1 Installation Installation Environment:
Indoor installation is supported. The device should be at least 2 meters away from the light, and at least 3 meters away from the window or the door. The additional force shall be equal to three times the weight of the equipment but not less than 50N. The equipment and its associated mounting means shall remain secure during the installation. After the installation, the equipment, including any associated mounting plate, shall not be damaged. 1 Make sure the gang box is installed on the wall. 2 Appearance Camera Camera 103.36 mm 20.7mm IR Light Backlight Direct Sunlight Direct Sunlight through Window Indirect Sunlight through Window Close to Light DS-K1T672 Series Face Recognition Terminal Quick Start Guide UDB 2 Use 1 supplied screw to secure base plate on the gang box. Use another two supplied screws to secure the mounting plate on the base plate. Route the cables through the cable hole of the mounting plate, and connect to the correcsponding external devices cables. 3 Align the device with the mounting plate and hang the the device on the mounting plate. Use 1 supplied screw to secure the device on the mounting plate. Wiring Terminal Network Interface TAMPER Debugging Port (For debugging only) IR Light Screen Card Presenting Area m m 8 5 8 1
. m m 5 1 0 2 0 1
. 3.1 Device Wiring (Normal) 2019 Hangzhou Hikvision Digital Technology Co., Ltd. It includes instructions on how to use the Product. The software embodied in the Product is governed by the user license agreement covering that Product. About this Manual This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision Digital Technology Co., Ltd. (Hikvision) reserves all rights to this manual. This manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Trademarks and other Hikvision marks are the property of Hikvision and are registered trademarks or the subject of applications for the same by Hikvision and/or its aliates. Other trademarks mentioned in this manual are the properties of their respective owners. No right of license is given to use such trademarks without express permission. Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED AS IS, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed. To protect data, the development of Hikvision devices incorporates privacy by design principles. For example, for device with facial recognition features, biometrics data is stored in your device with encryption method; for ngerprint device, only ngerprint template will be saved, which is impossible to reconstruct a ngerprint image. As data controller, you are advised to collect, store, process and transfer data in accordance with the applicable data protection laws and regulations, including without limitation, conducting security controls to safeguard personal data, such as, implementing reasonable administrative and physical security controls, conduct periodic reviews and assessments of the eectiveness of your security controls. Scan the QR code to get the user manual for detailed information. Use only power supplies listed in the user instructions:
Model Manufacture Standard ADS-26FSG-12 12024EPG Shenzhen Honor Electronic Co.,Ltd MSA-C2000IC12.0-24P-DE MOSO Technology Co.,Ltd ADS-26FSG-12 12024EPB Shenzhen Honor Electronic Co.,Ltd ADS-26FSG-12 12024EPCU/EPC Shenzhen Honor Electronic Co.,Ltd ADS-26FSG-12 12024EPI-01 Shenzhen Honor Electronic Co.,Ltd ADS-26FSG-12 12024EPBR Shenzhen Honor Electronic Co.,Ltd PG PDE PB PCU PI PBR 91.840.15 mm microUSB
(Use microUSB to USB cabe to connect with USB interface) PSAM Card Slot
(Reserved) The gures are for reference only. Power Input Alarm Input Alarm Output RS-485 Wiegand Door Lock Network Interface Group B IN1 GND IN2 NC COM NO GND GND GND BTN GND Group D B1 B2 B3 B4 B5 B6 C1 C2 C3 C4 C5 C6 D1 D2 D3 D4 D5 D6 D7 Red Black Yellow/Blue Black Yellow/Orange Yellow/Purple Yellow/Brown Yellow/Red Yellow Blue Black Green White Black Alarm Input Device Power Supply
(NC)
(NO) Alarm Output Device Alarm Output Device 12V Power Supply Wiegand Card Reader White/Purple White/Yellow White/Red Yellow/Green Black Yellow/Grey Yellow/Black
(NC)
(COM)
(NO) NO COM NC Electric Dropbolt Power Supply Electric Strike Door Contact NO COM NC Exit Button When connecting door magnetic sensor and exit button, the device and the RS-485 card reader should use the common ground connection. The Wiegand termimal here is a Wiegand input terminal. You should set the face recognition terminals Wiegand direction to Input. If you should connect to an access controller, you should set the Wiegand direction to Output. For details, see Setting Wiegand Parameters in Communication Settings in the user manual. The suggested external power supply for door lock is 12 V, 1A. The suggested external power supply for Wiegand card reader is 12 V, 1 A. For wiring the re system, see the user manual. 3.2 Device Wiring (With Secure Door Control Unit) 4 Activation 5 Two-Way Audio Face Recognition Terminal Secure Door Control Unit Power Input Sensor Input SENSOR Green/Brown Black NO COM NC Door Contact Exit Button RS-485 Yellow B1 Blue B2 B3 Black Secure Door Control Unit Wiring Terminal Exit Button BUTTON Green/Black Black Power on and wire the network cable after installation. You should activate the device before the rst login. Activate Device If the device is not activated yet, it will enter the Activate Device page after powering on. Steps:
1. Create a password and conrm the password. 2. Tap Activate to activate the device. For other activation methods, see the device user manual. Comrm password. Red Black B1 B2 B3 B4 C1 C2 C3 Lock Output NC COM White/Purple White/Black White/Red
(COM) NO COM NC
(NC) Power
(NO) Electric Dropbolt Electric Strike Enter 8 to 16 characters. Enter Password Comrm Password Enter 8 to 16 characters. Activate STRONG PASSWORD RECOMMENDED We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. The secure door control unit should connect to an external power supply separately. The suggested external power supply is 12 V, 0.5 A. 5 5 After adding the device to the client software, you can call the device from the client software, call the client software from the device, call the center from the device, or call the indoor station form the device. Call Client Software from Device After adding the device on the client software, tap -> , and tap Answer on the pop-up window on the client software to start two-way audio. If the device is added by multiple client softwares and when the device is calling the client software, only the rst client software added the device will pop up the call receiving window. Call Center from Device After adding the device and center on the client software, tap -> to call the center. When the center answers the call, you can start two-way audio. The device will call the center in priority when tap the administrator icon. Call Device from Client Software After adding the device on the client software, you can enter the Live View page. Right click the live view window and click Start Two-Way Audio to start two-way audio. Call Indoor Station from Device After adding the device and the indoor station on the client software, link the added user and the added indoor station, and set a room No. for the indoor station. Tap and enter the room No. And tap to call the indoor station. Tips When Collecting/
Comparing Face Picture Expression Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture on the right. Do not wear hat, sunglasses, or other accessories that can aect the facial recognition function. Do not make your hair cover your eyes, ears, etc. and heavy makeup is not allowed. Positions When Collecting/
Comparing Face Picture
(Recommended Distance: 0.5m) Recommended Height:
1.43m to 1.90m Too High Too Low Posture In order to get a good quality and accurate face picture, position your face looking at the camera when collecting or comparing face pictures. Correct Tilt Side Raise Bow 1.4m 1.4m 6 Add Face Picture 1. Use nger to hold the screen surface for 3 s and slide to right/left and enter the activation password to enter the Home page. 2. Enter the User Management page, tap + to enter the Add User page. 3. Set the user parameters according to actual needs. Only the devices with the ngerprint module support the ngerprint related functions. 4. Tap Face and collect the face information according to the instructions. You can view the captured picture on the screen. Make sure the face picture is in good quality and size. For details about the tips and positions when collecting or comparing the face picture, see the contents on the right. 5. If the picture is in good condition, tap the save icon. Or tap the try again icon to take another face picture. 6. Tap the save icon save the settings. Go back to the initial page to start authentication. For other authentication methods, see the device user manual. Recommended:
Use other authentication methods if the device if aected by the light or other items. 1:N Matching: The device will compare the captured face picture with the ones in the database. 1:1 Matching: The device will compare the captured face picture with the user linked face picture. Size Make sure your face is in the middle of the collecting window. Correct Too Close Too Far Biometric recognition products are not 100% applicable to anti-spoong environments. If you require a higher security level, use multiple authentication modes. 1.4m 1.4m 0.5m 0.5m Too Close Too Far 0.5m 1.2m Regulatory Information FCC Information Please take attention that changes or modication not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the RE Directive 2014/53/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specic battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recy-
clethis.info 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Warnings All the electronic operation should be strictly compliance with the electrical safety regulations, re prevention regulations and other related regulations in your local region. Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value. Do not connect several devices to one power adapter as adapter overload may cause over-heat or re hazard. Please make sure that the power has been disconnected before you wire, install or dismantle the device. When the product is installed on wall or ceiling, the device shall be rmly xed. If smoke, odors or noise rise from the device, turn o the power at once and unplug the power cable, and then please contact the service center. If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) Cautions Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage). Do not place the device in extremely hot (refer to the specication of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. The device cover for indoor use shall be kept from rain and moisture. Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause re danger). Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and aecting the endurance of sensor at the same time. Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the ngers may erode the surface coating of the device cover. Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents. Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs. Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. Biometric recognition products are not 100% applicable to anti-spoong environments. If you require a higher security level, use multiple authentication modes. Indoor and outdoor use. If installing the device indoors, the device should be at least 2 meters away from the light, and at least 3 meters away from the window or the door. If installing the device outdoors, you should apply Sililcone sealant among the cable wiring area to keep the raindrop from entering.