FCC ID: UZ7RS507 Hands-Free Imager, BT Barcode Scanner

QRG_507.fm Page 1 Wednesday, January 28, 2009 8:37 PM RS507 Hands-Free Imager Quick Reference Guide QRG_507.fm Page 2 Wednesday, January 28, 2009 8:37 PM 2 RS507 Hands-Free Imager 2009 MOTOROLA, INC. All rights reserved. Motorola reserves the right to make changes to any product to improve reliability, function, or design. Motorola does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Motorola products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Motorola products. MOTOROLA and the Stylized M Logo are registered trademarks of Motorola, Inc. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. Motorola, Inc. One Motorola Plaza Holtsville, N.Y. 11742-1300 www.motorola.com/enterprisemobility. Warranty For the complete Motorola hardware product warranty statement, go to:

www.motorola.com/enterprisemobility/warranty. Patents This product is covered by one or more patents. For patent information go to:

www.motorola.com/enterprisemobility/patents. QRG_507.fm Page 3 Wednesday, January 28, 2009 8:37 PM Quick Reference Guide 3 Introduction The RS507 Hands-Free Imager (also referred to as Imager) is wearable barcode scan solution for both 1D and 2D barcode symbologies. The Imager is also compatible with a wide range of mobile computers communicating over Bluetooth. The Imager is designed for a wide range of applications from management of products in a warehouse, processing deliveries at a courier facility, hospitality to scanning lift tickets at a ski resort. The Imager uses camera-based scanning technology, designed to offer flexible hands-free operation with ergonomic comfort for right or left hand users. The Imager can be operated in both manual and auto-triggering modes. Auto-triggering is a patented Intelligent Sensing Technology combining motion and proximity sensing for triggering the Imager. The Imager durability is built to last and rated for indoor and outdoor daily use in intensive scan environments. Built on magnesium chassis, the Imager offers durability associated with the most rugged mobile computers. About this Guide This guide provides basic information on the following topics:

Cordless Configuration Features on page 5 Change Trigger Position on page 7 Getting Started - Cordless Configuration on page 8 Getting Started - Corded Configuration on page 9 Establish Bluetooth Connection on page 11 Scan on page 13 Status Indications on page 11 Troubleshooting on page 16 Resetting the Imager on page 17 Field Replaceable Parts on page 18 Cleaning on page 21 Ergonomic Recommendations on page 24 Regulatory Information on page 23 Waste Electrical and Electronic Equipment (WEEE) on page 34 For more information, refer to the RS507 Hands-Free Imager Product Reference Guide, p/n 72-120802-01 available at:

www.motorola.com/enterprisemobility/manuals. QRG_507.fm Page 4 Wednesday, January 28, 2009 8:37 PM 4 RS507 Hands-Free Imager Unpacking the Imager After opening the shipping box, inspect the contents. You should have received the following:

Model Description RS507 Standard Battery Extended Battery Corded Adapter Quick Start Guide RS507-IM200000STWR Triggered RS507 with standard battery RS507-IM200000SNWR Triggerless RS507 with standard battery RS507-IM200000ENWE Triggerless RS507 with extended battery RS507-IM200000CTWR Corded and Triggered RS507 Inspect the equipment for damage. If you are missing any equipment or if you find any damaged equipment, contact Motorola Enterprise Mobility Support immediately. See Service Information on backcover for contact information. QRG_507.fm Page 5 Wednesday, January 28, 2009 8:37 PM Quick Reference Guide 5 Cordless Configuration Features NOTE When the imager is provided as triggerless configuration, the auto-triggering mode is enabled by default. Imager Window Battery Release Latch Battery Comfort Pad Fingers Strap Trigger Assembly Scan Trigger Asset Control Label Restore Key Left Scan LED Strap Buckle Beeper Right Scan LED Strap QRG_507.fm Page 6 Wednesday, January 28, 2009 8:37 PM 6 RS507 Hands-Free Imager Corded Configuration Features Interface Cable Connector to WT4090 Release Latch Imager Window Comfort Pad Corded Adapter Trigger Assembly Fingers Strap Scan Trigger Asset Control Label Restore Key Strap Buckle Strap Left Scan LED Beeper Right Scan LED QRG_507.fm Page 7 Wednesday, January 28, 2009 8:37 PM Quick Reference Guide 7 Change Trigger Position The Trigger Assembly of the Imager rotates to provide left-hand or right-hand use. 1. Remove the Fingers Strap from the Strap Buckle. 2. From bottom of Imager, Hold and pull the Comfort Pad out of the Barcode Imager. Fingers Strap Trigger Assembly Comfort Pad Strap Buckle 3. Determine whether the Imager is used on the right or left hand and rotate the Trigger Assembly. Trigger Assembly CAUTION The Trigger Assembly only rotates 180 around the back of the scan assembly. Do not rotate the Trigger Assembly past the designed stops 4. Rotate the Trigger Assembly so that the Scan Trigger is positioned next to the thumb when the Imager is placed on the index and middle fingers. 5. Position the Comfort Pad onto the Imager. 6. Press the Comfort Pad onto the Imager. When properly installed, the Comfort Pad locks into place. Insert the Fingers Strap into the Strap Buckle 7. QRG_507.fm Page 8 Wednesday, January 28, 2009 8:37 PM 8 RS507 Hands-Free Imager Getting Started - Cordless Configuration Before using the Imager, charge the battery. The 8-Bay Battery Charger supports both standard and extended capacity batteries. Charge the Battery To charge the Imager battery, refer to SAC5070 Quick Start Guide. Install the Battery 1. Align the Battery on top of the Imager. 2. Push the battery all the way into the Locking Slots of the Imager. 3. Firmly press the Battery into the Imager until a click is heard ensuring the Battery Release Latch is fully engaged with the Imager. Battery Release Latch Battery Remove the Battery 1. Hold the Imager in one hand. 2. Press the Battery Release Latch. 3. Pull up the Battery to release from the Locking Slots of the Imager. Wear the Imager 1. Slide the Imager onto the index and middle fingers with the Scan Trigger next Locking Slots to the thumb. Scan Trigger QRG_507.fm Page 9 Wednesday, January 28, 2009 8:37 PM Quick Reference Guide 2. Tighten the Fingers Strap. 9 Fingers Strap aaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaa Getting Started - Corded Configuration In order to start using the Imager you must install the Corded Adapter. Connect Corded Adapter 1. Align the Corded Adapter on top of the Adapter Release Imager. Latch 2. Push the Corded Adapter all the way into the Locking Slots of the Imager. 3. Firmly press the Corded Adapter into the Imager until a click is heard ensuring the Adapter Release Latch is fully engaged with the Imager. Remove the Corded Adapter 1. Hold the Imager in one hand. 2. Press the Adapter Release Latch. 3. Pull up the Corded Adapter to release from the Locking Slots of the Imager. Corded Adapter Locking Slots QRG_507.fm Page 10 Wednesday, January 28, 2009 8:37 PM 10 RS507 Hands-Free Imager Connect to a Wearable Terminal The Imager connects to the WT4090 and mounts on the fingers. 1. On the WT4090, remove the Interface Cable Connector connector cover. WT4090 Interface Connector 2. Connect the Imager Interface Cable Connector to the WT4090 Interface Connector. Wear the Imager 1. Slide the Imager onto the index and middle fingers with the Scan Trigger next to the thumb. Scan Trigger 2. Tighten the Fingers Strap. Fingers Strap 4tQ aaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaa QRG_507.fm Page 11 Wednesday, January 28, 2009 8:37 PM Quick Reference Guide 11 Status Indications The Imager has two Scan LEDs that provide identical indications. The Imager is also equipped with a beeper that generates sound indications in variable tones. NOTE In corded adapter configuration, beep indications are emitted only from the WT4090. LED Beep Indication Description No. 1. 2. 3. 4. 5. 6. 7. 8. 9. None High/low Short green flashes None None None None None None Low/high High/low high/low/high/low Long low/

long high/

Long low/

long high/

Long low/

long high/

Bluetooth communication is disconnected Attempting to connect over Bluetooth Imager is connected over Bluetooth Bluetooth communication is disconnected - Imager is out of range Properly decoded scan of Bluetooth pairing Barcode Bluetooth connection attempt failed Bluetooth connection attempt is rejected One green flash High None 4 long beeps Proper scanning indication No Bluetooth communication after scanning time-out Bluetooth Connection Establish Bluetooth Connection To establish Bluetooth connection with a mobile computer:

1. Ensure that the Imager is within a range of 10 meters (30 feet) from the mobile computer. Install the battery on the Imager. 2. QRG_507.fm Page 12 Wednesday, January 28, 2009 8:37 PM 12 RS507 Hands-Free Imager 3. Launch the Bluetooth Device (BD) Address application on the mobile computer. Most BD Address applications display a pairing barcode image on the screen of the mobile computer. 4. Scan a pairing barcode form the mobile computer screen or any provided label. When scanning, the Imager emits one string of high/low/high/low beeps. 5. The Scan LED starts flashing green indicating that the Imager is attempting to establish connection with a mobile computer. 6. When connection is established, the Scan LED turns Off and the Imager emits one string of low/high beeps. The Imager is connected and ready for scanning. NOTE When replacing the Imager battery, the Imager memory retains the pairing information of last paired mobile computer (e.g WT4090). Remove Bluetooth Connection 1. Scan an unpairing barcode label with the Bluetooth address for disconnecting the Imager from the mobile computer (e.g WT4090). 2. The Imager emits one string of high/low beeps indicating that Bluetooth communication with the mobile computer is disconnected. Restore Lost Bluetooth Connection The Imager maintains Bluetooth communication with a mobile computer within a range of 10 meters (30 feet). When the Imager fails to establish connection or connection is lost during operation, the Imager emits one string of low/high beeps. To reestablish Bluetooth connection with a mobile computer (e.g WT4090):

1. Ensure that the Imager is within a range of 10 meters (30 feet) from the mobile computer. 2. Ensure that the mobile computer is On and awake (not in Suspend mode). 3. The Imager automatically attempts reconnecting to the mobile computer for 30 seconds (Scan LED flashes green). If automatic re-connection fails, verify that the Imager is within Bluetooth range and briefly press the Restore Key on the Imager to reconnect. 4. The Scan LED starts flashing green indicating that the Imager is attempting to establish connection with a mobile computer (e.g WT4090). 5. The Scan LED turns Off and the Imager emits one string of low/high beeps indicating that the Imager is connected and ready for scanning. QRG_507.fm Page 13 Wednesday, January 28, 2009 8:37 PM Quick Reference Guide 13 Scan The Imager uses digital camera technology to take a picture of a barcode and software decoding algorithms are executed to extract the barcode data from the image. Scan Triggering Modes Manual Triggering (Triggered models only) 1. Launch a scanning software application on the mobile computer or WT4090. 2. Press the Scan Trigger and position the aiming cross hair laser to cover the barcode. The Imager takes a digital picture (image) of the barcode and stores it in memory for decoding. 3. One green flash and a high beep sounds to indicate that the barcode was properly decoded. NOTE In some configurations proper decoding of a barcode is indicated by software application running on mobile computer or WT4090. Auto-triggering (Triggered models only) The Imager is provided with auto-triggering capability. In auto-triggering mode, both motion and proximity sensors are used to trigger the Imager when the user intends to scan a barcode. With auto-triggering activated, the Imager automatically scans when motion stops and a barcode is placed within the depth of field of the Imager. The Imager scans the barcode and turns off to conserve power. To scan barcode in auto-triggering mode:

1. Bring the Imager within 9 inches 1 inch (22.86 cm 2.54 cm) of a barcode label. 2. Hold the Imager steady, aiming at the barcode label. 3. The Imager takes a picture (image) of the barcode and stores it in memory for decoding. 4. One green flash of the Scan LED and a high beep indicates that a barcode was properly decoded. NOTE In some configurations, proper decoding of a barcode is indicated by a software application running on mobile computer or WT4090. QRG_507.fm Page 14 Wednesday, January 28, 2009 8:37 PM 14 RS507 Hands-Free Imager Aiming the Imager The aimer of the Imager is a cross hair laser with bright center dot (shown below). The virtual rectangle made by the Cross Hair Lines reflects the field of view of the Imager. The aimer is used to position the barcode or object within the field of view. Cross Hair Lines of Imager Aimer Virtual rectangle made by the Cross Hair Lines 1. Enter the symbol in any orientation within the virtual rectangle made by the cross hair lines. Linear Barcode PDF417 Symbol

@

4 3 2 1

@

Symbol Aimer Pattern The imager can also read a barcode presented within the aiming pattern but not centered, such as the figure below on the left. The figure on the right, however, may not be decoded.

@1234@

Right

@1234@

Wrong The aiming pattern is smaller when the Imager is closer to the symbol and larger when it is farther from the symbol. Scan symbols with smaller bars or elements (mil size) closer to the unit and those with larger bars or elements

(mil size) farther from the unit. 2. Hold the Imager between two and eleven inches (depending on symbol density) from the symbol, centering the aiming pattern cross hairs on the symbol. 3. Press the Scan Button. The aimer pattern illuminates red indicating that the Laser is on. One green flash of the Scan LED and a high beep indicates that a barcode was properly decoded. QRG_507.fm Page 15 Wednesday, January 28, 2009 8:37 PM Quick Reference Guide 15 Customize the Imager Behavior The Imager behavior can be configured by scanning custom barcode tables. The following table provides examples of configurable Imager features. Feature Description Beep on reconnection attempt When this parameter is enabled, the Imager emits a low/high beep when Bluetooth link is reconnected. Default Setting The beep on reconnection attempt feature is disabled by default. Motion sensing Proximity sensing When this parameter is enabled, the Imager automatically scans when motion stops in front of the Imager and a barcode is placed within the depth of field of the Imager. Motion sensing is set by default to on for triggerless models and off for triggered models. When this parameter is enabled, the Imager automatically scans when sensing proximity to an object and a barcode is placed within the depth of field of the Imager. Proximity sensing is set by default to on for trigger less models and off for triggered models. Proximity distance When using proximity sensing, you can set proximity distance to Short, Mid or Long. Proximity distance is set to Long by default. Low battery indication When this parameter is enabled, the Imager flashes red every 15 seconds when battery power is low. Low battery indication is disabled by default. Bluetooth auto connect The Imager automatically tries to reconnect to a remote device when a disconnection occurs that is due to the radio losing communication. This can happen if the Imager goes out of the mobile computer range. The following auto connect options are available: None, On power up, Back in Bluetooth range, On power up & back in Bluetooth range. Bluetooth auto connect is set to Back in Bluetooth range by default. QRG_507.fm Page 16 Wednesday, January 28, 2009 8:37 PM 16 RS507 Hands-Free Imager Troubleshooting Problem Cause Solution Laser aimer does not display when pressing the Scan Trigger Corded: Interface cable is not secure Cordless: Battery is not charged Power is not applied to Imager Verify that the interface cable is properly connected Replace or charge battery Corded: Verify that the mobile computer (e.g WT4090) has a charged battery installed Imager does not decode a barcode Scan application on the mobile computer

(e.g WT4090) is not functioning Imager software does not respond Barcode is unreadable Exit window is dirty Barcode symbology is not supported or enabled Cordless: Bluetooth link is disconnected Cordless: Replace or Charge Imager battery Restart the scanning application on the mobile computer (e.g WT4090) Reset the Imager (See Resetting the Imager on page 17) Verify that the barcode is not defective, i.e., smudged or broken Clean exit window with a lens tissue. Tissues for eyeglasses work well. Do not use tissues coated with lotion See your system administrator Reestablish Bluetooth connection

(See Establish Bluetooth Connection on page 11) QRG_507.fm Page 17 Wednesday, January 28, 2009 8:37 PM Quick Reference Guide 17 Resetting the Imager If the Imager stops responding to input, reset it. There are two reset functions, warm boot and cold boot. Perform a warm boot first. If the Imager still does not respond, perform a cold boot. Warm Boot To perform warm boot, press and hold the Restore Key for more than six seconds. Cold Boot Cold boot restores the Imagers operation by resetting its software. To perform cold boot, remove and re-insert the battery into the Imager. When using a corded RS507 model with WT4090, remove and reconnect the interface cable that connects between the Imager and the WT4090. QRG_507.fm Page 18 Wednesday, January 28, 2009 8:37 PM 18 RS507 Hands-Free Imager Field Replaceable Parts Part CLMPT-RS507-R KT-BKL-RS507-R CLMPN-RS507-R KT-PAD-RS507-R Description Trigger Assembly Set of 10 Strap Buckles Triggerless Fingers Clamp Set of 10 Comfort Pads KT-STRPN-RS507-R KT-STRPT-RS507-R BTRY-RS50EAB00-01 Set of 10 Triggerless Fingers Strap with Fingers Support Set of 10 Trigger Fingers Strap with Fingers Support Standard Battery BTRY-RS50EAB02-01 Extended Battery ADPTRWT -RS507-R Corded Adapter 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 8 7 a Fingers Support 9 QRG_507.fm Page 19 Wednesday, January 28, 2009 8:37 PM Quick Reference Guide 19 Comfort Pad Replacement Removal Hold and pull Comfort Pad out of the Barcode Imager. Installation 1. Position the Comfort Pad onto the Imager as shown. 2. Press the Comfort Pad onto the Imager. When properly installed, the Comfort Pad locks into place. Trigger Assembly Replacement 3 Imager Back 1 Release Latch 2 2 1 Triggerless Finger Clamp Removal 1. Turn the Imager upside-down. 2. Remove the Comfort Pad. 3. Rotate the Trigger Assembly to align with the back of the Imager. 4. Use a paper clip or similar object to press the Release Latch. 5. Lift the Trigger Assembly off the scan assembly. Installation 1. Turn the Imager upside-down. 2. Position the Trigger Assembly to align with the back of the Imager. 3. Lower the Trigger Assembly to the scan assembly. 4. Rotate Trigger Assembly 1/4 turn counterclockwise. 5. Press the Comfort Pad onto the Imager. When properly installed, the Comfort Pad locks into place. QRG_507.fm Page 20 Wednesday, January 28, 2009 8:37 PM 20 RS507 Hands-Free Imager Note: An optional Triggerless Finger Clamp should be installed when the Imager is intended to be used in Motion and Proximity Initiated Barcode Read mode. Fingers Strap Replacement (Trigger Assembly) Removal 1. Remove the Fingers Strap from the Strap Buckle. 2. Pull the Fingers Strap out of the Trigger Assembly. Fingers Strap Installation 1. Align a new Finger Strap with the Slots in the Trigger Assembly. 2. Gently press the Strap Pins to engage with the Slots of the Trigger Assembly. The Strap Pins snap into the Slots. 3. Slip the Fingers Strap through the Strap Buckle. Strap Pins Trigger Assembly Slots Strap Buckle QRG_507.fm Page 21 Wednesday, January 28, 2009 8:37 PM Quick Reference Guide 21 Fingers Strap Replacement (Triggerless Finger Clamp) Removal 1. Remove the Fingers Strap from the Strap Buckles. Installation 1. Slip the Fingers Strap through the Strap Buckles. Strap Buckle Replacement Removal Press the Strap Buckle out of the Trigger Assembly Pin. Installation 1. Align the pin slots of Strap Buckle with the pin of the Trigger Assembly. Strap Buckles Strap Buckle Trigger Assembly Pin 2. Gently press the pin slots of Strap Buckle to engage with the pin of the Trigger Assembly. The pin slots snaps into the pin. Cleaning Wipe the exit window periodically with a lens tissue or other material suitable for cleaning eyeglasses. CAUTION Do not pour, spray, or spill any liquid on the Imager. QRG_507.fm Page 22 Wednesday, January 28, 2009 8:37 PM 22 RS507 Hands-Free Imager The gold plated battery contacts do not tarnish or oxidize. No maintenance should be needed. If the contacts need to be cleaned:

1. Wet the tip of a cotton swab with isopropyl alcohol and squeeze the excess alcohol from the swab. 2. Wipe the metal contacts with the damp swab. QRG_507.fm Page 23 Wednesday, January 28, 2009 8:37 PM Quick Reference Guide 23 Regulatory Information This device is approved under the Enterprise Mobility business of Motorola, Inc.

("Motorola"). This guide applies to Model Number RS507. All Motorola devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Local language translations are available at the following website:

www.motorola.com/enterprisemobility/support.. CAUTION Any changes or modifications to Motorola equipment, not expressly approved by Motorola, could void the user's authority to operate the equipment. Only use Motorola approved and UL Listed accessories, battery packs and battery chargers. Do NOT attempt to charge damp/wet mobile computers or batteries. All components must be dry before connecting to an external power source. Bluetooth Wireless Technology This is an approved Bluetooth product. For more information or to view End Product Listing, please visit http://www.bluetooth.org/tpg/listings,cfm Wireless Device Country Approvals Regulatory markings, subject to certification, are applied to the device signifying the radio(s) is/are approved for use in the following countries: United States, Canada, Japan, China, S. Korea, Australia, and Europe (see note below). Please refer to the Motorola Declaration of Conformity (DoC) for details of other country markings. This is available at http://www2.symbol.com/doc/. Note: For 2.4GHz Products: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. QRG_507.fm Page 24 Wednesday, January 28, 2009 8:37 PM 24 RS507 Hands-Free Imager Health and Safety Recommendations Ergonomic Recommendations CAUTION In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health &

Safety Manager to ensure that you are adhering to your companys safety programs to prevent employee injury. Reduce or eliminate repetitive motion Maintain a natural position Reduce or eliminate excessive force Keep objects that are used frequently within easy reach Perform tasks at correct heights Reduce or eliminate vibration Reduce or eliminate direct pressure Provide adjustable workstations Provide adequate clearance Provide a suitable working environment Improve work procedures. Warnings for Use of Wireless Devices Please observe all warning notices with regard to the usage of wireless devices. Potentially Hazardous Atmospheres - Vehicles Use You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals or particles (such as grain, dust, or metal powders) and any other area where you would normally be advised to turn off your vehicle engine. Safety in Hospitals Wireless devices transmit radio frequency energy and may affect medical electrical equipment. QRG_507.fm Page 25 Wednesday, January 28, 2009 8:37 PM Quick Reference Guide 25 Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics or healthcare facilities. These requests are designed to prevent possible interference with sensitive medical equipment. Pacemakers Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with independent research and recommendations by Wireless Technology Research. Persons with Pacemakers:

Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON. Should not carry the device in a breast pocket. Should use the ear furthest from the pacemaker to minimize the potential for interference. If you have any reason to suspect that interference is taking place, turn OFF your device. Other Medical Devices Please consult your physician or the manufacturer of the medical device, to determine if the operation of your wireless product may interfere with the medical device. RF Exposure Guidelines Safety Information Reducing RF Exposure - Use Properly Only operate the device in accordance with the instructions supplied. International The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. For information on

"International" human exposure to electromagnetic fields refer to the Motorola Declaration of Conformity (DoC) at http://www2.symbol.com/doc/. QRG_507.fm Page 26 Wednesday, January 28, 2009 8:37 PM 26 EU RS507 Hands-Free Imager Handheld Devices This device was tested for typical body-worn operation. Use only Motorola tested and approved belt-clips, holsters, and similar accessories to ensure EU Compliance. US and Canada Handheld Devices This device was tested for typical body-worn operation. Use only Motorola tested and approved belt-clips, holsters, and similar accessories to ensure FCC Compliance. The use of third-party belt-clips, holsters, and similar accessories may not comply with FCC RF exposure compliance requirements, and should be avoided. Laser Devices Complies with 21CFR1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001, and with EN60825-1:1994+A1:2002+A2:2001 and IEC60825-1:1993+A1:1997+A2:2001. The laser classification is marked on one of the labels on the device. Class 1 Laser devices are not considered to be hazardous when used for their intended purpose. The following statement is required to comply with US and international regulations:

Caution: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure. Class 2 laser Imagers use a low power, visible light diode. As with any very bright light source, such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful. LASER LIGHT DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT LASERSTRAHLUNG NICHT IN DEN STRAHL BLICKEN LASER KLASSE 2 LUMIRE LASER NE PAS REGARDER DANS LE FAISCEAU APPAREIL LASER DE CLASSE 2 QRG_507.fm Page 27 Wednesday, January 28, 2009 8:37 PM Quick Reference Guide Imager Labeling 27 Country Stamp

(example) Batteries Taiwan - Recycling EPA (Environmental Protection Administration) requires dry battery producing or importing firms in accordance with Article 15 of the Waste Disposal Act are required to indicate the recycling marks on the batteries used in sales, giveaway or promotion. Contact a qualified Taiwanese recycler for proper battery disposal. Battery Information Motorola rechargeable battery packs are designed and constructed to the highest standards within the industry. However, there are limitations to how long a battery can operate or be stored before needing replacement. Many factors affect the actual life cycle of a battery pack, such as heat, cold, harsh environmental conditions and severe drops. QRG_507.fm Page 28 Wednesday, January 28, 2009 8:37 PM 28 RS507 Hands-Free Imager When batteries are stored over six (6) months, some irreversible deterioration in overall battery quality may occur. Store batteries at half of full charge in a dry, cool place, removed from the equipment to prevent loss of capacity, rusting of metallic parts and electrolyte leakage. When storing batteries for one year or longer, the charge level should be verified at least once a year and charged to half of full charge. Replace the battery when a significant loss of run time is detected. Standard warranty period for all Motorola batteries is 3 months, regardless if the battery was purchased separately or included as part of the mobile computer or bar code scanner. For more information on Motorola batteries, please visit:

http:/mysymbolcare.symbol.com/battery/batbasics1.html Battery Safety Guidelines The area in which the units are charged should be clear of debris and combustible materials or chemicals. Particular care should be taken where the device is charged in a non commercial environment. Follow battery usage, storage, and charging guidelines found in the user's guide. Improper battery use may result in a fire, explosion, or other hazard. To charge the mobile device battery, the battery and charger temperatures must be between +32 F and +104 F (0 C and +40 C) Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact Motorola Enterprise Mobility support. Do not disassemble or open, crush, bend or deform, puncture, or shred. Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat. Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals. Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, or expose to fire, explosion, or other hazard. Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer. Battery usage by children should be supervised. QRG_507.fm Page 29 Wednesday, January 28, 2009 8:37 PM Quick Reference Guide 29 Please follow local regulations to promptly dispose of used re-chargeable batteries. Do not dispose of batteries in fire. Seek medical advice immediately if a battery has been swallowed. In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice. If you suspect damage to your equipment or battery, contact Motorola Enterprise Mobility support to arrange for inspection. In accordance with Clause 5, IEC 825 and EN60825, the following information is provided to the user:

QRG_507.fm Page 30 Wednesday, January 28, 2009 8:37 PM 30 RS507 Hands-Free Imager Radio Frequency Interference Requirements-FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna Connect the equipment into an outlet on a circuit different from that to which Increase the separation between the equipment and receiver the receiver is connected Consult the dealer or an experienced radio/TV technician for help. Radio Transmitters (Part 15) - USA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Radio Frequency Interference Requirements - Canada This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Radio Transmitters - Canada This device complies with RSS 210 of Industry & Science Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Label Marking: The Term IC: before the radio certification only signifies that Industry Canada technical specifications were met. QRG_507.fm Page 31 Wednesday, January 28, 2009 8:37 PM Quick Reference Guide 31 Marking and European Economic Area (EEA) Bluetooth Wireless Technology for use through the EEA has the following restrictions:

Maximum radiated transmit power of 100mW EIRP in the frequency range 2.400 -2.4835 GHz Italy requires a user license for outside usage. France, outside usage is restricted to 10mW EIRP Statement of Compliance for Wireless Devices Motorola hereby, declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of Conformity may be obtained from http://www2.symbol.com/doc/. Japan (VCCI) - Voluntary Control Council for Interference Class B ITE This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used QRG_507.fm Page 32 Wednesday, January 28, 2009 8:37 PM 32 RS507 Hands-Free Imager near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. Korea Warning Statement for Class B ITE Other Countries Declaraes Regulamentares para RS507 - Brazil Note: The certification mark applied to the RS507 is for Restrict Radiation Equipment. This equipment operates on a secondary basis and does not have the right for protection against harmful interference from other users including same equipment types. Also this equipment must not cause interference to systems operating on primary basis. For more information consult the website www.anatel.gov.br. Nota: "A marca de certificao se aplica ao Transceptor, modelo RS507. Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio."

Para maiores informaes sobre ANATEL consulte o site: www.anatel.gov.br. Mexico Restrict Frequency Range to: 2.450 - 2.4835 GHz. Sri Lanka- Restrict Frequency Range to: 2.400 - 2.430 GHz. Taiwan -

According to Administrative Regulations on Low Power Radio Waves Radiated Devices:

Article 12 Without permission granted by the DGT, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original QRG_507.fm Page 33 Wednesday, January 28, 2009 8:37 PM Quick Reference Guide 33 characteristic as well as performance to an approved low power radio-frequency devices. Article 14 The low power radio-frequency devices shall not influence aircraft security and interfere legal communications; If found, the user shall cease operating immediately until no interference is achieved. The said legal communications means radio communications is operated in compliance with the Telecommunications Act. The low power radio-frequency devices must be susceptible with the interference from legal communications or ISM radio wave radiated devices. 2.400 - 2.4835 GHz

: 27dBm 5.250 - 5.350 GHz 5.725 - 5.850 GHz 2.4GHz 11 50 GHz Korea QRG_507.fm Page 34 Wednesday, January 28, 2009 8:37 PM 34 RS507 Hands-Free Imager Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to Motorola for recycling. For information on how to return product, please go to:

www.motorola.com/recycling/weee. Bulgarish: :

Motorola .

, :

www.motorola.com/recycling/weee. Dansk: Til kunder i EU: Alle produkter skal returneres til Motorola til recirkulering, nr de er udtjent. Ls oplysningerne om returnering af produkter p:

www.motorola.com/recycling/weee. Deutsch: Fr Kunden innerhalb der EU: Alle Produkte mssen am Ende ihrer Lebensdauer zum Recycling an Motorola zurckgesandt werden. Informationen zur Rcksendung von Produkten finden Sie unter www.motorola.com/recycling/weee. Eesti: EL klientidele: kik tooted tuleb nende eluea lppedes tagastada taaskasutamise eesmrgil Motorola'ile. Lisainformatsiooni saamiseks toote tagastamise kohta klastage palun aadressi: www.motorola.com/recycling/weee. Espaol: Para clientes en la Unin Europea: todos los productos debern entregarse a Motorola al final de su ciclo de vida para que sean reciclados. Si desea ms informacin sobre cmo devolver un producto, visite:

www.motorola.com/recycling/weee. Franais: Clients de l'Union Europenne : Tous les produits en fin de cycle de vie doivent tre retourns Motorola pour recyclage. Pour de plus amples informations sur le retour de produits, consultez :

www.motorola.com/recycling/weee. Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Motorola al fine di consentirne il riciclaggio. Per informazioni sulle modalit di restituzione, visitare il seguente sito Web:

www.motorola.com/recycling/weee. QRG_507.fm Page 35 Wednesday, January 28, 2009 8:37 PM Quick Reference Guide 35 Magyar: Az EU-ban vsrlknak: Minden tnkrement termket a Motorola vllalathoz kell eljuttatni jrahasznosts cljbl. A termk visszajuttatsnak mdjval kapcsolatos tudnivalkrt ltogasson el a www.motorola.com/recycling/weee weboldalra. Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Motorola te worden teruggezonden voor recycling. Raadpleeg www.motorola.com/recycling/weee voor meer informatie over het terugzenden van producten. Portugus: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos Motorola para reciclagem. Para obter informaes sobre como devolver o produto, visite: www.motorola.com/recycling/weee. Romnesc: Pentru clienii din UE: Toate produsele, la sfritul duratei lor de funcionare, trebuie returnate la Motorola pentru reciclare. Pentru informaii despre returnarea produsului, accesai: www.motorola.com/recycling/weee. Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku ivljenjske dobe vrniti podjetju Motorola za reciklao. Za informacije o vrailu izdelka obiite:

www.motorola.com/recycling/weee. Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrtettvksi Motorola-yhtin, kun tuotetta ei en kytet. Listietoja tuotteen palauttamisesta on osoitteessa www.motorola.com/recycling/weee. Svenska: Fr kunder inom EU: Alla produkter som uppntt sin livslngd mste returneras till Motorola fr tervinning. Information om hur du returnerar produkten finns p www.motorola.com/recycling/weee. QRG_507.fm Page 36 Wednesday, January 28, 2009 8:37 PM Service Information If you have a problem using the equipment, contact your facilitys Technical or Systems Support. If there is a problem with the equipment, they will contact the Motorola Enterprise Mobility Support at:

www.motorola.com/enterprisemobility/support. For the latest version of this guide go to:

www.motorola.com/enterprisemobility/manuals. Motorola, Inc. One Motorola Plaza Holtsville, New York 11742, USA 1-800-927-9626 http://www.motorola.com MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their registered owners. Motorola, Inc. 2009

@72-115988-01@

72-115988-01 Revision A - January 2009