative regarding your vehicle. Ensure the equipment is installed to avoid driver distractions. You should also consult the manufacturer about any equipment that has been added to your vehicle. Position the device within easy reach. User should be able to access the device without removing their eyes from the road. ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corp., registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. 2020 Zebra Technologies Corp. and/or its affiliates. All rights reserved. | www.zebra.com partnumber-xxEN Rev. A REVIEW ONLY 8/31/20 EC500K Regulatory Guide IMPORTANT: Before installing or using, check national and local laws regarding distracted driving. Safety on the Road Give your full attention to driving. Obey the laws and regulations on the use of wireless devices in the areas where you drive. The wireless industry reminds you to use your device / phone safely when driving. Restricted Use Locations Safety in Hospitals and Aircraft Remember to observe restrictions and obey all signs and instructions on the use of electronic devices in restricted use locations. NOTE: Wireless devices transmit radio frequency energy that may affect medical electrical equipment and aircrafts operation. Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics, healthcare facilities or by airline staff. These requests are designed to prevent possible interference with sensitive equipments. RF Exposure Guidelines Safety Information Reducing RF Exposure Use Properly Only operate the device in accordance with the instructions supplied. The device complies with internationally recognized standards covering human exposure to electromagnetic fields. For information on international human exposure to electromagnetic fields, refer to the Zebra Declaration of Conformity (DoC) at www.zebra.com/doc. Use only Zebra tested and approved headset, belt-clips, holsters, and similar accessories to ensure RF exposure compliance. If applicable, follow the instructions for use as detailed in the accessory guide. The use of third-party belt clips, holsters, and similar accessories may not comply with RF exposure compliance requirements and should be avoided. For further information on the safety of RF energy from wireless devices, refer to RF exposure and assessment standards section at www.zebra.com/responsibility. Handheld or Body-Worn Devices To satisfy RF exposure requirements, this device must operate with a minimum separation distance of 1.5 cm or more from a user's body and nearby persons. LED Devices Classified as EXEMPT RISK GROUP according to IEC 62471:2006 and EN 62471:2008. Pulse Duration: 22.8 ms (SE4100) 2 REVIEW ONLY 8/31/20 EC500K Regulatory Guide Power Supply Batteries and Power Packs Battery Information WARNING ELECTRICAL SHOCK: Use only a Zebra approved, Certified ITE [SELV] power supply with appropriate electrical ratings. Use of alternative power supply will invalidate any approvals given to this unit and may be dangerous. This information applies to Zebra-approved batteries and power packs containing batteries. CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of batteries according to instructions. Use only Zebra approved batteries. Accessories which have battery charging capability are approved for use with the following battery models:
Model BT-000424 (3.85 VDC, 3000 mAh) Model BT-000424A (3.85 VDC, 4100 mAh) Zebra approved rechargeable battery packs are designed and constructed to the highest standards within the industry. However, there are limitations as to how long a battery can operate or be stored before needing replacement. Many factors affect the actual life cycle of a battery pack such as heat, cold, harsh environmental conditions, and severe drops. When batteries are stored over six months, some irreversible deterioration in overall battery quality may occur. Store batteries at half charge in a dry, cool place, removed from the equipment to prevent loss of capacity, rusting of metallic parts, and electrolyte leakage. When storing batteries for one year or longer, the charge level should be verified at least once a year and charged to half charge. Replace the battery when a significant loss of run time is detected. Standard warranty period for all Zebra batteries is one year, regardless if the battery was purchased separately or included as part of the host device. For more information on Zebra batteries, please visit:
www.zebra.com/batterydocumentation and select the Battery Best Practices link. Battery Safety Guidelines IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING When using this product basic safety precautions should always be followed, including the following:
The area in which the units are charged should be clear of debris and combustible materials or chemicals. Particular care should be taken where the device is charged in a non-commercial environment. Read all the instructions before using the product. Follow battery usage, storage, and charging guidelines found in the user's guide. Improper battery use may result in a fire, explosion, or other hazard. To charge the mobile device battery, the battery and charger temperatures must be between 0C and +40C (+32F and +104F). 3 REVIEW ONLY 8/31/20 EC500K Regulatory Guide Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact Zebra support. For devices that utilize a USB port as a charging source, the device shall only be connected to products that bear the USB-IF logo or have completed the USB-IF compliance program. Do not disassemble or open, crush, bend or deform, puncture, or shred. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury. Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat. Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals. Do not modify, disassemble, or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water, rain, snow or other liquids, or expose to fire, explosion, or other hazard. Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer. To reduce the risk of injury, close supervision is necessary when used near children. Please follow local regulations to promptly dispose of used re-chargeable batteries. Do not dispose of batteries in fire. Exposure to temperatures over 100C (212F) may cause explosion. Seek medical advice immediately if a battery has been swallowed. In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice. If you suspect damage to your equipment or battery, contact Zebra support to arrange for inspection. Marking and European Economic Area (EEA) Statement of Compliance Zebra hereby declares that this radio equipment is in compliance with Directives 2014/53/EU and 2011/65/EU. Any radio operation limitations within EEA countries are identified in Appendix A of EU Declaration of Conformity. The full text of the EU Declaration of Conformity is available at: www.zebra.com/doc. Waste Electrical and Electronic Equipment (WEEE) For EU Customers: For products at the end of their life, please refer to recycling/disposal advice at:
www.zebra.com/weee. 4 REVIEW ONLY 8/31/20 EC500K Regulatory Guide United States and Canada Regulatory Radio Frequency Interference Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmfulb interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Radio Frequency Interference Requirements Canada Innovation, Science and Economic Development Canada ICES-003 Compliance Label: CAN ICES-3
([B])/NMB-3([B]) This device complies with Innovation, Science and Economic Development Canadas licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio lectrique subi mme si le brouillage est susceptible d'en compromettre le fonctionnement. This device is restricted to indoor use when operating in the 5150 to 5350 MHz frequency range. Lorsqu'il fonctionne dans la plage de frquences 5 150- 5350 MHz, cet appareil doit tre utilis exclusivement en extrieur. RF Exposure Requirements - FCC and ISED The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated in compliance with the FCC RF emission guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid. Handheld Devices To satisfy RF exposure requirements, this device must operate with a minimum separation distance of 1.5 cm or more from a user's body and nearby persons. Pour satisfaire aux exigences d'exposition aux radio frquences, cet appareil doit fonctionner avec une distance de sparation minimale de 1.5 cm ou plus de corps d'une personne. 1 REVIEW ONLY 8/31/20 EC500K Regulatory Guide Co-located Statement To comply with FCC RF exposure compliance requirement, the antenna used for this transmitter must not be co-located (within 20 cm) or operating in conjunction with any other transmitter/antenna except those already approved in this filling. This device is marked HAC showing compliance with the applicable requirements of FCC Part 68 and ISED CS-03-Part 5. UL Listed Products with GPS Underwriters Laboratories Inc. (UL) has not tested the performance or reliability of the Global Positioning System (GPS) hardware, operating software, or other aspects of this product. UL has only tested for fire, shock, or casualties as outlined in ULs Standard(s) for Safety for Information Technology Equipment. UL Certification does not cover the performance or reliability of the GPS hardware and GPS operating software. UL makes no representations, warranties, or certifications whatsoever regarding the performance or reliability of any GPS related functions of this product. Marquage UL des produits quips d'un GPS Les tests mens par Underwriters Laboratories Inc. (UL) ne portent ni sur les performances, ni sur la fiabilit du matriel et du logiciel d'exploitation du GPS (Global Positioning System), ni sur tout autre aspect de ce produit. UL a uniquement test la rsistance au feu, aux chocs et aux sinistres, comme le dfinit la norme UL60950-1 relative la scurit des matriels de traitement de l'information. La certification UL ne couvre ni les performances, ni la fiabilit du matriel et du logiciel d'exploitation GPS. UL ne formule aucune dclaration, ni ne dlivre aucune garantie ni aucun certificat concernant les performances et la fiabilit des fonctions GPS de ce produit. Brasil Este equipamento no tem direito proteo contra interferncia prejudicial e no pode causar interferncia em sistemas devidamente autorizados. Este produto est homologado pela Anatel de acordo com os procedimentos regulamentados para avaliao da conformidade de produtos para telecomunicaes e atende aos requisitos tcnicos aplicados, incluindo os liYDmites de exposio da Taxa de Absoro Especfica referente a campos eltricos, magnticos e eletromagnticos de radiofrequncia. SAR VALUES NEEDED Valores de SAR medidos:
Cabea: xxxx W/kg Corpo: xxxx W/kg 1-model#
2-model#
3-model#
4-model#
5-model#
Valores de SAR medidos N do modelo Cabea W/kg Corpo W/kg xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx 2 REVIEW ONLY 8/31/20 EC500K Regulatory Guide Valores de SAR medidos N do modelo Cabea W/kg Corpo W/kg 6-model#
7-model#
8-model#
xxxx xxxx xxxx xxxx xxxx xxxx Este dispositivo est em conformidade com as diretrizes de exposio a radiofrequncia quando posicionado pelo menos 1.5 cm do corpo. www.zebra.com/support
: www.tenaa.com.cn/.
SAR VALUES NEEDED SAR xxxx W/kg GB 21288-2007 CCC ISM 5000 3 REVIEW ONLY 8/31/20 EC500K Regulatory Guide ROHS TABLE VALUES NEEDED
(Parts)
(Pb)
(Hg)
(Cd)
(Cr(VI))
(PBB)
(PBDE)
(Metal Parts)
(Circuit
(Cables
(Optics
(Print Heads)
(Batteries)
(Ext. Pwr Sply) SJ/T 11364 O: GB/T 26572 X: GB/T 26572 (
Colombia Seor usuario, la siguiente informacin se entrega de conformidad con lo establecido en el Rgimen de proteccin de los derechos de los usuarios, expedido por la Comisin de Regulacin de Comunicaciones. Recomendaciones de uso:
1. Utilice siempre que pueda dispositivos manos libres. 2. Evite utilizar el equipo mientras conduce un vehculo. 3. En caso que el telfono sea utilizado por nios, ancianos, mujeres embarazadas y poblacin inmunocomprometida, consulte a su mdico y el manual del equipo. 4. Si usted utiliza algn dispositivo electrnico de uso mdico, asegrese que el mismo est protegido contra las ondas de radiofrecuencia externas. 5. Apague su telfono en lugares tales como: hospitales, centros de salud, aviones, estaciones de suministro de combustible, en presencia de gases explosivos y lugares donde se realizan explosiones. 6. Evite que terceros hagan uso de su telfono para prevenir la implantacin de dispositivos como programas espas (spyware) o identificadores ocultos, que atentan contra la seguridad de la informacin contenida en el mismo.
(EAC) EAC. 4 REVIEW ONLY 8/31/20 EC500K Regulatory Guide France India Mxico Cet appareil a t test et dclar conforme aux limites applicables d'exposition aux radiofrquences (RF). Le dbit d'absorption spcifique (DAS) local quantifie l'exposition de l'utilisateur aux ondes lectromagntiques de l'quipement concern. Les valeurs SAR les plus leves sont disponibles sur la dclaration de conformit (DoC) disponible sur:
www.zebra.com. The sending and receiving of texts is supported in the following Indian languages:
Assamese, Bengali, Gujarati, Hindi, Kannada, Kashmiri, Konkani, Malayalam, Manipuri, Marathi, Nepali, Oriya, Punjabi, Sanskrit, Sindhi, Tamil, Telugu, Urdu, Bodo, Santhali, Maithili, and Dogri. La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada.
: EC500K
: xxxx W/kg
(SAR : Specified Absorption Rate) 2 W/kg 1.6 W/kg .
(www.rra.go.kr)
1 2
SAR
www.rra.go.kr
SAR
www.rra.go.kr
5 REVIEW ONLY 8/31/20 EC500K Regulatory Guide xxxx mm .
/ 9 13
(EPA) 15
(Product Description in CHINESE Equipment name) Model Type designation (Type) Restricted substances and its chemical symbols
(Pb)
(Hg)
(Cd)
(Cr+6)
(PBB)
(PBDE) ROHS TABLE VALUES NEEDED Unit 1. 0.1 wt % 0.01 wt %
2. O 3. Note 1: Exceeding 0.1 wt% and exceeding 0.01 wt% indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition. Note 2: O indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence. Note 3: The indicates that the restricted substance corresponds to the exemption. Trkiye Bu cihaz Trke karakterlerin tamamn ihtiva eden ETSI TS 123.038 V8.0.0 (veya sonraki srmnkodu) ve ETSI TS 123.040 V8.1.0 (veya sonraki srmn kodu) teknik zelliklerine uygundur. TRK WEEE Uyumluluk Beyan EEE Ynetmeliine Uygundur. 6 REVIEW ONLY 8/31/20 EC500K Regulatory Guide
(Specific Absorption Rate SAR) EC500K 1.141 w/kg Warranty Service Information For the complete Zebra hardware product warranty statement, go to: zebra.com\warranty. Before you use the unit, it must be configured to operate in your facility's network and run your applications. If you have a problem running your unit or using your equipment, contact your facility's Technical or System Support. If there is a problem with the equipment, they will contact Zebra support at zebra.com\support. For the latest version of the guide go to: zebra.com\support. Software Support Additional Information For information on using the EC500K, refer to the EC500K product guide available at: zebra.com/support. 7 REVIEW ONLY 8/31/20 EC500K Regulatory Guide Warranty Service Information Software Support For the complete Zebra hardware product warranty statement, go to: zebra.com\warranty. Before you use the unit, it must be configured to operate in your facility's network and run your applications. If you have a problem running your unit or using your equipment, contact your facility's Technical or System Support. If there is a problem with the equipment, they will contact Zebra support at zebra.com\support. For the latest version of the guide go to: zebra.com\support. Zebra wants to ensure that customers have the latest entitled software at the time of device purchase in order to keep the device operating at peak performance levels. To confirm that your Zebra device has the latest entitled software available at the time of purchase, visit www.zebra.com/support. Check for the latest software from Support > Products, or search for the device and select Support >
Software Downloads. If your device does not have the latest entitled software as of your device purchase date, e-mail Zebra at entitlementservices@zebra.com and ensure you include the following essential device information:
Model number Serial number Proof of purchase Title of the software download you are requesting. If it is determined by Zebra that your device is entitled to the latest version of software, as of the date you purchased your device, you will receive an e-mail containing a link directing you to a Zebra Web site to download the appropriate software. Additional Information For information on using the family name, refer to the family name product guide available at: web address. 13 REVIEW ONLY 8/31/20