FCC ID: UZ7ET65AW Rugged 2 in 1 Android Tablet

ET6x Rugged Enterprise Tablet Quick Start Guide MN-004748-01EN Rev A DRAFT Copyright 2023/05/23 ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. 2023 Zebra Technologies Corporation and/or its affiliates. All rights reserved. Information in this document is subject to change without notice. The software described in this document is furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in accordance with the terms of those agreements. For further information regarding legal and proprietary statements, please go to:

SOFTWARE: zebra.com/linkoslegal. COPYRIGHTS: zebra.com/copyright. PATENTS: ip.zebra.com. WARRANTY: zebra.com/warranty. END USER LICENSE AGREEMENT: zebra.com/eula. Terms of Use Proprietary Statement This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries

(Zebra Technologies). It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the express, written permission of Zebra Technologies. Product Improvements Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are subject to change without notice. Liability Disclaimer Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and disclaims liability resulting therefrom. Limitation of Liability In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation, consequential damages including loss of business profits, business interruption, or loss of business information) arising out of the use of, the results of use of, or inability to use such product, even if Zebra Technologies has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. DRAFT ET6x Quick Start Guide Features This section lists the features of the ET6x tablet. Figure 1ET6x Front View Table 1Front View 1 2 3 4 5 6 7 8 9 10 11 12 13 Number Item Description Front microphone Use for voice communications or audio recordings. Front camera Light sensor Access door Touch screen Use for video conferencing. Determines ambient light for controlling display backlight intensity. Secure door for accessing USB ports (two USB-A and one USB-C). Displays all information needed to operate the device. Pass-through antenna Use to connect to an external antenna. Speakers Charging indicator Provides audio output. Indicates power state and battery charging status while charging and application-generated notifications. Shoulder strap mount slots Provides mounting of shoulder straps clips. Power button Turns the display on and off. Press and release to power on the device. Press and hold to reset the device or power it off. Volume up button Increases the audio volume. Volume down button Decreases the audio volume. Keyboard interface connector Provides power and communication with the keyboard. 3 DRAFT ET6x Quick Start Guide Table 1Front View(Continued) Number Item Description P3 button Programmable button. Keyboard alignment slot Assists in aligning the tablet with the keyboard. P2 button P1 button Programmable button. Programmable button. 14 15 16 17 Figure 2USB Ports 2 1 Table 2USB Ports Number Item Description 1 2 USB-A port USB-C port Figure 3ET6x Back View Provides communication with accessories such as scanners. Provides communication with a host computer and charging using the USB-A to AC Adapter. 4 DRAFT ET6x Quick Start Guide Number Item Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 NFC antenna Stylus mount Use to read NFC cards. Provides mounting for a stylus tether. Accessory mount point locations Indicates mounting location points on polymer film for accessory captive screws. CAUTION: Do not remove the polymer film. scanner exit window Provides data capture using the imager. Rear camera Autofocus camera that takes photos. Front camera privacy cover switch Use to cover the front camera when not in use. Rear camera LED flash Provides illumination for the camera. Rear microphones Use for audio recordings. Communication expansion port For Ethernet and serial communication through the expansion adapter. Stylus mount Scan button Provides mounting for a stylus tether. Initiates barcode data capture when a scan-

enabled application is active. Dock alignment slot Assists in aligning the tablet with the dock. Dock locking mechanism Secures the tablet in a dock. Battery release latches Release the battery. Battery Provides power to the tablet. Setting Up the Device To start using the device for the first time:

1. 2. 3. Install a nano SIM card (optional for ET65 only). Install a microSD card. Install the battery. 4. Charge the device. Installing the nano SIM Card This section provides steps to install a nano SIM card. NOTE: Only use a nano SIM card. CAUTION: For proper electrostatic discharge (ESD) precautions to avoid damaging the SIM card. Proper ESD precautions include but are not limited to, working on an ESD mat and ensuring that the user is properly grounded. 5 DRAFT ET6x Quick Start Guide 1. Slide the battery release latches toward the sides of the tablet. The battery ejects slightly. 2. Lift the battery out of the tablet. 3. 4. Remove the access door. Slide the SIM card holder to the unlock position. 6 DRAFT ET6x Quick Start Guide 5. Lift the SIM card holder door. 6. Place the nano SIM card into the card holder with contacts facing down. 7. Close the SIM card holder door. 8. Slide to SIM card holder door to the lock position. NOTE:

9. Replace the access door. 7 DRAFT ET6x Quick Start Guide 10. Insert the battery, bottom first, into the battery compartment at the back of the device. 11. Press the battery down into the compartment until the release latches snap into place. Installing the microSD Card The microSD card slot provides secondary non-volatile storage. The slot is located under the battery. Refer to the documentation provided with the card for more information, and follow the manufacturers recommendations for use. CAUTION: Follow proper electrostatic discharge (ESD) precautions to avoid damaging the microSD card. Proper ESD precautions include but are not limited to, working on an ESD mat and ensuring that the operator is properly grounded. 1. Slide the battery release latches toward the sides of the tablet. The battery ejects slightly. 8 DRAFT ET6x Quick Start Guide 2. Lift the battery out of the tablet. 3. 4. Remove the access door. Slide the microSD card holder to the unlock position. 5. Lift the microSD card holder. 6. Insert the microSD card into the card holder door, ensuring that the card slides into the holding tabs on each side of the door. 9 DRAFT ET6x Quick Start Guide 7. Close the microSD card holder and lock it into position. NOTE: To ensure proper device sealing, the access door must be replaced and securely seated. 8. 9. Replace the access door. Insert the battery, bottom first, into the battery compartment at the back of the device. 10. Press the battery down into the compartment until the release latches snap into place. Installing the Battery This section describes how to install the battery into the tablet. NOTE: User modification of the device, particularly in the battery well, such as labels, asset tags, engravings, stickers, etc., may compromise the intended performance of the device or accessories. Performance levels such as sealing (Ingress Protection (IP)), impact performance

(drop and tumble), functionality, temperature resistance, etc. could be affected. DO NOT put any labels, asset tags, engravings, stickers, etc. in the battery well. 10 DRAFT ET6x Quick Start Guide 1. Insert the battery, bottom first, into the battery compartment at the back of the device. 2. Press the battery down into the compartment until the release latches snap into place. Device Charging Before using the tablet for the first time, connect it to an external power source. Keep the tablet connected to the external power source until fully charged. The Charging Indicator LED turns green when the tablet is fully charged. You may use the tablet while it is charging. To charge the main battery, connect the charging accessory to the appropriate power source. Insert the device into the dock or attach the USB charger. The device turns on and begins charging. The Charging/Notification LED blinks amber while charging, then turns solid green when fully charged. The battery charges from fully depleted to 90% in approximately 3.5 hours and from fully depleted to 100%

in approximately 4.5 hours. In many cases, the 90% charge provides plenty of charge for daily use. A full 100% charge lasts for approximately 14 hours of use. To achieve the best charging results, use only Zebra charging accessories and batteries. Charge batteries at room temperature with the device in sleep mode. Charging Accessories Use one of the following accessories to charge the tablet. Table 3Charging Accessories Accessory Part Number Description Vehicle Dock CRD-ET6X-VEHDK-CON-01 USB-C to AC Adapter PWR-BGA15V45W-UC2-WW Provides tablet charging only. Requires power supply (PWR-

BGA15V45W-UC2-WW) with country-specific AC line cord. Provides tablet charging only. Requires country-specific AC line cord. 11 DRAFT ET6x Quick Start Guide Charging Indicators Charge the tablet's battery before using the tablet. Table 4Charging Indicators LED Off Slow blinking orange

(1 blink every 4 seconds) Slow blinking red

(1 blink every 4 seconds) Indication The device is not in the cradle, not seated properly, or the cradle is not powered. The device is charging. The device is charging, but the battery is at the end of its useful life. Fast blinking orange Charging error. Possible charging errors include:

(2 blinks/second) Temperature is too low or too high. Fast blinking red

(2 blinks/second) Solid Green Solid Red Charging has gone on too long without completion (typically eight hours). Charging error and the battery is at the end of its useful life.Possible charging errors include:

Temperature is too low or too high. Charging has gone on too long without completion (typically eight hours). Charging complete. Charging is complete, but the battery is at the end of useful life. Charging Temperature Charge batteries in ambient temperatures. Charge batteries in temperatures from 5C to 40C (41F to 104F). The device always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37C (+98F)), the device may, for small periods of time, alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device indicates when charging is disabled due to abnormal temperatures via its LED. Vehicle Dock The vehicle dockprovides tablet charging, USB, Ethernet, and HDMI communication. NOTE: Ensure that you follow the guidelines for battery safety described in the ET6x Product Reference Guide. 12 DRAFT ET6x Quick Start Guide For detailed information on setting up the Vehicle Dock, see the ET6x Product Reference Guide. USB-C to AC Adapter The USB-C to AC Adapter provides power to the tablet. NOTE: Ensure that you follow the guidelines for battery safety described in the ET6x Product Reference Guide. 13 DRAFT ET6x Quick Start Guide Using the Camera Use the front or rear camera to take a photo or record a video. NOTE: If using the front camera, move the front camera privacy switch to the open position. To take a photo or record a video:

1. Open the Camera application. 2. Point the rear camera at an object. 14 DRAFT ET6x Quick Start Guide 3. Touch the on-screen shutter button to take a photo or record a video. Reading NFC Cards The tablet supports reading NFC cards. The NFC antenna is located on the back of the tablet under the NFC logo. With an NFC-enabled application open, bring the NFC card toward the antenna. Depending upon the application, an audio or visual indication indicates a successful reading of the card. Scanning with the Internal Scanner Use the internal imagerto capture barcode data. NOTE: To read a barcode, a scan-enabled app is required.The device contains the DataWedge app that allows the user to enable the scanner to decode barcode data and display the barcode content. 1. Ensure that an app is open on the device, and a text field is in focus (text cursor in the text field). 2. Point the exit window of the device at a barcode. 15 DRAFT ET6x Quick Start Guide 3. Press and hold the scan button. The aiming dot with illumination turns on to assist in aiming. 4. Ensure the barcode is within the area formed by the aiming pattern.The aiming dot is used for increased visibility in bright lighting conditions. to indicate the barcode was decoded successfully. Scanning with Camera Use the camera to capture barcode data. NOTE: To read a barcode, a scan-enabled app is required. The device contains the DataWedge app that allows the user to enable the scanner to decode barcode data and display the barcode content. 1. Ensure that an app is open on the device, and a text field is in focus (text cursor in the text field). 2. Point the camera window at a barcode. 16 DRAFT ET6x Quick Start Guide 3. Press and hold the scan button. By default, a preview window appears on the screen. 4. Move the device until the barcode is visible on the screen. 5. The Decode LED lights green, a beep sounds, and the device vibrates, by default, to indicate the barcode is decoded successfully. 6. The captured data appears in the text field. 17 DRAFT www.zebra.com DRAFT

ET6x Regulatory Guide Regulatory Information This device is approved under Zebra Technologies Corporation. This guide applies to the following model numbers:

ET60AW ET65AW All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold and will be labeled as required. Local language translation / (BG) / (CZ) Peklad do mstnho jazyka / (DE) bersetzung in die Landessprache / (EL) / (ES) Traduccin de idiomas locales / (ET) Kohaliku keele tlge / (FI) Paikallinen knns / (FR) Traduction en langue locale / (HR) Prijevod na lokalni jezik / (HU) Helyi nyelv fordts / (IT) Traduzione in lingua locale / (JA) /

(LT) Vietins kalbos vertimas / (LV) Tulkojums vietj valod / (NL) Vertaling in lokale taal / (PL) Tumaczenie na jzyk lokalny / (PT) Traduo do idioma local / (RO) Traducere n limba local / (RU)

/ (SK) Preklad do miestneho jazyka / (SL) Prevajanje v lokalni jezik / (SR)

/ (SV) versttning av lokalt sprk / (TR) Yerel dil evirisi / (ZH-CN)

/ (ZH-TW) / zebra.com/support Any changes or modifications to Zebra equipment not expressly approved by Zebra could void the users authority to operate the equipment. Declared maximum operating temperature: 60C CAUTION: Only use Zebra approved and NRTL-certified accessories, battery packs, and battery chargers. Do NOT attempt to charge damp/wet mobile computers, printers or batteries. All components must be dry before connecting to an external power source. Bluetooth Wireless Technology This is an approved Bluetooth product. For more information on the Bluetooth SIG listing, please visit bluetooth.com. Regulatory Markings Regulatory markings subject to certification are applied to the device signifying the radio(s) is/are approved for use. Refer to the Declaration of Conformity (DoC) for details of other country markings. The DOC is available at: zebra.com/doc. The regulatory marks specific to this device (including FCC and ISED) are available on the screen of the device by following these instructions:

Go to Settings > Regulatory. ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corp., registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. 2022 Zebra Technologies Corp. and/or its affiliates. All rights reserved. | zebra.com MN-004697-02EN DRAFT Health and Safety Recommendations Ergonomic Recommendations In order to avoid or minimize the potential risk of ergonomic injury, always follow good ergonomic workplace practices. Consult with your local Health and Safety Manager to ensure that you are adhering to your companys safety programs to prevent employee injury. Vehicle Installation RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles

(including safety systems). Check with the manufacturer or its representative regarding your vehicle. Ensure the equipment is installed to avoid driver distractions. You should also consult the manufacturer about any equipment that has been added to your vehicle. Position the device within easy reach. User should be able to access the device without removing their eyes from the road. IMPORTANT: Before installing or using, check national and local laws regarding distracted driving. Safety on the Road Give your full attention to driving. Obey the laws and regulations on the use of wireless devices in the areas where you drive. The wireless industry reminds you to use your device / phone safely when driving. Restricted Use Locations Remember to observe restrictions and obey all signs and instructions on the use of electronic devices in restricted use locations. Safety in Hospitals and Aircraft Wireless devices transmit radio frequency energy that may affect medical electrical equipment and aircrafts operation. Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics, healthcare facilities or by airline staff. These requests are designed to prevent possible interference with sensitive equipments. Medical Devices It is recommended that a minimum separation distance of 20 cm (8 inches) be maintained between a wireless device and a medical devices such as pacemakers, defibrillator, or other implantable devices to avoid potential interference with the medical device. Pacemaker users should keep the device at the opposite side of the pacemaker or turn OFF the device if suspected of interference. Please consult your physician or the manufacturer of the medical device to determine if the operation of your wireless product may interfere with the medical device. 2 DRAFT RF Exposure Guidelines Safety Information Reducing RF Exposure Use Properly Only operate the device in accordance with the instructions supplied. The device complies with internationally recognized standards covering human exposure to electromagnetic fields. For information on international human exposure to electromagnetic fields, refer to the Zebra Declaration of Conformity (DoC) at zebra.com/doc. Use only Zebra tested and approved headset, belt-clips, holsters, and similar accessories to ensure RF exposure compliance. If applicable, follow the instructions for use as detailed in the accessory guide. The use of third-party belt clips, holsters, and similar accessories may not comply with RF exposure compliance requirements and should be avoided. For further information on the safety of RF energy from wireless devices, refer to RF exposure and assessment standards section at zebra.com/responsibility. To satisfy RF exposure requirements, this device must operate with a minimum separation distance of cm or more from a user's body and nearby persons. 0 Optical Devices Laser Class 2 laser scanners use a low power, visible light diode. As with any very bright light source such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful. CAUTION: Use of controls, adjustments, or the performance of procedures other than those specified in the supplied product documentation may result in hazardous laser light exposure. SE5500 Wavelength: 500-750 nm Maximum output: 1 mW Pulse duration: 4 ms Beam divergence: 18 Repetition rate: 16.7 ms 3 DRAFT Scanner Labeling 1 2

Complies with 21CFR1040.10 & 1040.11 except for deviations pursuant to Laser Notice No. 56, dated May 8, 2019 and IEC/EN 60825-1:2014. Labels read:

1. Laser Light do not stare into beam. Class 2 Laser product. 500-570mm, 1mW (applied to SE5500) 2. Complies with 21 CFR1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 56, dated May 08, 2019 and IEC/EN 60825-1:2014. CAUTION: Laser light emitted from this aperture.

LED Risk Group classified according to IEC 62471:2006 and EN 62471:2008. SE5500 Pulse Duration: CW Exempt Group RG0 Power Supply WARNING ELECTRICAL SHOCK: Use only a Zebra approved, Certified ITE [LPS] power supply with appropriate electrical ratings. Use of alternative power supply will invalidate any approvals given to this unit and may be dangerous. Batteries and Power Packs This information applies to Zebra-approved batteries and power packs containing batteries. 4 DRAFT Battery Information CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of batteries according to instructions. Use only Zebra approved batteries. Accessories which have battery charging capability are approved for use with the following battery models:

Model BT-000471 (3.8 VDC, 8,920 mAh) Model BT-000471A (3.8 VDC, 18,720 mAh) Zebra approved rechargeable battery packs are designed and constructed to the highest standards within the industry. However, there are limitations as to how long a battery can operate or be stored before needing replacement. Many factors affect the actual life cycle of a battery pack such as heat, cold, harsh environmental conditions, and severe drops. When batteries are stored over six months, some irreversible deterioration in overall battery quality may occur. Store batteries at half charge in a dry, cool place, removed from the equipment to prevent loss of capacity, rusting of metallic parts, and electrolyte leakage. When storing batteries for one year or longer, the charge level should be verified at least once a year and charged to half charge. Replace the battery when a significant loss of run time is detected. Standard warranty period for all Zebra batteries is one year, regardless if the battery was purchased separately or included as part of the host device. For more information on Zebra batteries, please visit:

zebra.com/batterydocumentation and select the Battery Best Practices link. Battery Safety Guidelines IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING When using this product basic safety precautions should always be followed, including the following:

The area in which the units are charged should be clear of debris and combustible materials or chemicals. Particular care should be taken where the device is charged in a non-commercial environment. Read all the instructions before using the product. Follow battery usage, storage, and charging guidelines found in the user's guide. Batteries subjected to extremely low air pressure may result in an explosion or the leakage of Improper battery use may result in a fire, explosion, or other hazard. flammable liquid or gas. To charge the mobile device battery, the battery and charger temperatures must be between 0C and 40C (32F and 104F). Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact Zebra support. Do not disassemble or open, crush, bend or deform, puncture, or shred. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury. Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat. Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals. 5 DRAFT Do not modify, disassemble, or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water, rain, snow or other liquids, or expose to fire, explosion, or other hazard. Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer. To reduce the risk of injury, close supervision is necessary when used near children. Please follow local regulations to promptly dispose of used re-chargeable batteries. Do not dispose of batteries in fire. Exposure to temperatures over 100 C (212 F) may cause explosion. Seek medical advice immediately if a battery has been swallowed. In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice. If you suspect damage to your equipment or battery, contact Zebra support to arrange for inspection. Marking and European Economic Area (EEA) Statement of Compliance Zebra hereby declares that this radio equipment is in compliance with Directives 2014/53/EU and 2011/65/EU. Any radio operation limitations within EEA countries are identified in Appendix A of EU Declaration of Conformity. The full text of the EU Declaration of Conformity is available at: zebra.com/doc. EU Importer : Zebra Technologies B.V Address: Mercurius 12, 8448 GX Heerenveen, Netherlands Waste Electrical and Electronic Equipment (WEEE) For EU and UK Customers: For products at the end of their life, please refer to recycling/disposal advice at: zebra.com/weee. 6 DRAFT United States and Canada Regulatory Radio Frequency Interference Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Operation of transmitters in the 5.925 - 7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems. Increase the separation between the equipment and receiver. Radio Frequency Interference Requirements Canada This device complies with Innovation, Science and Economic Development Canadas licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio lectrique subi mme si le brouillage est susceptible d'en compromettre le fonctionnement. This device is restricted to indoor use when operating in the 5150 to 5350 MHz frequency range. Lorsqu'il fonctionne dans la plage de frquences 5 150- 5350 MHz, cet appareil doit tre utilis exclusivement en extrieur. Devices shall not be used for control of or communications with unmanned aircraft systems. Les dispositifs ne doivent pas tre utiliss pour commander des systmes daronef sans pilote ni pour communiquer avec de tels systmes. To satisfy RF exposure requirements, this device must operate with a minimum separation distance of 0 cm or more from a user's body and nearby persons. Pour satisfaire aux exigences d'exposition aux radio frquences, cet appareil doit fonctionner avec une distance de sparation minimale de 0 cm ou plus de corps d'une personne. Hotspot Mode To satisfy RF exposure requirements in hotspot mode, this device must operate with a minimum separation distance of 1.0 cm or more from a user's body and nearby persons. 7 DRAFT Pour satisfaire aux exigences d'exposition RF en mode hotspot, cet appareil doit fonctionner avec une distance de sparation minimale de 1,0 cm ou plus du corps de l'utilisateur et des personnes proximit. Devices shall not be used for control of or communications with unmanned aircraft systems. Les dispositifs ne doivent pas tre utiliss pour commander des systmes daronef sans pilote ni pour communiquer avec de tels systmes. Co-located Statement To comply with FCC RF exposure compliance requirement, the antenna used for this transmitter must not be co-located (within 20 cm) or operating in conjunction with any other transmitter/antenna except those already approved in this filling. Hotspot ISED Notice When operating in hotspot mode, this device is restricted to indoor use when operating in the 5150 - 5350 MHz frequency range. En mode de connexion partage (hotspot), l'utilisation de cet appareil doit se faire exclusivement en extrieur lorsqu'il fonctionne dans la plage de frquences 5 150 - 5 350 MHz. UL Listed Products with GPS Underwriters Laboratories Inc. (UL) has not tested the performance or reliability of the Global Positioning System (GPS) hardware, operating software, or other aspects of this product. UL has only tested for fire, shock, or casualties as outlined in ULs Standard(s) for Safety for Information Technology Equipment. UL Certification does not cover the performance or reliability of the GPS hardware and GPS operating software. UL makes no representations, warranties, or certifications whatsoever regarding the performance or reliability of any GPS related functions of this product. Marquage UL des produits quips d'un GPS Les tests mens par Underwriters Laboratories Inc. (UL) ne portent ni sur les performances, ni sur la fiabilit du matriel et du logiciel d'exploitation du GPS (Global Positioning System), ni sur tout autre aspect de ce produit. UL a uniquement test la rsistance au feu, aux chocs et aux sinistres, comme le dfinit la norme UL60950-1 relative la scurit des matriels de traitement de l'information. La certification UL ne couvre ni les performances, ni la fiabilit du matriel et du logiciel d'exploitation GPS. UL ne formule aucune dclaration, ni ne dlivre aucune garantie ni aucun certificat concernant les performances et la fiabilit des fonctions GPS de ce produit. Hazardous Locations Class 1 Div 2 Product Regulatory Information The following regulatory statements apply only to the Class 1 Div 2 products. The Class 1 Div 2 products are marked UL Listed 3JDT. Informations rglementaires sur les produits de classe 1, division 2 Les dclarations rglementaires suivantes ne s'appliquent qu'aux produits de classe 1, division 2. Les produits Class 1 Div 2 sont marqus UL Listed 3JDT 8 DRAFT (Japan)

(China) www.zebra.com/support

: www.tenaa.com.cn/.

SAR 2W/kg GB21288-2020 CCC ISM 5000 9 DRAFT

(Pb)

(Hg)

(Cd)

(Cr(VI))

(PBB)

(PBDE) X X O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O SJ/T 11364 O: GB/T 26572 X: GB/T 26572 (

Cet appareil a t test et dclar conforme aux limites applicables d'exposition aux radiofrquences (RF). Le dbit d'absorption spcifique (DAS) local quantifie l'exposition de l'utilisateur aux ondes lectromagntiques de l'quipement concern. Les valeurs SAR les plus leves sont disponibles sur la dclaration de conformit (DoC) disponible sur:

www.zebra.com/doc France Mxico La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. TRK WEEE Uyumluluk Beyan EEE Ynetmeliine Uygundur. 10 DRAFT United Kingdom Statement of Compliance Zebra hereby declares that this radio equipment is in compliance with the Radio Equipment Regulations 2017 and the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. Any radio operation limitations within UK are identified in Appendix A of UK Declaration of Conformity. The full text of the UK Declaration of Conformity is available at: zebra.com/doc. UK Importer: Zebra Technologies Europe Limited Address:

Dukes Meadow, Millboard Rd, Bourne End, Buckinghamshire, SL8 5XF 11 DRAFT Warranty For the complete Zebra hardware product warranty statement, go to: zebra.com\warranty. Service Information Before you use the unit, it must be configured to operate in your facility's network and run your applications. If you have a problem running your unit or using your equipment, contact your facility's Technical or System Support. If there is a problem with the equipment, they will contact Zebra support at zebra.com/support. For the latest version of the guide go to: zebra.com\support. Software Support Zebra wants to ensure that customers have the latest entitled software at the time of device purchase in order to keep the device operating at peak performance levels. To confirm that your Zebra device has the latest entitled software available at the time of purchase, go to zebra.com/support. Check for the latest software from Support > Products, or search for the device and select Support >

Software Downloads. If your device does not have the latest entitled software as of your device purchase date, e-mail Zebra at entitlementservices@zebra.com and ensure you include the following essential device information:

Model number Serial number Proof of purchase Title of the software download you are requesting. If it is determined by Zebra that your device is entitled to the latest version of software, as of the date you purchased your device, you will receive an e-mail containing a link directing you to a Zebra Web site to download the appropriate software. Product Support Information For information on using this product, see the User Guide at zebra.com/et60-info. To find quick answers to known product behaviors, access our knowledge articles at supportcommunity.zebra.com/s/knowledge-base. Ask your questions in our Support community at supportcommunity.zebra.com. Download product manuals, drivers, software, and view how-to videos at zebra.com/support. To request a repair for your product, go to zebra.com/repair. Patent Information To view Zebra patents, go to ip.zebra.com. 12 DRAFT

Regulatory Engineering Date: August 16, 2023 Attestation We, Zebra Technologies Corporation, attest the followings for our device FCC ID: UZ7ET65AW. a. this device will only associate and connect with a low-power indoor Access Point, subordinate device, or standard access point and never directly link to any other client devices b. this device will always initiate transmission under the control of a low power indoor AP or subordinate or standard client except access point for brief communications before joining a network. These quick messages will only occur if the client has detected an indoor AP, subordinate, or standard access point operating on a channel. These brief messages will have a time-out mechanism such that if it does not receive a response from an AP it will not continually repeat the request. c. this device, when associated and connected with a low-power indoor access point, subordinate or standard access point device, will operate at a power lower as advertised by the indoor access point, subordinate, or standard access point:

i. lower than or equal to the power advertised by the low-power indoor access point or subordinate and never above the maximum output power allowed by the FCC grant for clients associated with indoor clients or subordinates. ii. lower than or 6 dB below the power advertised by the standard access point. d. We acknowledging the device is prohibited for control of or communications with unmanned aircraft systems, including drones. Signature

Name and Job Title. E-mail Tel. _______________________________

: Larry (Qianlin) Zhou / Regulatory Specialist

: larry.zhou@zebra.com

: 346-260-3543 Zebra Technologies Corporation 1 Z e b r a P l a z a , | H o l t s v i l l e , N Y 11 7 4 2 | 1 . 6 3 1 . 7 3 8 . 2 4 0 0 p h o n e | 1 . 6 3 1 . 6 2 7 . 7 1 7 9 f a x | w w w. z e b r a . c o m