rfd4031-rg-en-draft1.fm Page 1 RFD4031 Regulatory Guide Regulatory Information This device is approved under Zebra Technologies Corporation.This guide applies to the following model number: RFD4031 All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold and will be labeled as required. Local language translation / Traduo do idioma local / bersetzung in die lokale Sprache / Raduccion de idioma local / Traduction en langue locale / Prijevod na lokalni jezik / Traduzione in lingua locale /
/ / / / / Yerel dil eviri
/Tumaczenie na jzyk lokalny : zebra.com/support Any changes or modifications to Zebra equipment not expressly approved by Zebra could void the users authority to operate the equipment. Declared maximum operating temperature: 50C For use only with Zebra approved and UL Listed mobile devices, Zebra approved, and UL Listed/Recognized battery packs. Bluetooth Wireless Technology This is an approved Bluetooth product. For more information on the Bluetooth SIG listing, please visit bluetooth.com. Regulatory Markings Regulatory markings subject to certification are applied to the device signifying the radio(s) is/are approved for use. Refer to the Declaration of Conformity (DoC) for details of other country markings. The DOC is available at: zebra.com/doc. Health and Safety Recommendations Ergonomic Recommendations In order to avoid or minimize the potential risk of ergonomic injury, always follow good ergonomic workplace practices. Consult with your local Health and Safety Manager to ensure that you are adhering to your companys safety programs to prevent employee injury. Safety in Hospitals and Aircraft NOTE: Wireless devices transmit radio frequency energy that may affect medical electrical equipment and aircrafts operation. Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics, healthcare facilities or by airline staff. These requests are designed to prevent possible interference with sensitive equipments. Medical Devices It is recommended that a minimum separation distance of 20 cm (8 inches) be maintained between a wireless device and a medical devices such as pacemakers, defibrillator, or other implantable devices to avoid potential interference with the medical device. Pacemaker users should keep the device at the opposite side of the pacemaker or turn OFF the device if suspected of interference. ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corp., registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. 2020 Zebra Technologies Corp. and/or its affiliates. All rights reserved. | www.zebra.com rfd4031-rg-en-draft1.fm Page 2 Please consult your physician or the manufacturer of the medical device to determine if the operation of your wireless product may interfere with the medical device. RF Exposure Guidelines Safety Information Reducing RF Exposure Use Properly Only operate the device in accordance with the instructions supplied. The device complies with internationally recognized standards covering human exposure to electromagnetic fields. For information on international human exposure to electromagnetic fields, refer to the Zebra Declaration of Conformity (DoC) at zebra.com/doc. Use only Zebra tested and approved headset, belt-clips, holsters, and similar accessories to ensure RF exposure compliance. If applicable, follow the instructions for use as detailed in the accessory guide. The use of third-party belt clips, holsters, and similar accessories may not comply with RF exposure compliance requirements and should be avoided. For further information on the safety of RF energy from wireless devices, refer to RF exposure and assessment standards section at zebra.com/responsibility. To satisfy RF exposure requirements, this device must be hand-held only and, where applicable use only with Zebra tested and approved accessories. LED Devices Power Supply Classified as EXEMPT RISK GROUP according to IEC 62471:2006 and EN 62471:2008. Pulse Duration: 22.8 ms or CW (RFD4031 with SE4100) WARNING ELECTRICAL SHOCK: Use only a Zebra approved, Certified ITE LPS power supply with appropriate electrical ratings. Use of alternative power supply will invalidate any approvals given to this unit and may be dangerous. Batteries and Power Packs Battery Information This information applies to Zebra-approved batteries and power packs containing batteries. CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of batteries according to instructions. Use only Zebra approved batteries. Accessories which have battery charging capability are approved for use with the following battery models:
Model BT-000380 (3.6 VDC, 7000 mAh) Zebra approved rechargeable battery packs are designed and constructed to the highest standards within the industry. 2 rfd4031-rg-en-draft1.fm Page 3 However, there are limitations as to how long a battery can operate or be stored before needing replacement. Many factors affect the actual life cycle of a battery pack such as heat, cold, harsh environmental conditions, and severe drops. When batteries are stored over six months, some irreversible deterioration in overall battery quality may occur. Store batteries at half charge in a dry, cool place, removed from the equipment to prevent loss of capacity, rusting of metallic parts, and electrolyte leakage. When storing batteries for one year or longer, the charge level should be verified at least once a year and charged to half charge. Replace the battery when a significant loss of run time is detected. Standard warranty period for all Zebra batteries is one year, regardless if the battery was purchased separately or included as part of the host device. For more information on Zebra batteries, please visit:
zebra.com/batterydocumentation and select the Battery Best Practices link. Battery Safety Guidelines IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING When using this product basic safety precautions should always be followed, including the following:
The area in which the units are charged should be clear of debris and combustible materials or chemicals. Particular care should be taken where the device is charged in a non-commercial environment. Read all the instructions before using the product. Follow battery usage, storage, and charging guidelines found in the user's guide. Improper battery use may result in a fire, explosion, or other hazard. For devices that utilize a USB port as a charging source, the device shall only be connected to products that bear the USB-IF logo or have completed the USB-IF compliance program. Do not disassemble or open, crush, bend or deform, puncture, or shred. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury. Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat. Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals. Do not modify, disassemble, or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water, rain, snow or other liquids, or expose to fire, explosion, or other hazard. Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer. To reduce the risk of injury, close supervision is necessary when used near children. Please follow local regulations to promptly dispose of used re-chargeable batteries. Do not dispose of batteries in fire. Exposure to temperatures over 100C (212F) may cause explosion. Seek medical advice immediately if a battery has been swallowed. In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice. If you suspect damage to your equipment or battery, contact Zebra support to arrange for inspection. 3 rfd4031-rg-en-draft1.fm Page 4 Marking and European Economic Area (EEA) Statement of Compliance Zebra hereby declares that this radio equipment is in compliance with Directives 2014/53/EU and 2011/65/EU. Any radio operation limitations within EEA countries are identified in Appendix A of EU Declaration of Conformity. The full text of the EU Declaration of Conformity is available at: www.zebra.com/doc. EU Importer : Zebra Technologies B.V Address: Mercurius 12, 8448 GX Heerenveen, Netherlands Waste Electrical and Electronic Equipment (WEEE) For EU and UK Customers: For products at the end of their life, please refer to recycling/disposal advice at: zebra.com/weee. United States and Canada Regulatory Radio Frequency Interference Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Radio Frequency Interference Requirements Canada Innovation, Science and Economic Development Canada ICES-003 Compliance Label: CAN ICES-3
([B)/NMB-3(B) This device complies with Innovation, Science and Economic Development Canadas licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio lectrique subi mme si le brouillage est susceptible d'en compromettre le fonctionnement. 4 rfd4031-rg-en-draft1.fm Page 5 This device is restricted to indoor use when operating in the 5150 to 5350 MHz frequency range. Lorsqu'il fonctionne dans la plage de frquences 5 150- 5350 MHz, cet appareil doit tre utilis exclusivement en extrieur. RF Exposure Requirements - FCC and ISED The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated in compliance with the FCC RF emission guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of fcc.gov/oet/ea/fccid. To ensure compliance with FCC/ISED RF exposure requirement, the user shall keep the front of the RFID Device transmitting antenna at least 2.1 cm away from any nearby persons. Pour garantir la conformit aux exigences de la FCC/ISDE en matire dexposition aux RF, lutilisateur doit maintenir lavant de lantenne de transmission du dispositif RFID au moins 2.1 cm de toute personne proximit. Pour satisfaire aux exigences dexposition aux RF, cet appareil doit tre cheville utilis manuellement uniquement, le cas chant, uniquement utilis avec les accessoires approuvs et tests par Zebra. cm from the user or nearby persons. La conformit aux normes d'exposition RF tablies par les organismes FCC/ISED exige une distance minimale de xx cm entre l'antenne et l'utilisateur ou toute personne proximit lorsque celle-ci est installe l'extrieur ou lorsqu'elle est place sur un bureau ou dans une configuration similaire. zebra.com/support CCC ISM 5000 5 rfd4031-rg-en-draft1.fm Page 6
(Parts)
(Pb)
(Hg)
(Cd)
(Cr(VI))
(PBB)
(PBDE)
(Metal Parts)
(Circuit
(Cables
(Optics
(Print Heads)
(Batteries)
(Ext. Pwr Sply) SJ/T 11364 O: GB/T 26572 X: GB/T 26572 (
(EAC) EAC. France Singapore Paraguay Cet appareil a t test et dclar conforme aux limites applicables d'exposition aux radiofrquences (RF). Le dbit d'absorption spcifique (DAS) local quantifie l'exposition de l'utilisateur aux ondes lectromagntiques de l'quipement concern. Les valeurs DAS les plus leves sont disponibles sur la dclaration de conformit (DoC) disponible sur:
zebra.com/doc. End-users are required to obtain a site licence from the Infocomm Media Development Authority (IMDA) to operate RFID equipment in Singapore such as Zebra fixed and mobile RFID readers. For further information on this licensing requirement and the application process, end-users may contact IMDA (Tel:
6211 0647). En Paraguay este equipo deber ser configurado para operar con las limitaciones establecidas en la Norma Tcnica NTC-RF-918:2020 de la CONATEL. 6 rfd4031-rg-en-draft1.fm Page 7 Japan Mxico La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada.
/ 9 13
(EPA) 15 7 rfd4031-rg-en-draft1.fm Page 8 Unit
(Product Description in CHINESE Equipment name) Model Type designation (Type) Restricted substances and its chemical symbols
(Pb)
(Hg)
(Cd)
(Cr+6)
(PBB)
(PBDE) 1. 0.1 wt % 0.01 wt %
2. O 3. Note 1: Exceeding 0.1 wt% and exceeding 0.01 wt% indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition. Note 2: O indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence. Note 3: The indicates that the restricted substance corresponds to the exemption. TRK WEEE Uyumluluk Beyan EEE Ynetmeliine Uygundur. model1 x.xx w/kg model2 x.xx w/kg model3 x.xx w/kg
(Specific Absorption Rate SAR) 8 rfd4031-rg-en-draft1.fm Page 9 United Kingdom Statement of Compliance Zebra hereby declares that this radio equipment is in compliance with the Radio Equipment Regulations 2017 and the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. Any radio operation limitations within UK are identified in Appendix A of UK Declaration of Conformity. The full text of the UK Declaration of Conformity is available at: zebra.com/doc. UK Importer: Zebra Technologies Europe Limited Address: Dukes Meadow, Millboard Rd, Bourne End, Buckinghamshire, SL8 5XF Warranty Service Information Warranty Service Information For the complete Zebra hardware product warranty statement, go to: zebra.com\warranty. Before you use the unit, it must be configured to operate in your facility's network and run your applications. If you have a problem running your unit or using your equipment, contact your facility's Technical or System Support. If there is a problem with the equipment, they will contact Zebra support at zebra.com\support. For the latest version of the guide go to: zebra.com\support. For the complete Zebra hardware product warranty statement, go to: zebra.com\warranty. Before you use the unit, it must be configured to operate in your facility's network and run your applications. If you have a problem running your unit or using your equipment, contact your facility's Technical or System Support. If there is a problem with the equipment, they will contact Zebra support at zebra.com\support. For the latest version of the guide go to: zebra.com\support. Software Support Zebra wants to ensure that customers have the latest entitled software at the time of device purchase in order to keep the device operating at peak performance levels. To confirm that your Zebra device has the latest entitled software available at the time of purchase, visit zebra.com/support. Check for the latest software from Support > Products, or search for the device and select Support >
Software Downloads. 9 rfd4031-rg-en-draft1.fm Page 10 If your device does not have the latest entitled software as of your device purchase date, e-mail Zebra at entitlementservices@zebra.com and ensure you include the following essential device information:
Model number Serial number Proof of purchase Title of the software download you are requesting. If it is determined by Zebra that your device is entitled to the latest version of software, as of the date you purchased your device, you will receive an e-mail containing a link directing you to a Zebra Web site to download the appropriate software. Additional Information For information on using the RFD4031, refer to the RFD4031 product guide available at:
zebra.com/support. 10