FCC ID: 2ADTD-K1109EKFBQR Card Reader

DS-K1109 Series Card Reader User Manual DS-K1109 Series Card Reader User Manual Legal Information 2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website ( https://

www.hikvision.com/ ). Please use this Manual with the guidance and assistance of professionals trained in supporting the Product. Trademarks Hikvision in various jurisdictions. Other trademarks and logos mentioned are the properties of their respective owners. and other Hikvision's trademarks and logos are the properties of Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED AS IS AND WITH ALL FAULTS AND ERRORS. HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE i DS-K1109 Series Card Reader User Manual DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed. To protect data, the development of Hikvision devices incorporates privacy by design principles. For example, for device with facial recognition features, biometrics data is stored in your device with encryption method; for fingerprint device, only fingerprint template will be saved, which is impossible to reconstruct a fingerprint image. As data controller, you are advised to collect, store, process and transfer data in accordance with the applicable data protection laws and regulations, including without limitation, conducting security controls to safeguard personal data, such as, implementing reasonable administrative and physical security controls, conduct periodic reviews and assessments of the effectiveness of your security controls. ii DS-K1109 Series Card Reader User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. iii DS-K1109 Series Card Reader User Manual EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE"

and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see:

www.recyclethis.info 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury

(Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see:www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements. iv DS-K1109 Series Card Reader User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions:

Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death. Cautions: Follow these precautions to prevent potential injury or material damage. Danger:

All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value. Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard. Please make sure that the power has been disconnected before you wire, install or dismantle the device. When the product is installed on wall or ceiling, the device shall be firmly fixed. If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) Cautions:

Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage). Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. The device cover for indoor use shall be kept from rain and moisture. Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger). v DS-K1109 Series Card Reader User Manual Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time. Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover. Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents. Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs. Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. Please take care of your card and report card loss in time when card is lost. Multiple card types are supported. Please select an appropriate card type according to the card performance and the usage scenarios. vi DS-K1109 Series Card Reader User Manual Available Models Product Name Model Wireless Card Reader DS-K1109DB DS-K1109DKFB DS-K1109DKFB-QR DS-K1109DKB DS-K1109DKB-QR DS-K1109EB DS-K1109EKFB DS-K1109EKFB-QR DS-K1109EKB DS-K1109EKB-QR 13.56 MHz Card Presenting Frequency, Bluetooth 13.56 MHz Card Presenting Frequency, Bluetooth 13.56 MHz Card Presenting Frequency, Bluetooth 13.56 MHz Card Presenting Frequency, Bluetooth 13.56 MHz Card Presenting Frequency, Bluetooth 125 KHz Card Presenting Frequency, Bluetooth 125 KHz Card Presenting Frequency, Bluetooth 125 KHz Card Presenting Frequency, Bluetooth 125 KHz Card Presenting Frequency, Bluetooth 125 KHz Card Presenting Frequency, Bluetooth Use only power supplies listed in the user instructions:

Model Manufacturer Standard TS-A018-120015Ec Shenzhen Transin Technologies Co., Ltd CEE vii DS-K1109 Series Card Reader User Manual Contents Chapter 1 Overview .................................................................................................................... 1 Chapter 2 Appearance ................................................................................................................ 2 2.1 Front View .............................................................................................................................. 2 2.2 Rear View ............................................................................................................................... 2 Chapter 3 Installation ................................................................................................................. 4 3.1 DIP Switch Description ........................................................................................................... 4 3.2 Wiring Cables ......................................................................................................................... 5 3.2.1 Description of Cable ...................................................................................................... 5 3.2.2 Set RS-485 Communication Mode ................................................................................ 5 3.2.3 Set Wiegand Communication Mode ............................................................................. 6 Chapter 4 Sound Prompt and Indicator ....................................................................................... 8 Appendix A. Preventive and Cautionary Tips .............................................................................. 9 Appendix B. Communication Matrix and Device Command ...................................................... 10 viii DS-K1109 Series Card Reader User Manual Chapter 1 Overview The card reader is a kind of high-performance product, with a 32 bit high-speed processor. It communicates with access controller via either RS-485 protocol or Wiegand protocol. And a built-in tamper-proof module helps to protect card reader from malicious damage. As to the physical appearance, the PC+ABS material makes water proof and dust proof possible in poor environment. 1 DS-K1109 Series Card Reader User Manual Chapter 2 Appearance 2.1 Front View The front view of card reader is shown below:

Figure 2-1 Front View 2.2 Rear View The rear view of card reader is shown below:

2 DS-K1109 Series Card Reader User Manual Figure 2-2 Rear View 3 DS-K1109 Series Card Reader User Manual Chapter 3 Installation 3.1 DIP Switch Description The DIP switch module is shown below. The No. of DIP switch from left to right is 1 to 8. When the switch is towards ON, it means the switch is enabled, otherwise, the switch is off. If you set the DIP switch like the figure displayed below, its binary value is 00001100, and its decimal value is 12. Table 3-1 Description of DIP Switch No. Description DIP Switch Status 1 to 4 Address of RS-485 1: 1 0: 0 5 6 7 8 Card Security Note For DS-K1108AE/AEK, the DIP switch is reserved. 1: Enable M1 card encryption function, and disable door open via NFC card. 0: Disable M1 card encryption function, enable door open via NFC card, and read card No. Wiegand protocol or RS-485 protocol. 1: Wiegand protocol 0: RS-485 protocol Wiegand Protocol (available when No. 6 is 1) 1: Wiegand protocol of 26-bit;

0: Wiegand protocol of 34-bit. Matched Resistance (available for RS-485 protocol) 1: Enable 0: Disable 4 DS-K1109 Series Card Reader User Manual 3.2 Wiring Cables Wire the cables between controller and card reader, thus to establish the communication between them. 3.2.1 Description of Cable The description of 10 cables is shown below. Table 3-2 Description of Cable Color Description Orange Brown White Green Blue Yellow Red Black Gray Purple Wiegand ERR (Available for Wiegand Protocol) Wiegand OK (Available for Wiegand Protocol) Wiegand W1 (Available for Wiegand Protocol) Wiegand W0 (Available for Wiegand Protocol) RS-485-

RS-485+

PWR (+12 VDC) GND TAMPER Control Beep Control (Available for Wiegand Protocol) 3.2.2 Set RS-485 Communication Mode Steps 1. Set the DIP switch of No. 6 as 0. 2. Set the DIP switch of No. 1 ~ 5 for RS-485 address and reading card mode. For details, refers to DIP Switch Description . 3. Wire the cable between controller and card reader as shown below. 5 DS-K1109 Series Card Reader User Manual Figure 3-1 Wiring for RS-485 Communication Mode 3.2.3 Set Wiegand Communication Mode Steps 1. Set the DIP switch of No. 6 as 1. 6 DS-K1109 Series Card Reader User Manual 2. Set the DIP switch of No. 5 and 7 for reading card mode and Wiegand protocol. For details, refers to DIP Switch Description . 3. Wiring the cable between controller and card reader as shown below. Figure 3-2 Wiring for Wiegand Communication Mode 7 DS-K1109 Series Card Reader User Manual Chapter 4 Sound Prompt and Indicator After the card reader is powered on, LED status indicator will turn green and flashing for 1 time. Then it will turn red and flashing for 3 times. At last the buzzer will send out a beep sound indicating the starting up process is completed. When using the card reader, it will send out different sounds prompt and the LED indicator on it will have different statuses. You can refer to tables below for detailed information. Table 4-1 Description of Prompt Sound Sound Prompt Description One Beep Presenting card prompt Pressing keys prompt Prompt of pressing key for too long time when inputting card No. Time out prompt for pressing keys or presenting card. For authentication: prompt for entering the password after presenting the card. Two Rapid Beeps Three Slow Beeps The operation of pressing keys or swiping card is valid. The operation of pressing keys or swiping card is invalid. Rapidly Continuous Beeps Prompt for tamper-proof alarm. Slowly Continuous Beeps The card reader is unencrypted. Prompt for buzzer alarm. LED Indicator Status Flashing Green for 1 Time and Flashing Red for 3 Times Flashing Green Table 4-2 Description of LED Switch The card reader is power on. Description For Card + Password authentication: prompt for entering the password after presenting the card. Solid Green for 2 s The operation of pressing keys or presenting card is valid. Solid Red Card reader is working normally. Flashing Red for 3 Times The operation of pressing keys or presenting card is invalid. Flashing Red For RS-485 protocol: Registering failed or card reader is offline. 8 DS-K1109 Series Card Reader User Manual Appendix A. Preventive and Cautionary Tips To guarantee the card reader works properly, please read and obey the notes below. If the card reader is powered by the controller, the power supply distance is recommended to be no longer than 100m. If the distance is longer than 100 m, you are advised to power the card reader by external 12 V (range: -%10 to +%10) DC power supply, which is non-switched and linear. To guarantee the communication between the controller and the card reader, you must use RVVP cable above 0.5 to connect them. If the card reader is installed outside or in environment easy to permeable, it is advisable to install a waterproof shield. If you need to install several card readers, the distance among them must over 30 cm. To reduce the noise in long distance transmission, the shield of cable should connect to the GND of both controller and card reader terminal. Please take care of your card and report card loss in time when card is lost. If you require a higher security level, use multiple authentication modes. Multiple card types are supported. Please select an appropriate card type according to the card performance and the usage scenarios. 9 DS-K1109 Series Card Reader User Manual Appendix B. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure B-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands. Note that the command list contains all commonly used serial ports commands for all Hikvision access control and video intercom devices. Figure B-2 Device Command 10 UD29976B

HIK VISION C |

Card Reader Model: DS-K1109EKFB-QR UP: 12V===0.5A SN: _A12345678

| | (MMT TI (MM FCC ID:ADTD-K1109EKFBQR Made in China Manufacturer: Hangzhou Hikvision Digital Technology Co.,Ltd. Address: No.555 Qianmo Road, Binjiang District,Hangzhou 310052, China This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)this device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name Hangzhou Hikvision Digital Technology Co., Ltd. Address Grantee Code FCC ID No. 555 Qianmo Road, Binjiang District, Hangzhou 310052, China 2ADTD 2ADTD-K1109EKFBQR Authorized Contact Name Long Cheng Contact Email Contact Phone chenglong6@hikvision.com

+8618969187825 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

a) b) c) d) e) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Date: 2022-09-19 Applicant Signature:

Print Name:

Title:

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Long Cheng Testing & Certification Engineer Applicant Declaration Rev:0.0

Hangzhou Hikvision Digital Technology Co., Ltd. TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2ADTD-K1109EKFBQR To whom it may concern:

Date: 2022-09-19 We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Hangzhou Hikvision Digital Technology Co., Ltd. This authorization is valid until further written notice from the applicant. Name (Printed): Long Cheng Title: Testing & Certification Engineer Signature:

On behalf of Company: Hangzhou Hikvision Digital Technology Co., Ltd. Telephone: +8618969187825

Hangzhou Hikvision Digital Technology Co., Ltd. To:

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Hangzhou Hikvision Digital Technology Co., Ltd. No. 555 Qianmo Road, Binjiang District, Hangzhou 310052, China Regarding:

Confidentiality Request regarding application for FCC ID: 2ADTD-K1109EKFBQR LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Signature:

Printed Name (on file with the FCC associated with the Grantee Code): Long Cheng Title: Testing & Certification Engineer Company Name: Hangzhou Hikvision Digital Technology Co., Ltd.

Hangzhou Hikvision Digital Technology Co., Ltd. Current Date: 2022-09-19 To:

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. No. 588 West Jindu Road, Songjiang District, Shanghai, China. 201612 Dear Sir/Madam, Subject: Declaration Letter about Identity of Products

*WE (Hangzhou Hikvision Digital Technology Co., Ltd.) HEREBY DECLARED THAT Product Description Card Reader Model No. DS-K1109EKFB,DS-K1109EKB-QR,DS-K1109EKB,DS-K1109EB, DS-K1109EKFB-QRUHK,DS-K1109EKFB-QRCKV,DS-K1109EKFB-QRUVS, DS-K1109EKFB-QRKVO,DS-K1109EKFB-QRHUN,DS-K1109EKFBUHK, DS-K1109EKFBCKV,DS-K1109EKFBUVS,DS-K1109EKFBKVO, DS-K1109EKFBHUN,DS-K1109EKB-QRUHK,DS-K1109EKB-QRCKV, DS-K1109EKB-QRUVS,DS-K1109EKB-QRKVO,DS-K1109EKB-QRHUN, DS-K1109EKBUHK,DS-K1109EKBCKV,DS-K1109EKBUVS,DS-K1109EKBKVO, DS-K1109EKBHUN,DS-K1109EBUHK,DS-K1109EBCKV,DS-K1109EBUVS, Manufacturers Hangzhou Hikvision Digital Technology Co., Ltd. DS-K1109EBKVO,DS-K1109EBHUN Name Manufacturers No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China Address

*Except that the model number,trade name,color and appearance deviation, are identical with the original product as follows:

Note: The definition of identical should be electrically identical. A device will be considered to be electrically identical if no changes are made to the devices schematics, board layouts, component layouts, chip sets, resistors and all other electrical aspects of the device are identical with the model(s) we chose to be tested by SGS. Model No. ():

DS-K1109EKFB-QR Manufacturers Name (): Hangzhou Hikvision Digital Technology Co., Ltd. Manufacturers Address ):

No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China Hangzhou Hikvision Digital Technology Co., Ltd. Sincerely, Signature ():

Printed Name ():

Long Cheng Position/Title ():

Testing & Certification Engineer Contact Number ():

+8618969187825