FCC ID: UZ7TC520L Touch Computer

TC52y/TC52y-HC Touch Computer Quick Reference Guide MN-004161-01EN Rev. A ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. 2021 Zebra Technologies Corporation and/or its affiliates. All rights reserved. Information in this document is subject to change without notice. The software described in this document is furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in accordance with the terms of those agreements. For further information regarding legal and proprietary statements, please go to:

SOFTWARE:zebra.com/linkoslegal COPYRIGHTS:zebra.com/copyright WARRANTY:zebra.com/warranty END USER LICENSE AGREEMENT: zebra.com/eula Terms of Use Proprietary Statement Product Improvements Liability Disclaimer Limitation of Liability Publication Date March 12, 2021 This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries

(Zebra Technologies). It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the express, written permission of Zebra Technologies. Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are subject to change without notice. Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and disclaims liability resulting therefrom. In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever

(including, without limitation, consequential damages including loss of business profits, business interruption, or loss of business information) arising out of the use of, the results of use of, or inability to use such product, even if Zebra Technologies has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. 2 Features CAUTION: The 8-pin interface connector at the bottom of the device is not removable. Trying to remove the connector will cause damage to the device and can void warranty. Figure 1 Front View 6 5 4 7 3 2 1 8 10 9 13 12 1 2 3 4 5 6 7 8 9 Number Item Function 5 MP Front Camera Takes photos and videos. Receiver Use for audio playback in Handset mode. Data Capture LED Indicates data capture status. Microphone Use for communications in Speakerphone mode. Proximity Sensor Light Sensor Determines proximity for turning off display when in handset mode. Determines ambient light for controlling display backlight intensity. Charging/Notification LED Indicates battery charging status while charging and application generated notifications. Touch Screen Displays all information needed to operate the device. Speaker 10 Interface Connector Provides audio output for video and music playback. Provides audio in speakerphone mode. Provides USB host and client communications, audio and device charging via cables and accessories. 11 3 Number Item Function 11 12 13 Microphone Scan Button Use for communications in Handset mode. Initiates data capture (programmable). Programmable Button Programmable button for use with applications. Figure 2 TC52y Rear View 1 2 3 13 12 11 10 1 2 3 4 5 6 7 8 9 10 11 12 13 3 4 5 9 8 6 7 Number Item Battery Function

>15.48 Watt hours (typical) / > 4,150 mAh PowerPrecision+

Lithium-ion battery. Basic Hand Strap Mount Provides mounting point for Basic Hand Strap accessory. Scan Button Initiates data capture (programmable). Battery Release Latches Press to remove the battery. Volume Up/Down Button Increase and decrease audio volume (programmable). 13 MP Rear Camera Takes photos and videos. Camera Flash Power Button Microphone Exit Window NFC Antenna Headset Jack Provides illumination for the camera. Turns the display on and off. Press and hold to reset the device, power off or swap battery. Use for noise cancellation. Provides data capture using the imager. Provides communication with other NFC-enabled devices. For audio output to headset. Trigger Handle Mount Provides electrical contacts and mounting for the Trigger Handle. 4 Figure 3 TC52y-HC Rear View 1 3 11 2 3 4 5 10 9 8 6 7 Number Item Function 1 2 3 4 5 6 7 8 9 10 11 Battery NFC Antenna Scan Button

>15.48 Watt hours (typical) / > 4,150 mAh PowerPrecision+

Lithium-ion battery. Provides communication with other NFC-enabled devices. Initiates data capture (programmable). Battery Release Latches Press to remove the battery. Volume Up/Down Button Increase and decrease audio volume (programmable). 13 MP Rear Camera Takes photos and videos. Camera Flash Power Button Microphone Exit Window Provides illumination for the camera. Turns the display on and off. Press and hold to reset the device, power off or swap battery. Use for noise cancellation. Provides data capture using the imager. Red Alert Button Programmable button for use with applications. Installing a microSD Card The microSD card slot provides secondary non-volatile storage. The slot is located under the battery pack. Refer to the documentation provided with the card for more information, and follow the manufacturers recommendations for use. CAUTION: Follow proper electrostatic discharge (ESD) precautions to avoid damaging the microSD card. Proper ESD precautions include, but are not limited to, working on an ESD mat and ensuring that the operator is properly grounded. 1. Lift the access door. 5 2. Slide the microSD card holder to the unlock position. 3. Lift the microSD card holder. 4. Insert the microSD card into the card holder door ensuring that the card slides into the holding tabs on each side of the door. 5. Close the microSD card holder and lock into position. CAUTION: Access door must be replaced and securely seated to ensure proper device sealing. 6. Re-install the access door. 6 Installing the Battery NOTE: User modification of the device, particularly in the battery well, such as labels, asset tags, engravings, stickers, etc., may compromise the intended performance of the device or accessories. Performance levels such as sealing (Ingress Protection (IP)), impact performance (drop and tumble), functionality, temperature resistance, etc. could be effected. Do not put any labels, asset tags, engravings, stickers, etc. in the battery well. To install the battery:

1. Insert the battery, bottom first, into the battery compartment in the back of the device. 2. Press the battery down until it snaps into place. 7 Charging the Device Use one of the following accessories to charge the device and/or spare battery. Table 1 Charging and Communication Description Part Number 1-Slot USB/Charge Only Cradle Kit CRD-TC51-1SCU-01 Yes Charging Communication Battery

(In Device) Spare Battery USB Yes No Ethernet With Optional Module CRD-TC5X-1SWS-01 Yes No Yes Yes 2-Slot USB/Ethernet Cradle CRD-TC5X-2SETH-01 CRD-TC51-5SCHG-01 1 -Slot Workstation Docking Cradle 5-Slot Charge Only Cradle Kit 4-Slot Charge Only Cradle with Battery Charger Kit 5-Slot Ethernet Cradle Kit CRD-TC51-5SETH-01 4-Slot Battery Charger Kit SAC-TC51-4SCHG-01 Rugged Charge/USB Cable CBL-TC51-USB1-01 Yes Yes Yes No Yes Yes No Yes No No Yes No No No Yes Yes No Yes No No CRD-TC51-5SC4B-01 Yes Yes No No Charging the Device NOTE: Ensure that you follow the guidelines for battery safety described in the TC52y Product Reference Guide. 1. To charge the main battery, connect the charging accessory to the appropriate power source. 2. Insert the device into a cradle or attach to a cable. The device turns on and begins charging. The Charging/Notification LED blinks amber while charging, then turns solid green when fully charged. The battery charges from fully depleted to 90% in approximately 2.5 hours and from fully depleted to 100%

in approximately three hours. In many cases the 90% charge provides plenty of charge for daily use. A full 100% charge lasts for approximately 14 hours of use. To achieve the best charging results use only Zebra charging accessories and batteries. Charge batteries at room temperature with the device in sleep mode. Charging the Spare Battery 1. Insert a spare battery into the spare battery slot. 2. Ensure the battery is seated properly. The Spare Battery Charging LED blinks indicating charging. See Table 2 for charging indicators. The battery charges from fully depleted to 90% in approximately 2.3 hours and from fully depleted to 100%

in approximately three hours. In many cases the 90% charge provides plenty of charge for daily use. A full 100% charge lasts for approximately 14 hours of use. To achieve the best charging results use only Zebra charging accessories and batteries. 8 Table 2 Charging/Notification LED Charging Indicators State LED Indication Off Slow Blinking Amber (1 blink every 4 seconds) Slow Blinking Red (1 blink every 4 seconds) Solid Green Solid Red Device is not charging. Device is not inserted correctly in the cradle or connected to a power source. Charger/cradle is not powered. Device is charging. Device is charging but the battery is at end of useful life. Charging complete. Charging complete but the battery is at end of useful life. Fast Blinking Amber (2 blinks/second) Charging error, e.g.:

Temperature is too low or too high. Fast Blinking Red (2 blinks/second) Charging has gone on too long without completion (typically eight hours). Charging error but the battery is at end of useful life., e.g.:

Temperature is too low or too high. Charging has gone on too long without completion (typically eight hours). Charge batteries in temperatures from 5C to 40C (41F to 104F). The device or cradle always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37C

(+98F)) the device or cradle may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device and cradle indicates when charging is disabled due to abnormal temperatures via its LED. 9 1-Slot USB Charging Cradle Item Name Description 1 Power LED Indicates that power is applied to the cradle. 1 10 1-Slot Workstation Docking Cradle 1 2 3 4 8 7 6 5 Item Name Description Power Port HDMI Port Ethernet Port LED Provides power to the cradle. Connects to monitor. Connects to an Ethernet network. Indicates that power is applied to the cradle. USB Type A Port Connection for mouse or keyboard. USB Type A Port Connection for mouse or keyboard. 1.5 mA USB Port USB Type A port for mouse or keyboard, or personal mobile device. 0.5 mA USB Port USB Type A port for mouse or keyboard. 1 2 3 4 5 6 7 8 11 2-Slot USB/Ethernet Cradle 1 3 2 Item Name Description 1 2 3 Device Charging Slot Holds the device during charging. Spare Battery Charge LED Indicates spare battery charge status. Spare Battery Slot Holds the spare battery during charging. 12 5-Slot Charge Only Cradle 1 2 Item Name Description Device Charging Slot Holds the device during charging. Power LED Indicates that power is applied to the cradle. 1 2 13 4-Slot Charge Only Cradle with Battery Charger 4 1 2 3 iTEM Name Description 1 2 3 4 Device Charging Slot Holds the device during charging. Spare Battery Slot Holds a spare battery during charging. Power LED Indicates that power is applied to the cradle. Spare Battery Charging LED Indicates spare battery charge status. 14 5-Slot Ethernet Cradle Item Name Description 1 2 3 Device Charging Slot Holds the device during charging and communication. 1000 LED 10/100 LED Indicates data rate of 1 Gbps when on or blinking. Indicates data rate of 10 or 100 Mbps when on or blinking. 1 2 3 15 4-Slot Battery Charger 3 1 2 Item Name Description 1 2 3 Spare Battery Slot Holds the spare battery during charging. Power LED Indicates that power is applied to the cradle. Spare Battery Charging LEDs Indicates spare battery charge status. 16 Rugged Charge/USB Cable 17 Scanning To read a barcode, a scan-enabled application is required. The device contains the DataWedge application that allows the user to enable the imager, decode the barcode data and display the barcode content. 1. Ensure that an application is open on the device and a text field is in focus (text cursor in text field). 2. Point the exit window on the top of the device at a barcode. 3. Press and hold the scan button. On the TC52y, the red LED aiming pattern and red aiming dot turns on to assist in aiming. On the TC52y-HC, the white LED aiming pattern and green aiming dot turns on to assist in aiming. NOTE: When the device is in Picklist mode, the imager does not decode the barcode until the crosshair or aiming dot touches the barcode. 4. Ensure the barcode is within the area formed by the cross-hairs in the aiming pattern. The aiming dot is used for increased visibility in bright lighting conditions. Aiming Pattern 18 Pick List Mode with Multiple Barcodes in Aiming Pattern 5. The Data Capture LED lights green and a beep sounds, by default, to indicate the barcode was decoded successfully. 6. Release the scan button. NOTE: Imager decoding usually occurs instantaneously. The device repeats the steps required to take a digital picture (image) of a poor or difficult barcode as long as the scan button remains pressed. 7. The barcode content data displays in the text field. 19 Ergonomic Considerations AVOID EXTREME WRIST ANGLES 20 www.zebra.com

MN-004164-01EN-Pa_tc52ax-rg-en.fm Page 11 TC520L Regulatory Guide Zebra Technologies |

3 Overlook Point |

Lincolnshire, IL 60069 USA zebra.com ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corp., registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. 2020 Zebra Technologies Corp. and/or its affiliates. All rights reserved. Regulatory Information This device is approved under Zebra Technologies Corporation. This guide applies to the following model number: TC520L All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold and will be labeled as required. Local language translation / Traduo do idioma local / bersetzung in die lokale Sprache / Raduccion de idioma local / Traduction en langue locale / Prijevod na lokalni jezik / Traduzione in lingua locale

/ / Yerel dil eviri /Tumaczenie na jzyk lokalny : zebra.com/support Any changes or modifications to Zebra equipment not expressly approved by Zebra could void the users authority to operate the equipment. Declared maximum operating temperature: 50C For use only with Zebra approved and UL Listed mobile devices, Zebra approved, and UL Listed/Recognized battery packs. CAUTION: Only use Zebra approved and NRTL-certified accessories, battery packs, and battery chargers. Do NOT attempt to charge damp/wet mobile computers, printers or batteries. All components must be dry before connecting to an external power source. Bluetooth Wireless Technology This is an approved Bluetooth product. For more information on the Bluetooth SIG listing, please visit www.bluetooth.com. Regulatory Markings Regulatory markings subject to certification are applied to the device signifying the radio(s) is/are approved for use. Refer to the Declaration of Conformity (DoC) for details of other country markings. The DOC is available at: zebra.com/doc. The regulatory marks specific to this device (including FCC and ISED) are available on the screen of the device by following these instructions:

Go to Settings > Regulatory. MN-004146-01EN-P May 5, 2021 Restricted Use Locations Remember to observe restrictions and obey all signs and instructions on the use of electronic devices in restricted use locations. Health and Safety Recommendations Ergonomic Recommendations In order to avoid or minimize the potential risk of ergonomic injury, always follow good ergonomic workplace practices. Consult with your local Health and Safety Manager to ensure that you are adhering to your companys safety programs to prevent employee injury.Vehicle Installation RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles (including safety systems). Check with the manufacturer or its representative regarding your vehicle. Ensure the equipment is installed to avoid driver distractions. You should also consult the manufacturer about any equipment that has been added to your vehicle. Position the device within easy reach. User should be able to access the device without removing their eyes from the road. IMPORTANT: Before installing or using, check national and local laws regarding distracted driving. Safety on the Road Give your full attention to driving. Obey the laws and regulations on the use of wireless devices in the areas where you drive. The wireless industry reminds you to use your device / phone safely when driving. Safety in Hospitals and Aircraft NOTE: Wireless devices transmit radio frequency energy that may affect medical electrical equipment and aircrafts operation. Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics, healthcare facilities or by airline staff. These requests are designed to prevent possible interference with sensitive equipments. Medical Devices RF Exposure Guidelines Safety Information Reducing RF Exposure Use Properly Only operate the device in accordance with the instructions supplied. The device complies with internationally recognized standards covering human exposure to electromagnetic fields. For information on international human exposure to electromagnetic fields, refer to the Zebra Declaration of Conformity (DoC) at zebra.com/doc. Use only Zebra tested and approved headset, belt-clips, holsters, and similar accessories to ensure RF exposure compliance. If applicable, follow the instructions for use as detailed in the accessory guide. The use of third-party belt clips, holsters, and similar accessories may not comply with RF exposure compliance requirements and should be avoided. For further information on the safety of RF energy from wireless devices, refer to RF exposure and assessment standards section at zebra.com/responsibility. Handheld or Body-Worn Devices To satisfy RF exposure requirements, this device must operate with a minimum separation distance of 1.5 cm or more from a user's body and nearby persons. Limb-worn Devices To satisfy RF exposure requirements, this device must be hand-use, only and, where applicable use only with Zebra tested and approved accessories. Laser Devices Class 1 Laser devices are not considered to be hazardous when used for their intended purpose. Figure 1 Laser Warning Label Class 1 Class 2 laser scanners use a low power, visible light diode. As with any very bright light source such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful. CAUTION: Use of controls, adjustments, or the performance of procedures other than those specified in the supplied product documentation may result in hazardous laser light exposure. Scanner Labeling COMPLIES WITH 21 CFR1040.10 AND 1040.11 EXCEPT FOR DEVIATIONS PURSUANT TO LASER NOTICE NO. 56, DATED May 08, 2019 AND IEC/EN 60825-1:2014. Labels read as follows - needs translation into additional languages. Labels read:

Laser Light do not stare into beam Class 2 Laser product. 630-680mm, 1mW Caution Class 3R laser light when open. Avoid direct eye exposure. Complies with 21 CFR1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 56, DATED May 08, 2019 and IEC/EN 60825-1:2014. LED Devices Classified as EXEMPT RISK GROUP according to IEC 62471:2006 and EN 62471:2008. Pulse Duration: TBD ms or CW (SE5500) Power Supply WARNING ELECTRICAL SHOCK: Use only a Zebra approved, Certified ITE SELV power supply with appropriate electrical ratings. Use of alternative power supply will invalidate any approvals given to this unit and may be dangerous. Batteries and Power Packs This information applies to Zebra-approved batteries and power packs containing batteries. Battery Information CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of batteries according to instructions. Use only Zebra approved batteries. Accessories which have battery charging capability are approved Model BT-000314 (3.6 VDC, 4300 mAh) Model BT-000314A (3.85 VDC, 3840 mAh) Model BT-000443 (3.6 VDC, 4300 mAh) for use with the following battery models:

Zebra approved rechargeable battery packs are designed and constructed to the highest standards within the industry. However, there are limitations as to how long a battery can operate or be stored before needing replacement. Many factors affect the actual life cycle of a battery pack such as heat, cold, harsh environmental conditions, and severe drops. When batteries are stored over six months, some irreversible deterioration in overall battery quality may occur. Store batteries at half charge in a dry, cool place, removed from the equipment to prevent loss of capacity, rusting of metallic parts, and electrolyte leakage. When storing batteries for one year or longer, the charge level should be verified at least once a year and charged to half charge. Replace the battery when a significant loss of run time is detected. Standard warranty period for all Zebra batteries is one year, regardless if the battery was purchased separately or included as part of the host device. For more information on Zebra batteries, please visit:

zebra.com/batterydocumentation and select the Battery Best Practices link. Battery Safety Guidelines IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING When using this product basic safety precautions should always be followed, including the following:

The area in which the units are charged should be clear of debris and combustible materials or chemicals. Particular care should be taken where the device is charged in a non-commercial environment. Read all the instructions before using the product. Follow battery usage, storage, and charging guidelines found in the user's guide. Improper battery use may result in a fire, explosion, or other hazard. To charge the mobile device battery, the battery and charger temperatures must be between 0C and +40C (+32F and +104F). Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact Zebra support. Marking and European Economic Area

(EEA) Statement of Compliance Zebra hereby declares that this radio equipment is in compliance with Directives 2014/53/EU and 2011/65/EU. Any radio operation limitations within EEA countries are identified in Appendix A of EU Declaration of Conformity. The full text of the EU Declaration of Conformity is available at: www.zebra.com/doc. EU Importer: Zebra Technologies B.V Address: Mercurius 12, 8448 GX Heerenveen, Netherlands Waste Electrical and Electronic Equipment (WEEE) For EU and UK Customers: For products at the end of their life, please refer to recycling/disposal advice at: zebra.com/weee. United States and Canada Regulatory Radio Frequency Interference Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Radio Frequency Interference Requirements Canada Innovation, Science and Economic Development Canada ICES-003 Compliance Label: CAN ICES-3 (B)/NMB-3(B) This device complies with Innovation, Science and Economic Development Canadas licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio lectrique subi mme si le brouillage est susceptible d'en compromettre le fonctionnement. This device is restricted to indoor use when operating in the 5150 to 5350 MHz frequency range. Lorsqu'il fonctionne dans la plage de frquences 5 150- 5350 MHz, cet appareil doit tre utilis exclusivement en extrieur. RF Exposure Requirements - FCC and ISED

(Specific Absorption Rate SAR) TC520L, 0.566 w/kg United Kingdom Statement of Compliance Zebra hereby declares that this radio equipment is in compliance with the Radio Equipment Regulations 2017 and the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. Any radio operation limitations within UK are identified in Appendix A of UK Declaration of Conformity. The full text of the UK Declaration of Conformity is available at:

zebra.com/doc. UK Importer: Zebra Technologies Europe Limited Address:

Dukes Meadow, Millboard Rd, Bourne End, Buckinghamshire, SL8 5XF Warranty For the complete Zebra hardware product warranty statement, go to: zebra.com\warranty. Service Information Before you use the unit, it must be configured to operate in your facility's network and run your applications. If you have a problem running your unit or using your equipment, contact your facility's Technical or System Support. If there is a problem with the equipment, they will contact Zebra support at zebra.com\support. For the latest version of the guide go to: zebra.com\support. Additional Information For information on using the TC520L, refer to the TC520L product guide available at: zebra.com/vanityURL. MN-004164-01EN-Pa_tc52ax-rg-en.fm Page 12 The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated in compliance with the FCC RF emission guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of fcc.gov/oet/ea/fccid. Handheld Devices To satisfy RF exposure requirements, this device must operate with a minimum separation distance of 1.5 cm or more from a user's body and nearby persons. Pour satisfaire aux exigences dexposition aux RF, cet appareil doit fonctionner une distance minimale de sparation de 1.5 cm ou plus du corps de lutilisateur et des personnes proximit. Pour satisfaire aux exigences dexposition aux RF, cet appareil doit tre lcheville utilis manuellement uniquement, le cas chant, uniquement utilis avec les accessoires approuvs et tests par Zebra. Co-located Statement To comply with FCC RF exposure compliance requirement, the antenna used for this transmitter must not be co-located (within 20 cm) or operating in conjunction with any other transmitter/antenna except those already approved in this filling. This device is marked HAC showing compliance with the applicable requirements of FCC Part 68 and ISED CS-03-Part 5. Brasil Este equipamento no tem direito proteo contra interferncia prejudicial e no pode causar interferncia em sistemas devidamente autorizados. Este produto est homologado pela Anatel de acordo com os procedimentos regulamentados para avaliao da conformidade de produtos para telecomunicaes e atende aos requisitos tcnicos aplicados, incluindo os liYDmites de exposio da Taxa de Absoro Especfica referente a campos eltricos, magnticos e eletromagnticos de radiofrequncia. Valores de SAR medidos:

Este dispositivo est em conformidade com as diretrizes de exposio a radiofrequncia quando posicionado pelo menos xxxx cm do corpo. Cabea: xxxx W/kg Corpo: xxxx W/kg zebra.com/support

CCC ISM 5000

(Pb)

(Hg)

(Cd)

(Cr(

VI))

(PB B)

(PB DE)

(Parts) SJ/T 11364 O: GB/T 26572 X:

GB/T 26572 (

Colombia Seor usuario, la siguiente informacin se entrega de conformidad con lo establecido en el Rgimen de proteccin de los derechos de los usuarios, expedido por la Comisin de Regulacin de Comunicaciones. Recomendaciones de uso:

Utilice siempre que pueda dispositivos manos libres. Evite utilizar el equipo mientras conduce un vehculo. En caso que el telfono sea utilizado por nios, ancianos, mujeres embarazadas y poblacin inmunocomprometida, consulte a su mdico y el manual del equipo. Si usted utiliza algn dispositivo electrnico de uso mdico, asegrese que el mismo est protegido contra las ondas de radiofrecuencia externas. Apague su telfono en lugares tales como: hospitales, centros de salud, aviones, estaciones de suministro de combustible, en presencia de gases explosivos y lugares donde se realizan explosiones. Evite que terceros hagan uso de su telfono para prevenir la implantacin de dispositivos como programas espas (spyware) o identificadores ocultos, que atentan contra la seguridad de la informacin contenida en el mismo.

(EAC) EAC. France Cet appareil a t test et dclar conforme aux limites applicables d'exposition aux radiofrquences (RF). Le dbit d'absorption spcifique (DAS) local quantifie l'exposition de l'utilisateur aux ondes lectromagntiques de l'quipement concern. Les valeurs DAS les plus leves sont disponibles sur la dclaration de conformit (DoC) disponible sur: zebra.com/doc. India The sending and receiving of texts is supported in the following Indian languages:

Assamese, Bengali, Gujarati, Hindi, Kannada, Kashmiri, Konkani, Malayalam, Manipuri, Marathi, Nepali, Oriya, Punjabi, Sanskrit, Sindhi, Tamil, Telugu, Urdu, Bodo, Santhali, Maithili, and Dogri. Mxico La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada.

: TC520L

: xxxx W/kg

(SAR : Specified Absorption Rate) 2 W/kg 1.6 W/kg

(rra.go.kr)

SAR

www.rra.go.kr

1 2

SAR

www.rra.go.kr

xxxx mm

/ 9 13

(EPA) 15

(Product Description in CHINESE Equipment name) TC520L Restricted substances and its chemical symbols Unit

(Pb)

(Hg)

(Cd)

(Cr+

6)

(PB B)

(PBD E) 1. 0.1 wt % 0.01 wt %

2. O 3. Note 1: Exceeding 0.1 wt% and exceeding 0.01 wt% indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition. Note 2: O indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence. Note 3: The indicates that the restricted substance corresponds to the exemption. Trkiye Bu cihaz Trke karakterlerin tamamn ihtiva eden ETSI TS 123.038 V8.0.0 (veya sonraki srmnkodu) ve ETSI TS 123.040 V8.1.0 (veya sonraki srmn kodu) teknik zelliklerine uygundur. TRK WEEE Uyumluluk Beyan EEE Ynetmeliine Uygundur.

Regulatory Engineering Date: May 5, 2021 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: FCC ID: UZ7TC520L AUTHORIZATION LETTER We, the undersigned, hereby authorize Jones Tsai in Sporton International Inc. to act on our behalf in all manners relating to FCC application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Jones Tsai in Sporton International Inc. on our behalf shall have the same effect as acts of our own. If you have any acknowledgement and response, please send it to Sporton International Inc. directly. Confidentiality Request Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely. Block Diagram Part List Operational Description Tune-up Procedure Schematic Diagram Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission s policy, in order to comply with the marketing regulations in 47 CFT 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachment(s) for 180 days after the grant as outlined in Public Notice DA 04-1705. External Photos Internal Photos Zebra Technologies Corporation 1 Z e b r a P l a z a , | H o l t s v i l l e , N Y 1 1 7 4 2 | 1 . 6 3 1 . 7 3 8 . 2 4 0 0 p h o n e | 1 . 6 3 1 . 6 2 7 . 7 1 7 9 f a x | w w w . z e b r a . c o m Regulatory Engineering Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Label Location Attestation We attest that the label of device FCC ID: UZ7TC520L is located in the battery room. The label is visible to the users as they purchase the product and install the battery. Sincerely, Signature

_______________________________ Name and Job Title. E-mail Tel.

: Larry (Qianlin) Zhou / Regulatory Specialist

: larry.zhou@zebra.com

: 346-260-3543 Zebra Technologies Corporation 1 Z e b r a P l a z a , | H o l t s v i l l e , N Y 1 1 7 4 2 | 1 . 6 3 1 . 7 3 8 . 2 4 0 0 p h o n e | 1 . 6 3 1 . 6 2 7 . 7 1 7 9 f a x | w w w . z e b r a . c o m