FEATURES 1 2 3 9 4 5 Post in Work Area Post in Work Area RFD2000 RFID Sled Quick Start Guide www.zebra.com/rfd2000 INTRODUCTION The RFD2000 sled provides Radio Frequency Identification
(RFID) tag reading, wrtiting, and locating capability to Zebras TC20 mobile computer. For detailed information, refer to the Product Reference Guide at: www.zebra.com/support. 8 7 6 1 LED Indicator (2) 2 Antenna 3 Battery Compartment 4 Battery Compartment Latch 5 Battery Compartment Screw 6 Lanyard Hook 7 Trigger 8 Retention Clip (2) 9 Connector for TC20 Lanyard See Product Reference Guide for detailed information BATTERY REPLACEMENT Note: For initial use, fully charge the RFD2000 RFID sled for X ??? hours. Remove the Battery 1. Remove the Battery Cap screw using a Phillips head screw driver. 2. Turn the Battery Latch counter clockwise approximately 30 using a flat head screw driver or coin. 3. Remove the Battery Cap. 4. Remove Battery. Inserting the Battery 1. Insert the battery, connector end first, contacts facing toward trigger, into the Battery Compartment. 2. Place the Battery Cap on. 3. Turn the Battery Latch clockwise using a flat head screw driver or coin. 4. Screw the Battery Cap screw using a Phillips head screw driver and tighten. Inserting the TC20 into the RFID Sled Place the TC20 fully forward on the RFD2000 sled base and push the TC20 down into the retention clips to secure the TC20 to the RFID Sled. Removing the TC20 from the RFID Sled To remove the TC20, firmly hold the RFD2000 sled handle, and lift the TC20 off of the sled base. DEVICE INSTALLATION GETTING STARTED Using the RFD2000 To use the RFD2000 for the first time with the TC20:
1. Charge the RFD2000 in the charging cradle. 2. Attach the TC20 on the RFD2000. 3. Set the region and power level (using the RFID Demo Application, RFID Manager Application, or the Partner Application). For the latest versions of guides and software, go to:
www.zebra.com/support. SOFTWARE Using RFID Manager for Android /RFID Demo Note: Zebra RFID Manager for Android must be installed before the RFID Demo application. To use the RFID Manager / Zebra RFID Demo for RFID operations:
1. Ensure that the RFID Manager for Android is installed on the TC20. The Zebra RFID Demo can be installed after RFID Manager is installed and verified. 2. Launch the application on the TC20. 3. Connect the RFD2000. 4. Before using the device for the first time, set the region in which the device is operating. To set the region, open the application and select Settings > Regulatory. 5. The application displays a successfully installed message. To manually verify the installation is successfully installed, select Setting > ???
Note: Zebra RFID Manager does not supply real time information or allow settings setup if the RFID Demo Application or Partner Application is connected to the RFD2000. Charging The RFD2000 RFID Sled and TC20 Mobile Computer may be charged in the charging cradle individually or attached together. Fully charge the RFD2000 by placing it in the charging cradle before first use. When an RFD2000 RFID Sled is removed from a charging cradle, it is automatically powered On. If a reader is not used for a duration of thirty minutes, the reader enters Off mode. Pressing the handle trigger for two seconds turns the reader back On. Single Slot Charging Cradle Five Slot Charging Cradle CHARGING OPTIMUM TAG DECODING RFID Operation LED INDICATORS Power LED Condition Battery Indication While Charging Pre-charging Charging Fully Charged Charging Error Battery Indication While Not Charging*
Battery Charge Status Green when remaining charge is 99%-51%
Amber when remaining charge is 21%-50%
Red when remaining charge is 0%-20%
Amber (Fast, Fast, Slow) Amber (Blinking) Green (Stays On) Amber (Fast Blinking)
*The battery charge status LED indicator appears within four seconds of removing the RFD2000 RFID Sled from the charging cradle. Draft 6 RFD2000 OPTIMUM BODY POSTURE Optimum Upright Body Posture Optimum Body Posture for Low Scanning Optimum Body Posture for High Scanning AVOID EXTREME WRIST ANGLES Use a ladder AVOID EXTREME WRIST ANGLES Taking breaks and task rotation recommended AVOID BENDING AVOID REACHING REGULATORY INFORMATION RF Exposure Guidelines Safety Information Reducing RF Exposure - Use Properly Only operate the device in accordance with instructions supplied. International The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. For information on International human exposure to electromagnetic fields, refer to the Zebra Declaration of Conformity (DoC) at www.zebra.com/doc. For further information on the safety of RF energy from wireless devices, see www.zebra.com/responsibility located under Corporate Responsibility. Europe - Handheld Devices To comply with EU RF exposure requirements, this device must be operated in the hand with a minimum separation distance of 20 cm or more from a persons body. Other operating configurations should be avoided. US This device was tested for typical hand held operation. The FCC has granted an Equipment Authorization for these model phones with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on these model phones is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/oet/ea/fccid. The use of third-party accessories may not ensure compliance with FCC RF exposure requirements, and should be avoided. Canada This device was tested for typical hand held operation. The ISED has approved these model phones with all reported SAR levels evaluated as in compliance with the ISED RF exposure guidelines. SAR information on these model phones is on file with the ISED and can be found under the SAR Results section of https://sms- sgs.ic.gc.ca/equipmentSearch/-
searchRadioEquipments. The use of third-party accessories may not ensure compliance with ISED RF exposure requirements, and should be avoided. Cet appareil a t test pour une opration manuelle typique. L'ISED a approuv ces modles de tlphones avec tous les niveaux SAR dclars valus conformment aux directives d'exposition RF ISED. L'information SAR sur ces modles de tlphones est en mmoire avec l'ISED et peut tre trouve dans la section Rsultats SAR de https://sms-
sgs.ic.gc.ca/equipmentSearch/searchRadioEquipements. L'utilisation d'accessoires tiers peut ne pas garantir la conformit aux exigences d'exposition RF ISED, et devrait tre vite. Radio Frequency Interference Requirements - FCC Tested to comply with FCC Standards FOR HOME OR OFFICE USE Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help. Radio Transmitters (Part 15) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. Radio Frequency Interference Requirements Canada CAN ICES-3 (B)/NMB-3 (B) Radio Transmitters This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio lectrique subi mme si le brouillage est susceptible d'en compromettre le fonctionnement. CE Marking and European Economic Area (EEA) Statement of Compliance Zebra hereby declares that this radio equipment is in compliance with Direc-
tives, 2014/53/EU and 2011/65/EU.The full text of the EU Declaration of Conformity is available at the following internet address: www.zebra.com/doc. Korea Warning Statement for Class B ITE B
( )
(B)
, . Brazil (UNWANTED EMISSIONS - ALL PRODUCTS) Declaraes Regulamentares para RFD2000 - Brazil Nota: A marca de certificao se aplica ao Transceptor, modelo RFD2000. Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio. Para maiores informaes sobre ANATEL consulte o site: www.anatel.gov.br. Este produto est homologado pela Anatel, de acordo com os procedimentos regulamentados pela Resoluo n242/2000 e atende aos requisitos tcnicos aplicados, incluindo os limites de exposio da Taxa de Absoro Especfica referente a campos eltricos, magnticos e eletromagnticos de radiofrequncia, de acordo com as Resolues n 303/2002 e 533/2009. Chile Este equipo cumple con la Resolucin No 403 de 2008, de la Subsecretaria de telecomunicaciones, relativa a radiaciones electromagnticas. China www.zebra.com/support
:
Eurasian Customs Union EAC . Taiwan Thailand
. Batteries Taiwan - Recycling EPA (Environmental Protection Administration) requires dry battery produc-
ing or importing firms in accordance with Article 15 of the Waste Disposal Act are required to indicate the recycling marks on the batteries used in sales, giveaway, or promotion. Contact a qualified Taiwanese recycler for proper battery disposal. Battery Information Caution: Risk of explosion if battery is replaced by an incorrect type. Dispose of batteries according to instructions. Use only Zebra approved batteries. Accessories which have battery charging capability are approved for use with the following battery models:
Part Number: BT-000341-01 and BT-000341-02; (3.6 Vdc, 3150 mAh). Zebra approved rechargeable battery packs are designed and constructed to the highest standards within the industry. However, there are limitations as to how long a battery can operate or be stored before needing replacement. Many factors affect the actual life cycle of a battery pack such as heat, cold, harsh environmental conditions, and severe drops. When batteries are stored over six months, some irreversible deterioration in overall battery quality may occur. Store batteries at half of full charge in a dry, cool place, removed from the equipment to prevent loss of capacity, rusting of metallic parts, and electrolyte leakage. When storing batteries for one year or longer, the charge level should be verified at least once a year and charged to half of full charge. Replace the battery when a significant loss of run time is detected. Standard warranty period for all Zebra batteries is one year, regardless if the battery was purchased separately or included as part of the mobile computer or bar code scanner. For more information on Zebra batteries, please visit:
www.zebra.com/batterybasics. Battery Safety Guidelines The area in which the units are charged should be clear of debris and combustible materials or chemicals. Particular care should be taken where the device is charged in a non-commercial environment. Follow battery usage, storage, and charging guidelines found in the user's guide. Improper battery use may result in a fire, explosion, or other hazard. To charge the mobile device battery, the battery and charger temperatures must be between +32 F and +104 F (0 C and +40 C). Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact Zebra support. Do not disassemble or open, crush, bend or deform, puncture, or shred. Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat. Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals. Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, or expose to fire, e explosion, or other hazard. Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer. Battery usage by children should be supervised. Please follow local regulations to promptly dispose of used re-chargeable batteries. Do not dispose of batteries in fire. Seek medical advice immediately if a battery has been swallowed. In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice. If you suspect damage to your equipment or battery, contact Zebra support to arrange for inspection. Warranty For the complete Zebra hardware product warranty statement, go to:
www.zebra.com/warranty. For Australia Only This warranty is given by Zebra Technologies Asia Pacific Pte. Ltd., 71 Robinson Road, #05-02/03, Singapore 068895, Singapore. Our goods come with guarantees that cannot be excluded under the Australia Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Zebra Technologies Corporation Australias limited warranty above is in addition to any rights and remedies you may have under the Australian Consumer Law. If you have any queries, please call Zebra Technologies Corporation at
+65 6858 0722. You may also visit our website: www.zebra.com for the most updated warranty terms. Service Information If you have a problem using the equipment, contact your facilitys Technical or Systems Support. If there is a problem with the equipment, they will contact Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return product, please go to: www.zebra.com/weee. Bulgarish: :
Zebra . ,
: www.zebra.com/weee. etina: Pro zkaznky z EU: Vechny produkty je nutn po skonen jejich ivotnosti vrtit spolenosti Zebra k recyklaci. Informace o zpsobu vrcen produktu najdete na webov strnce:
www.zebra.com/weee. Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, nr de er udtjent. Ls oplysningerne om returnering af produkter p: www.zebra.com/weee. Deutsch: Fr Kunden innerhalb der EU: Alle Produkte mssen am Ende ihrer Lebensdauer zum Recycling an Zebra zurckgesandt werden. Informationen zur Rcksendung von Produkten finden Sie unter www.zebra.com/weee.
: ..: , , Zebra .
, www.zebra.com/weee . Eesti: EL klientidele: kik tooted tuleb nende eluea lppedes tagastada taaskasutamise eesmrgil Zebra'ile. Lisainformatsiooni saamiseks toote tagastamise kohta klastage palun aadressi:
www.zebra.com/weee. Espaol: Para clientes en la Unin Europea: todos los productos debern entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si desea ms informacin sobre cmo devolver un producto, visite: www.zebra.com/weee. Franais : Clients de l'Union Europenne : Tous les produits en fin de cycle de vie doivent tre retourns Zebra pour recyclage. Pour de plus amples informations sur le retour de produits, consultez
: www.zebra.com/weee. Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni sulle modalit di restituzione, visitare il seguente sito Web: www.zebra.com/weee. Latvieu: ES klientiem: visi produkti pc to kalpoanas ma beigm ir jnogd atpaka Zebra otrreizjai prstrdei. Lai iegtu informciju par produktu nogdanu Zebra, ldzu, skatiet:
www.zebra.com/weee. Lietuvi: ES vartotojams: visi gaminiai, pasibaigus j eksploatacijos laikui, turi bti grinti utilizuoti kompanij Zebra. Daugiau informacijos, kaip grinti gamin, rasite: www.zebra.com/weee. Magyar: Az EU-ban vsrlknak: Minden tnkrement termket a Zebra vllalathoz kell eljuttatni jrahasznosts cljbl. A termk visszajuttatsnak mdjval kapcsolatos tudnivalkrt ltogasson el a www.zebra.com/weee weboldalra. Malti: Gal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aar tal-ajja ta' l-uu taghom, iridu jiu rritornati gand Zebra gar-riikla. Gal aktar tagrif dwar kif gandek tirritorna l-prodott, jekk jogbok ur: www.zebra.com/weee. Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg www.zebra.com/weee voor meer informatie over het terugzenden van producten. Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji naley zwrci do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktw znajduj si na stronie internetowej www.zebra.com/weee. Portugus: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos Zebra para reciclagem. Para obter informaes sobre como devolver o produto, visite: www.zebra.com/weee. Romnesc: Pentru clienii din UE: Toate produsele, la sfritul duratei lor de funcionare, trebuie returnate la Zebra pentru reciclare. Pentru informaii despre returnarea produsului, accesai:
www.zebra.com/weee. Slovenina: Pre zkaznkov z krajn EU: Vetky vrobky musia by po uplynut doby ich ivotnosti vrten spolonosti Zebra na recyklciu. Bliie informcie o vrten vrobkov njdete na:
www.zebra.com/weee. Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku ivljenjske dobe vrniti podjetju Zebra za reciklao. Za informacije o vrailu izdelka obiite: www.zebra.com/weee. Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrtettvksi Zebra-yhtin, kun tuotetta ei en kytet. Listietoja tuotteen palauttamisesta on osoitteessa www.zebra.com/weee. Svenska: Fr kunder inom EU: Alla produkter som uppntt sin livslngd mste returneras till Zebra fr tervinning. Information om hur du returnerar produkten finns p www.zebra.com/weee. Trke: AB Mterileri iin: Kullanm sresi dolan tm rnler geri dntrme iin Zebra'ya iade edilmelidir. rnlerin nasl iade edilecei hakknda bilgi iin ltfen u adresi ziyaret edin:
www.zebra.com/weee. TURKISH WEEE Statement of Compliance EEE Ynetmeliine Uygundur Recommended Usage Guide Zebra reserves the right to make changes to any product to improve reliability, function, or design. Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Zebra products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Zebra products. Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies company. This Zebra Product may include Zebra Software, Commercial Third Party Software, and Publicly Available software. Refer to Product Reference Guide for complete copyright, conditions and disclaimer information. Regulatory Information This device is approved under Zebra Technologies Corporation. This guide applies to the RFD2000. All Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Local language translations are available at the following website:
www.zebra.com/support. Any changes or modifications to Zebra equipment, not expressly approved by Zebra, could void the users authority to operate the equipment. Caution:
Only use Zebra approved and UL listed accessories, battery packs, and battery chargers. Do NOT attempt to charge damp/wet mobile computers or batteries. All components must be dry before connecting to an external power source. Declared maximum operating temperature: 50C. Wireless Device Country Approvals Note: this section is only applicable to WW/WR/EU configurations. Regulatory markings, subject to certification, are applied to the device signifying the radio(s) is/are approved for use in the following countries: United States, Canada, Japan, China, S. Korea, Australia, and Europe. Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at http://www.zebra.com/doc. Note: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Caution:
Operation of this device without regulatory approval is illegal. Health and Safety Recommendations Ergonomic Recommendations Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company's safety programs to prevent employee injury. Reduce or eliminate repetitive motion Maintain a natural position Reduce or eliminate excessive force Keep objects that are used frequently within easy reach Perform tasks at correct heights Reduce or eliminate vibration Reduce or eliminate direct pressure Provide adjustable workstations Provide adequate clearance Provide a suitable working environment Improve work procedures. Warnings for Use of Wireless Devices Caution:
Caution:
Caution:
Please observe all warning notices with regard to the usage of wireless Please observe all warning notices with regard to the usage of wireless Please observe all warning notices with regard to the usage of wireless devices. devices. devices. Potentially Hazardous Atmospheres - Vehicles Use You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants, etc., and areas where the air contains chemicals or particles such as grain, dust, or metal powders and any other area where you would normally be advised to turn off your vehicle engine. Safety in Aircraft Switch off your wireless device whenever you are instructed to do so by airport or airline staff. If your device offers a flight mode or similar feature, consult airline staff as to its use in flight. Safety in Hospitals Wireless devices transmit radio frequency energy and may affect medical electrical equipment. Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics, or healthcare facilitlies. These requests are designed to prevent possible interference with sensitive medical equipment. Pacemakers Pacemaker manufacturers recommended that a minimum of 15 cm (6 inches) be maintained between a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with independent research and recommendations by Wireless Technology Research. Persons with Pacemakers Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON. Should not carry the device in a breast pocket. Should use the ear furthest from the pacemaker to minimise the potential for interference. If you have any reason to suspect that interference is taking place, turn OFF your device. Other Medical Devices Please consult your physician or the manufacturer of the medical device to determine if the operation of your wireless product may interfere with the medical device. China RoHS This table was created to comply with China RoHS requirements. 35
(Parts)
(Pb)
(Hg)
(Cd)
(Cr (VI))
(PBB)
(PBDE)
(Metal Parts)
(Circuit Modules)
(Cables and Cable Assemblies)
(Plastic and Polymeric Parts)
(Optics and Optical Components)
(Batteries) O X O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O SJ/T 11364 O: SJ/T 11364--2014 X: SJ/T 11364--2014
(
This table was created to comply with China RoHS requirements. Lorem ipsum Zebra Technologies Corporation Lincolnshire, IL U.S.A. www.zebra.com 2017 ZIH Corp and/or its affiliates. All rights reserved. Zebra and the stylized Zebra head are trademarks of ZIH Corp, registered in many jurisdictions worldwide. All other trademarks are the property of their MN-003129-01 Revision A November 2017 RFD2000 Draft 6