FCC ID: 2ADTD-KDE Card Reader Module

Video Intercom Card Reader Module Quick Start Guide Scan to get detailed User Manual Video Intercom Card Reader ModuleQuick Start Guide Quick Start Guide 2018 Hangzhou Hikvision Digital Technology Co., Ltd. This quick start guide is intended for users of card reader module: DS-KD-M (13.56 MHz) and DS-KD-E (125 KHz). Nametag module is the component of the module door station. Use it along with the main unit. It includes instructions on how to use the Product. The software embodied in the Product is governed by the user license agreement covering that Product. About this Manual This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision Digital Technology Co., Ltd. (Hikvision) reserves all rights to this manual. This manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Trademarks and other Hikvision marks are the property of Hikvision and are registered trademarks or the subject of applications for the same by Hikvision and/or its affiliates. Other trademarks mentioned in this manual are the properties of their respective owners. No right of license is given to use such trademarks without express permission. Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL. HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, SECURITY BREACHES, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF OR RELIANCE ON THIS MANUAL, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR CERTAIN DAMAGES, SO SOME OR ALL OF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. ii Video Intercom Card Reader ModuleQuick Start Guide Support Should you have any questions, please do not hesitate to contact your local dealer. iii Video Intercom Card Reader ModuleQuick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see:

www.recyclethis.info iv Video Intercom Card Reader ModuleQuick Start Guide 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see:

www.recyclethis.info v Video Intercom Card Reader ModuleQuick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions:

Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Cautions Follow these precautions to prevent potential injury or material damage. Warnings Follow these safeguards to prevent serious injury or death. Warnings The working temperature of the device is from -40 C to 60 C. All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value. Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard. Please make sure that the power has been disconnected before you wire, install or dismantle the device. When the product is installed on wall or ceiling, the device shall be firmly fixed. If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) The power supply must conform to LPS. The recommended adaptor models and manufacturers are shown as below. Use the attached adaptor, and do not change the adaptor randomly. Model Manufacturer Standard ADS-24S-12 1224GPCN KPL-060F-VI Shenzhen Honor Electronic Co., Ltd. Channel Well Technology Co., Ltd. GB GB vi Video Intercom Card Reader ModuleQuick Start Guide Cautions Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage). Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time. Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents. Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs. Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. The warranty does not apply to the product defects and failures arisen as a result of improper mounting (in contradiction herewith). When the proper mounting instructions are not met, water might get in and destroy the electronics. vii Video Intercom Card Reader ModuleQuick Start Guide Table of Contents 1 Overview ...................................................................................................... 1 2 Terminal and Wiring ..................................................................................... 2 3 Installation ................................................................................................... 3 3.1 Configure Sub Module Address ............................................................................... 3 3.2 One-Module Installation .......................................................................................... 4 3.2.1 One-Module Surface Mounting ........................................................................ 4 3.2.2 One-Module Flush Mounting ............................................................................ 8 3.3 Two-Module Installation ........................................................................................ 12 3.3.1 Two-Module Surface Mounting ...................................................................... 12 3.3.2 Two-Module Flush Mounting .......................................................................... 17 3.4 Three-Module Installation ..................................................................................... 22 3.4.1 Three-Module Surface Mounting .................................................................... 22 3.4.2 Three-Module Flush Mounting ....................................................................... 27 3.5 More-than-Three Module Installation ................................................................... 33 3.5.1 More-than-Three Module Surface Mounting .................................................. 33 3.5.2 More-than-Three Module Flush Mounting ..................................................... 39 4 Remote Operation ...................................................................................... 48 4.1 Activate Main Unit ................................................................................................. 48 4.2 Edit Network Parameters ....................................................................................... 49 4.3 Add Device ............................................................................................................. 50 viii Video Intercom Card Reader ModuleQuick Start Guide 1 Overview Card reader module supports issue cards and unlock door via swiping card. It works together with the main unit and other sub modules. Its appearance is shown as below. Figure 1-1 Card Reader Module Appearance Table 1-1 Appearance Description Description Card Reading Area Module-connecting Interface(output) Module-connecting Interface(input) Debug Port No. 1 2 3 4 The module connecting interface is used to connect with main unit or other function module, such as nametag module, keypad module, card reader module, etc. All these modules (except main unit) are known as sub module. 1 Video Intercom Card Reader ModuleQuick Start Guide 2 Terminal and Wiring The card reader modules interfaces and terminals as below:

Figure 2-1 Terminals and Interfaces Table 2-1 Descriptions of Terminals and Interfaces No. Interface Description A1 A2 A3 A4 A5 A6 A7 A8 485-

485+

12V IN GND 485-

485+

12V OUT GND Module-connecting Interface (Input) Module-connecting Interface (Output) 2 Video Intercom Card Reader ModuleQuick Start Guide 3 Installation Before you start:

Make sure the device in the package is in good condition and all the assembly parts are included. Sub module must work along with the main unit. Set the sub module address before start the installation steps. Make sure the place for surface mounting is flat. Make sure all the related equipment is power-off during the installation. Tools that you need to prepare for installation:

Drill (6), cross screwdriver (PH1*150 mm), and gradienter. Buy corresponding accessory package for installation. The accessory package model and its suitable installation method as below:

Package Model DS-KD-ACW1 DS-KD-ACW2 DS-KD-ACW3 DS-KD-ACF1 DS-KD-ACF2 DS-KD-ACF3 Mounting Method Note One-Module Surface Mounting Two-Module Surface Mounting Three-Module Surface Mounting One-Module Flush Mounting Two-Module Flush Mounting Three-Module Flush Mounting Install the device according to the instructions. Not all the lines in the accessory package will be used. 3.1 Configure Sub Module Address You need to set the sub module address via DIP before installation. Steps:

1. Remove the rubber cover on the sub module rear panel to expose the DIP switch. 3 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-1 DIP Switch 2. Set the sub module address according to the DIP rules, and install the rubber cover back. Digit 1, 2, 3, 4 are used to coding the sub module address; Digit 5, 6, 7, 8 are reserved. Valid sub module address range is 1 to 8. The No. should be unique for sub modules that connected to the same main unit. The sub module address and corresponding switch status as below. Sub Module 1 2 3 4

.5 6 7 8 Address Digit 1 Digit 2 Digit 3 Digit 4 ON OFF ON OFF ON OFF ON OFF OFF ON ON OFF OFF ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF ON 3.2 One-Module Installation 3.2.1 One-Module Surface Mounting Mounting Frame 4 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-2 Front and Side View The dimension of one module mounting frame is: 117(L)107(W)32.7(D) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. Steps:

1. Paste the installation Sticker 1 onto the wall. Make sure the sticker is placed leveled via measuring with the gradienter. 2. Chisel 4 holes with drill align to the screw holes on the sticker. The suggested size of hole is 6 (diameter) 25 (depth) mm. The suggested length of cables left outside is 100 mm. 5 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-3 Chisel Screw Hole 3. Remove the sticker and insert the expansion sleeves into the screw holes. 4. Fix the mounting frame onto the wall with 4 expansion bolts. 6 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-4 Fix the Mounting Frame The mounting frame should be placed exactly as below for this step. The tamper plate should be at the low-right. 5. Connect the cables to the corresponding interfaces of the main unit and insert it into the frame. 7 Video Intercom Card Reader ModuleQuick Start Guide 6. Use the hexagon wrench in the package fix the cover onto the frame. Figure 3-5 Insert the Main unit Figure 3-6 Fix the Cover 3.2.2 One-Module Flush Mounting Gang Box 8 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-7 Front and Side View Figure 3-8 Appearance Description 9 Video Intercom Card Reader ModuleQuick Start Guide The dimension of one-module gang box is: 115(L)134(W)56(D) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. Steps:

1. Cave the installation hole, and pull the cable out. The suggested dimension of installation hole is 118(L)108(W)45.5(D) mm. The suggested length of cables left outside is 100 mm. Figure 3-9 Cave the Installation Hole 2. Remove the plastic sheet in the cable entry. 3. Insert the gang box into the hole and pull out the cables through the cable entry. Mark the screw holes position with a marker, and take out the gang box. Figure 3-10 Mark the Screw Holes 4. Chisel 4 holes with drill align to marks on the wall, and insert the expansion sleeves into the screw holes. The suggested size of hole is 6 (diameter) 45 (depth) mm. 5. Fix the gang box with 4 expansion bolts. 10 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-11 Fix the Gang Box 6. Fill and level up the gap between the gang box and wall with concrete. Remove the 4 mounting ears with tool after concrete is dry. Figure 3-12 Remove the Mounting Ears 7. Insert the mounting frame together with the locating plates into the hole, and fix it with 4 expansion bolts. 8. Connect the cables to the corresponding interfaces of the main unit and insert it into the gang box. 9. Use the hexagon wrench in the package fix the cover. Figure 3-13 Insert the Main unit 11 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-14 Fix the Cover 3.3 Two-Module Installation 3.3.1 Two-Module Surface Mounting Mounting Frame 12 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-15 Front and Side View The dimension of two-module mounting frame is: 219(L)107 (W)32.7(D) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. Steps:

1. Paste the installation Sticker 1 onto the wall. Make sure the sticker is placed leveled via measuring with the gradienter. 2. Chisel 4 holes with drill align to the screw holes on the sticker. The suggested size of hole is 6 (diameter) 25 (depth) mm. The suggested length of cables left outside is 270 mm. 13 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-16 Chisel Screw Hole 3. Remove the sticker and insert the expansion sleeves into the screw holes. 4. Fix the mounting frame onto the wall with 4 expansion bolts. Figure 3-17 Fix the Mounting Frame 14 Video Intercom Card Reader ModuleQuick Start Guide The mounting frame should be placed exactly as below for this step. The tamper plate should be at the low right of the first grid. 5. Thread the module-connecting line across the thread hole of the frame. Pass the main unit connecting lines across the thread hole to the upper grid. Figure 3-18 Placement of Lines 6. Connect the cables and module-connecting line to the corresponding interfaces of the main unit, then place the main unit into the upper grid. Connect the other end of the module-connecting line to the input interface of the sub module. Organize the line with cable tie in the package. The suggested line connection picture as below. 15 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-19 Line Connection Effect Picture 7. Insert the modules in to the frame after wiring. Main unit must be placed in the top grid. 8. Use the hexagon wrench in the package fix the cover onto the frame. Figure 3-20 Insert the Modules 16 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-21 Fix the Cover 3.3.2 Two-Module Flush Mounting Gang Box Figure 3-22 Front and Side View 17 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-23 Appearance Description The dimension of one-module gang box is: 237(L)134(W)56(D) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. Steps:

1. Cave the installation hole, and pull the cable out. The suggested dimension of installation hole is 220(L)108(W)45.5(D) mm. The suggested length of cables left outside is 270 mm. 18 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-24 Cave the Installation Hole 2. Remove the plastic sheet of the cable entry which will be used. 3. Insert the gang box into the hole and pull out the cables through the cable entry. Mark the screw holes position with a marker, and take out the gang box. Figure 3-25 Mark the Screw Holes 4. Chisel 4 holes with drill align to marks on the wall, and insert the expansion sleeves into the screw holes. The suggested size of hole is 6 (diameter) 45 (depth) mm. 5. Fix the gang box with 4 expansion bolts. 19 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-26 Fix the Gang Box 6. Fill and level up the gap between the gang box and wall with concrete. Remove the mounting ears with tool after concrete is dry. Figure 3-27 Remove the Mounting Ears 7. Connect wires and insert the modules:

a. Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the main unit, then place the main unit into the upper grid. b. Connect the other end of Cable 2 to the input interface of the sub module. Insert it into the lower grid. 20 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-28 Connect Wires and Insert Modules Cable 1 refers to the cables pulled out from the wall that connected to the main unit. Cable 2 refers to the module-connecting line in the accessory package. 8. Use the hexagon wrench in the package fix the cover. Figure 3-29 Fix the Cover 21 Video Intercom Card Reader ModuleQuick Start Guide 3.4 Three-Module Installation 3.4.1 Three-Module Surface Mounting Installation Frame Figure 3-30 Front and Side View The dimension of two-module mounting frame is: 320.8(L)107 (W)32.7(D) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. Steps:

1. Paste the installation Sticker 1 onto the wall. Make sure the sticker is placed leveled via measuring with the gradienter. 2. Chisel 4 holes with drill align to the screw holes on the sticker. The suggested size of hole is 6 (diameter) 25 (depth) mm. The suggested length of cables left outside is 270 mm. 22 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-31 Chisel Screw Hole 3. Remove the sticker and insert the expansion sleeves into the screw holes. 4. Fix the mounting frame onto the wall with 4 expansion bolts. Figure 3-32 Fix the Mounting Frame The mounting frame should be placed exactly as below for this step. The tamper plate should be at the low right of the first grid. 23 Video Intercom Card Reader ModuleQuick Start Guide 5. Thread the module-connecting lines across the thread holes of the frame. Pass the main unit connecting lines across the thread hole to the top grid. 24 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-33 Placement of Lines 6. Connect the cables and module-connecting line 1 to the corresponding interfaces of the main unit, then place the main unit into the upper grid. Connect the other end of the module-connecting line1 to the input interface of the sub module. Connect two sub modules via module-connecting line 2. Organize the line with cable tie in the package. The suggested line connection picture as below. 25 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-34 Line Connection Effect Picture 7. Insert the modules in to the frame after wiring. Main unit must be placed in the top grid. Figure 3-35 Insert the Modules 26 Video Intercom Card Reader ModuleQuick Start Guide 8. Use the hexagon wrench in the package fix the cover onto the frame. Figure 3-36 Fix the Cover 3.4.2 Three-Module Flush Mounting Gang Box 27 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-37 Front and Side View 28 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-38 Appearance Description The dimension of one-module gang box is: 338.8(L)134(W)56(D) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. Steps:

1. Cave the installation hole, and pull the cable out. The suggested dimension of installation hole is 321.8(L)108(W)45.5(D) mm. The suggested length of cables left outside is 270 mm. 29 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-39 Cave the Installation Hole 2. Remove the plastic sheet of the cable entry which will be used. 3. Insert the gang box into the hole and pull out the cables through the cable entry. Mark the screw holes position with a marker, and take out the gang box. Figure 3-40 Mark the Screw Holes 4. Chisel 4 holes with drill align to marks on the wall, and insert the expansion sleeves into the screw holes. The suggested size of hole is 6 (diameter) 45 (depth) mm. 5. Fix the gang box with 4 expansion bolts. 30 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-41 Fix the Gang Box 6. Fill and level up the gap between the gang box and wall with concrete. Remove the mounting ears with tool after concrete is dry. Figure 3-42 Remove the Mounting Ears 7. Connect wires and insert the modules:

a. Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the Main Unit, then place the Main Unit into the upper grid. b. Connect the other end of Cable 2 to the input interface of Sub Module 1. Connect one end of Cable 3 to the output interface of Sub Module 1 and insert it into the middle grid. c. Connect the other end of Cable 3 to the input interface of Sub Module 2. Insert it into the bottom grid. 31 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-43 Connect Wires and Insert Modules Cable 1 refers to the cables pulled out from the wall that connected to the main unit. Cable 2 and Cable 3 refer to the module-connecting line in the accessory package. 8. Use the hexagon wrench in the package to fix the cover onto the gang box. Figure 3-44 Fix the Cover 32 Video Intercom Card Reader ModuleQuick Start Guide 3.5 More-than-Three Module Installation 3.5.1 More-than-Three Module Surface Mounting Figure 3-45 Front and Side View It takes two three-module mounting frames. The dimension of three-module mounting frame is: 320.8(L)107 (W)32.7(D) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. Steps:

1. Paste two Sticker 1 onto the wall. Make sure the stickers are placed leveled via measuring with the gradienter. 2. Chisel 8 holes with drill align to the screw holes on the sticker. The suggested size of hole is 6 (diameter) 25 (depth) mm. The suggested length of cables left outside is 270 mm. 3. Pull out the cable through the cable hole of the left sticker. 33 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-46 Chisel Screw Hole 4. Remove the stickers and insert the expansion sleeves into the screw holes. 5. Thread the module-connecting line (400 mm) and grounding line across the thread hole of both frames. Figure 3-47 Place the Grounding Line and Module-Connecting Line There are 6 module-connecting lines in the package: 190 mm *4 and 400 mm*2. 34 Video Intercom Card Reader ModuleQuick Start Guide Take the 400 mm one for this step. The green-yellow line in the package is for grounding. 6. Fix the mounting frame onto the wall with 8 expansion bolts. Figure 3-48 Fix the Mounting Frame The mounting frame should be placed exactly as below for this step. The tamper plate should be at the low right of the first grid. 35 Video Intercom Card Reader ModuleQuick Start Guide 7. Pass the main unit connecting lines across the thread hole to the top grid of the left frame. Thread the module-connecting line (190 mm) across the thread hole of the frame. The lines should be placed as below:

Figure 3-49 Placement of Lines 8. Connect the cables and module-connecting line 1 to the corresponding interfaces of the main unit, then place the main unit into the upper grid. Connect the other end of the module-connecting line1 to the input interface of the sub module. Connect all sub modules via module-connecting lines. Organize the line with cable tie in the package. The suggested line connection picture as below. 36 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-50 Line Connection Effect Picture 9. Insert the modules in to the frame after wiring. Main unit must be placed in the top grid on the left. 37 Video Intercom Card Reader ModuleQuick Start Guide 10. Pull the grounding line out and fixed its two end to the screw on the cover. Figure 3-51 Insert the Modules Figure 3-52 Connect the Grounding Line to the Cover 11. Use the hexagon wrench in the package fix the cover onto the frame. 38 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-53 Fix the Cover 3.5.2 More-than-Three Module Flush Mounting Gang Box 39 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-54 Front and Side View 40 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-55 Appearance Description It takes two three-module gang boxes. The dimension of the gang box is: 338.8(L) 134 (W)56(D) mm. The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. Steps:

1. Cave the installation hole, and pull the cable out. The suggested dimension of installation hole is 321.8(L)315(W)45.5(D) mm. The suggested length of cables left outside is 270 mm. 41 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-56 Cave the Installation Hole 2. Connect the two gang boxes as the below. Figure 3-57 Cave the Installation Hole 3. Remove the plastic sheet of the cable entry which will be used. 4. Remove the plastic sheets on the side of the gang boxes (shown as 1 and 2) blow:

42 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-58 Remove the Plastic Sheets 5. Insert the gang boxes into the hole and pull out the cables through the cable entry. Mark the screw holes position with a marker, and take out the gang boxes. Figure 3-59 Mark the Screw Holes 6. Chisel 8 holes with drill align to marks on the wall, and insert the expansion sleeves into the screw holes. The suggested size of hole is 6 (diameter) 45 (depth) mm. 7. Fix the gang boxes with 8 expansion bolts. 43 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-60 Fix the Gang Boxes 8. Fill and level up the gap between the gang box and wall with concrete. Remove the mounting ears with tool after concrete is dry. Figure 3-61 Remove the Mounting Ears 9. Pass the grounding line through the cable entries. 44 Video Intercom Card Reader ModuleQuick Start Guide Figure 3-62 Place the Grounding Line The green-yellow line in the package is for grounding. 10. Connect wires and insert the modules. a. Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the Main Unit, then place the Main Unit into the upper grid of the left gang box. b. Connect the other end of Cable 2 to the input interface of Sub Module 1. Connect one end of Cable 3 to the output interface of Sub Module 1 and insert it into the middle grid of the left gang box. c. Finish the wiring and inserting according to the cable number and the position shown as below. 45 Video Intercom Card Reader ModuleQuick Start Guide The cables connect to each module shown as below:

Figure 3-63 Install Mounting Frames Figure 3-64 Install Mounting Frames Cable 2,3,5 and 6 are the module-connecting lines (190 mm) in the package. 46 Video Intercom Card Reader ModuleQuick Start Guide Cable 4 is the module-connecting line (400 mm) in the package. Main unit must be put in the top grid. 11. Pull the grounding line out and fixed its two end to the screw on the cover. Figure 3-65 Connect the Grounding Line to the Cover 12. Use the hexagon wrench in the package fix the cover onto the gang box. Figure 3-66 Fix the Cover 47 Video Intercom Card Reader ModuleQuick Start Guide 4 Remote Operation 4.1 Activate Main Unit Card reader module cannot work alone. It need to use together with main unit. You need to activate the main unit first. You can configure and operate the video intercom devices via iVMS-4200. Default parameters of door station are as follows:

Default IP Address: 192.0.0.65. Default Port No.: 8000. Default User Name: admin. Steps:

1. Run iVMS-4200, enter Device Management, check the Online Device area. 2. Select an inactivated device and click the Activate button. 3. Create a password, and confirm the password. 48 Video Intercom Card Reader ModuleQuick Start Guide STRONG PASSWORD RECOMMENDED We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories:

upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 4. Click the OK button to activate the device. When the device is not activated, the basic operation and remote operation of device cannot be performed. You can hold the Ctrl or Shift key to select multiple devices in the online devices, and click the Activate button to activate devices in batch. 4.2 Edit Network Parameters Purpose:

To operate and configure the device via LAN (Local Area Network), you need connect the device in the same subnet with your PC. You can edit network parameters via iVMS-

4200 software. Steps:

1. Select an online activated device and click the Modify Netinfo button. 2. Change the device IP address and gateway address to the same subnet with your computer. 3. Enter the password and click the OK button to activate the network parameters modification. 49 Video Intercom Card Reader ModuleQuick Start Guide The default port No. is 8000. The default IP address of the door station is 192.0.0.65. After editing the network parameters of device, you should add the devices to the device list again. 4.3 Add Device To configure the device remotely, you need to add the device to iVMS-4200. Steps:

1. Select the activated device and click Add to Client. 2. Enter corresponding information, and click Add. 50 Video Intercom Card Reader ModuleQuick Start Guide Device is added to the client, check it in the Device for Management area. You can call corresponding residents by press the call buttons on the nametag module. 51 Video Intercom Card Reader ModuleQuick Start Guide 52 UDB