MN-004127-01ENa_tc26ek-rg-en.book Page 1 Wednesday, January 27, 2021 7:51 AM
TC26EK
Regulatory Guide
Regulatory Information
This device is approved under Zebra Technologies Corporation.
This guide applies to the following model number: TC26EK
All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold
and will be labeled as required.
Local language translation / Tradução do idioma local / Übersetzung in die lokale Sprache / Raduccion de
idioma local / Traduction en langue locale / Prijevod na lokalni jezik / Traduzione in lingua locale / 現地語
の翻訳 / 현지 언어 번역 / Перевод на местный язык / 本地語言翻譯 / 本地语言翻译 / Yerel dil çeviri
/Tłumaczenie na język lokalny : www.zebra.com/support
Any changes or modifications to Zebra equipment not expressly approved by Zebra could void the user’s
authority to operate the equipment.
Declared maximum operating temperature: 50°C
For use only with Zebra approved and UL Listed mobile devices, Zebra approved, and UL
Listed/Recognized battery packs.
Bluetooth® Wireless Technology
This is an approved Bluetooth® product. For more information on the Bluetooth SIG listing, please visit
www.bluetooth.com.
Regulatory Markings
Regulatory markings subject to certification are applied to the device signifying the radio(s) is/are approved
for use. Refer to the Declaration of Conformity (DoC) for details of other country markings. The DOC is
available at: www.zebra.com/doc.
The regulatory marks specific to this device (including FCC and ISED) are available on the screen of the
device by following these instructions:
Go to Settings > Regulatory.
Health and Safety Recommendations
Ergonomic Recommendations
In order to avoid or minimize the potential risk of ergonomic injury, always follow good ergonomic
workplace practices. Consult with your local Health and Safety Manager to ensure that you are adhering to
your company’s safety programs to prevent employee injury.
Vehicle Installation
RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles
(including safety systems). Check with the manufacturer or its representative regarding your vehicle.
Ensure the equipment is installed to avoid driver distractions. You should also consult the manufacturer
about any equipment that has been added to your vehicle.
Position the device within easy reach. User should be able to access the device without removing their
eyes from the road.
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corp., registered in many jurisdictions
worldwide. All other trademarks are the property of their respective owners. © 2020 Zebra Technologies Corp. and/or
its affiliates. All rights reserved. | www.zebra.com
MN-004127-01ENEN Rev. A
Draft v4 MN-004127-01ENa_tc26ek-rg-en.book Page 2 Wednesday, January 27, 2021 7:51 AM
TC26EK Regulatory Guide
IMPORTANT: Before installing or using, check national and local laws regarding distracted driving.
Safety on the Road
Give your full attention to driving. Obey the laws and regulations on the use of wireless devices in the
areas where you drive.
The wireless industry reminds you to use your device / phone safely when driving.
Restricted Use Locations
Safety in Hospitals and Aircraft
Remember to observe restrictions and obey all signs and instructions on the use of electronic devices in
restricted use locations.
NOTE: Wireless devices transmit radio frequency energy that may affect medical electrical
equipment and aircraft’s operation. Wireless devices should be switched off wherever you are
requested to do so in hospitals, clinics, healthcare facilities or by airline staff. These requests are
designed to prevent possible interference with sensitive equipments.
It is recommended that a minimum separation distance of 20 cm (8 inches) be maintained between a
wireless device and a medical devices such as pacemakers, defibrillator, or other implantable devices to
avoid potential interference with the medical device. Pacemaker users should keep the device at the
opposite side of the pacemaker or turn OFF the device if suspected of interference.
Please consult your physician or the manufacturer of the medical device to determine if the operation of
your wireless product may interfere with the medical device.
RF Exposure Guidelines
Safety Information
Reducing RF Exposure – Use Properly
Only operate the device in accordance with the instructions supplied.
The device complies with internationally recognized standards covering human exposure to
electromagnetic fields. For information on international human exposure to electromagnetic fields, refer to
the Zebra Declaration of Conformity (DoC) at www.zebra.com/doc.
Use only Zebra tested and approved headset, belt-clips, holsters, and similar accessories to ensure RF
exposure compliance. If applicable, follow the instructions for use as detailed in the accessory guide.
The use of third-party belt clips, holsters, and similar accessories may not comply with RF exposure
compliance requirements and should be avoided.
For further information on the safety of RF energy from wireless devices, refer to RF exposure and
assessment standards section at www.zebra.com/responsibility.
LED Devices
Classified as ‘EXEMPT RISK GROUP’ according to IEC 62471:2006 and EN 62471:2008.
Pulse Duration: CW ms (TC26EK with SE4710)
2
Draft v4 MN-004127-01ENa_tc26ek-rg-en.book Page 3 Wednesday, January 27, 2021 7:51 AM
TC26EK Regulatory Guide
Power Supply
Batteries and Power Packs
Battery Information
WARNING ELECTRICAL SHOCK: Use only a Zebra approved, Certified ITE [LPS] power supply
with appropriate electrical ratings. Use of alternative power supply will invalidate any approvals
given to this unit and may be dangerous.
This information applies to Zebra-approved batteries and power packs containing batteries.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of batteries
according to instructions.
Use only Zebra approved batteries. Accessories which have battery charging capability are
approved for use with the following battery models:
• Model BT-000409A (3.85 VDC, 3300 mAh)
Zebra approved rechargeable battery packs are designed and constructed to the highest standards within
the industry.
However, there are limitations as to how long a battery can operate or be stored before needing
replacement. Many factors affect the actual life cycle of a battery pack such as heat, cold, harsh
environmental conditions, and severe drops.
When batteries are stored over six months, some irreversible deterioration in overall battery quality may
occur. Store batteries at half charge in a dry, cool place, removed from the equipment to prevent loss of
capacity, rusting of metallic parts, and electrolyte leakage. When storing batteries for one year or longer,
the charge level should be verified at least once a year and charged to half charge.
Replace the battery when a significant loss of run time is detected.
• Standard warranty period for all Zebra batteries is one year, regardless if the battery was purchased
separately or included as part of the host device. For more information on Zebra batteries, please visit:
www.zebra.com/batterydocumentation and select the Battery Best Practices link.
Battery Safety Guidelines
IMPORTANT – SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS
WARNING – When using this product basic safety precautions should always be followed,
including the following:
The area in which the units are charged should be clear of debris and combustible materials or
chemicals. Particular care should be taken where the device is charged in a non-commercial environment.
• Read all the instructions before using the product.
• Follow battery usage, storage, and charging guidelines found in the user's guide.
•
Improper battery use may result in a fire, explosion, or other hazard.
To charge the mobile device battery, the battery and charger temperatures must be between
0°C and +40°C (+32°F and +104°F).
Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a
risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a
battery or a charger, contact Zebra support.
3
Draft v4 MN-004127-01ENa_tc26ek-rg-en.book Page 4 Wednesday, January 27, 2021 7:51 AM
TC26EK Regulatory Guide
For devices that utilize a USB port as a charging source, the device shall only be connected to products
that bear the USB-IF logo or have completed the USB-IF compliance program.
Do not disassemble or open, crush, bend or deform, puncture, or shred. Damaged or modified batteries
may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
Severe impact from dropping any battery-operated device on a hard surface could cause the battery to
overheat.
Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.
Do not modify, disassemble, or remanufacture, attempt to insert foreign objects into the battery, immerse
or expose to water, rain, snow or other liquids, or expose to fire, explosion, or other hazard.
Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or
near a radiator or other heat source. Do not place battery into a microwave oven or dryer.
To reduce the risk of injury, close supervision is necessary when used near children.
Please follow local regulations to promptly dispose of used re-chargeable batteries.
Do not dispose of batteries in fire. Exposure to temperatures over 100°C (212°F) may cause explosion.
Seek medical advice immediately if a battery has been swallowed.
In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has
been made, wash the affected area with large amounts of water and seek medical advice.
If you suspect damage to your equipment or battery, contact Zebra support to arrange for inspection.
Waste Electrical and Electronic Equipment (WEEE)
For EU Customers: For products at the end of their life, please refer to recycling/disposal advice at:
www.zebra.com/weee.
4
Draft v4 MN-004127-01ENa_tc26ek-rg-en.book Page 5 Wednesday, January 27, 2021 7:51 AM
TC26EK Regulatory Guide
United States and Canada Regulatory
Radio Frequency Interference Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable
protection against harmfulb interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Requirements - FCC and ISED
The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated in
compliance with the FCC RF emission guidelines. SAR information on this device is on file with the FCC
and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid.
To satisfy RF exposure requirements in hotspot mode, this device must operate with a minimum
separation distance of 1.0 cm or more from a user's body and nearby persons.
Hotspot Mode
Co-located Statement
To comply with FCC RF exposure compliance requirement, the antenna used for this transmitter must not
be co-located (within 20 cm) or operating in conjunction with any other transmitter/antenna except those
already approved in this filling.
Use with Hearing Aids - FCC
When some wireless devices are used near some hearing devices (hearing aids and cochlear implants),
users may detect a buzzing, humming, or whining noise. Some hearing devices are more immune than
others to this interference noise, and wireless devices also vary in the amount of interference they
generate. In the event of interference, you may want to consult your hearing aid supplier to discuss
solutions.
The wireless telephone industry has developed ratings for some of their mobile phones to assist hearing
device users in finding phones that may be compatible with their hearing devices. Not all phones have
been rated. Zebra terminals that are rated have the rating included on the Declaration of Conformity (DoC)
at www.zebra.com/doc.
5
Draft v4 MN-004127-01ENa_tc26ek-rg-en.book Page 6 Wednesday, January 27, 2021 7:51 AM
TC26EK Regulatory Guide
The ratings are not guarantees. Results will vary depending on the user’s hearing device and hearing loss.
If your hearing device happens to be vulnerable to interference, you may not be able to use a rated phone
successfully. Trying out the phone with your hearing device is the best way to evaluate it for your personal
needs.
ANSI C63.19 Rating System
In accordance with FCC hearing aid compatibility rules, certain phones be tested and rated under the
American National Standard Institute (ANSI) C63.19 hearing-aid compatibility standard. This standard
contains two types of ratings:
• M-Rating: For reduced radio-frequency interference to enable acoustic coupling with hearing aids that
don’t operate in telecoil mode
switch)
• T-rating : For inductive coupling with hearing aids operating in telecoil mode (t-switch or telephone
These ratings are on a scale from one to four, where four is the most compatible. A phone is considered
hearing-aid compatible under the FCC requirements if it's rated M3 or M4 for acoustic coupling and T3 or
T4 for inductive coupling.
Hearing devices may also be measured for immunity to this type of interference. Your hearing device
manufacturer or hearing health professional may help you find results for your hearing device. The more
immune your hearing aid is, the less likely you are to experience interference noise from mobile phones.
Hearing Aid Compatibility
This phone has been tested and rated for use with hearing aids for some of the wireless technologies that
it uses. However, there may be some newer wireless technologies used in this phone that have not been
tested yet for use with hearing aids. It is important to try the different features of this phone thoroughly and
in different locations using your hearing aid or cochlear implant to determine if you hear any interfering
noise. Consult your service provider or the manufacturer of this phone for information on hearing aid
compatibility. If you have questions about return or exchange policies, consult your service provider or
phone retailer.
This phone has been tested to ANSI C63.19 and rated for use with hearing aids; it received a M3/T4
rating. This device is marked HAC showing compliance with the applicable requirements of the FCC.
UL Listed Products with GPS
Underwriters Laboratories Inc. (UL) has not tested the performance or reliability of the Global Positioning
System (GPS) hardware, operating software, or other aspects of this product. UL has only tested for fire,
shock, or casualties as outlined in UL’s Standard(s) for Safety for Information Technology Equipment. UL
Certification does not cover the performance or reliability of the GPS hardware and GPS operating
software. UL makes no representations, warranties, or certifications whatsoever regarding the
performance or reliability of any GPS related functions of this product.
Marquage UL des produits équipés d'un GPS
Les tests menés par Underwriters Laboratories Inc. (UL) ne portent ni sur les performances, ni sur la
fiabilité du matériel et du logiciel d'exploitation du GPS (Global Positioning System), ni sur tout autre
aspect de ce produit. UL a uniquement testé la résistance au feu, aux chocs et aux sinistres, comme le
définit la norme UL60950-1 relative à la sécurité des matériels de traitement de l'information. La
certification UL ne couvre ni les performances, ni la fiabilité du matériel et du logiciel d'exploitation GPS.
UL ne formule aucune déclaration, ni ne délivre aucune garantie ni aucun certificat concernant les
performances et la fiabilité des fonctions GPS de ce produit.
6
Draft v4 MN-004127-01ENa_tc26ek-rg-en.book Page 7 Wednesday, January 27, 2021 7:51 AM
TC26EK Regulatory Guide
Warranty
Service Information
Software Support
For the complete Zebra hardware product warranty statement, go to: zebra.com\warranty.
Before you use the unit, it must be configured to operate in your facility's network and run your
applications.
If you have a problem running your unit or using your equipment, contact your facility's Technical or
System Support. If there is a problem with the equipment, they will contact Zebra support at
zebra.com\support.
For the latest version of the guide go to: zebra.com\support.
Zebra wants to ensure that customers have the latest entitled software at the time of device purchase in
order to keep the device operating at peak performance levels. To confirm that your Zebra device has the
latest entitled software available at the time of purchase, visit zebra.com\support.
Check for the latest software from Support > Products, or search for the device and select Support >
Software Downloads.
If your device does not have the latest entitled software as of your device purchase date, e-mail Zebra at
entitlementservices@zebra.com and ensure you include the following essential device information:
• Model number
• Serial number
• Proof of purchase
• Title of the software download you are requesting.
If it is determined by Zebra that your device is entitled to the latest version of software, as of the date you
purchased your device, you will receive an e-mail containing a link directing you to a Zebra Web site to
download the appropriate software.
Additional Information
For information on using the TC26EK, refer to the TC26EK product guide available at: zebra.com/support.
7
Draft v4