Digital Color Camera User Manual SNC-79440BWN CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense. User Manual Copyright 2017 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization. Disclaimer Hanwha Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the users own responsibility. Hanwha Techwin reserves the right to change the contents of this document without prior notice. Design and specifications are subject to change without prior notice. part names and functions Equipped with the IR LED lights and the illumination sensor, the camera enables you to monitor at all times, day and night. The camera is suitable for both indoor and ourtdoor use. Do not fully expose the camera to rain. The camera must be installed under a shelter to avoid exposure to excessive rain or moisture. a b c d e Name a Lens b IR LED c Illumination Sensor d Pairing Button e Power Cable Description 3.6mm focal length enables you to monitor at a wider field of view Infrared LED lights are controlled by the illumination sensor. Detects incoming light to control the IR LED. Click to do pairing manually. Use to power the camera. English _3 precautions Ensure you read out the following instructions before installing the camera:
Select an area (ceiling or wall) that can withstand 5 times the camera weight Stuck-in or peeled-off cables can cause damage to the product or a fire. For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case. installing the camera The camera can be installed on the wall, ceiling, shelf or a desired position using the provided mounting bracket. 1. Choose an installation site that can sufficiently support the weight of the camera to be installed. 2. Adhere the installation template onto the ceiling and use it as installation locating tool. "Please refer to Page15 (Quick Guide)"
Screw holes for the Camera installation CAMERA FRONT 3. Attach the camera mount to the wall using the supplied screws. 4. Adjust the direction of the camera to the desired direction, and tighten the bracket. 5. Adjust camera angle as needed. 6. Connect the camera cable to the camera. Take caution when installing the camera outdoors because the cable connectors may be wet with moisture or pile up with impurities. Although the camera is IP66 rated, direct exposure to water or moisture may cause problem such as condensation. English _4 protection of cable from Water If this product is mounted outdoor, water leakage may occur at gap between cables. As shown below, butyl rubber (available on the market) shall be used to protect from water. 1. Connect power supply and BNC power source. 2. Cover black sheath of the cable (Zone A), and ensure half of butyl rubber can cover the cable joint. J ` Poor water protection at the cable sheath may cause water leakage. Make sure to wrap tightly.
` The water-proof butyl rubber is made of rubber that expands to twice the original length.
` If you do not use cable joint, it must be covered with water-proof tape. connecting the nVr Use a 12V 0.5A power adpator to power each wireless camera. There is no need to connect cameras to NVR as it is wireless AIO. 12V HDMI VGA WAN CAUTION RISK OF ELECTRI SHOCK CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT OPEN COVERS. NO USER SERVICEABLE DO NOT OPEN PARTS INSIDE. REFER SERVICING TO QUALIFIED WARNING : TO PREVENT FIRE OR SHOCK HAZARD. DO NOT EXPOSE UNITS NOT SPECIFICALLY DESIGNED SERVICE PERSONNEL. FOR OUTDOOR USE TO RAIN OR MOISTURE. English _5 specifications camera model: snc-79440bWn Item Video Imaging Device Effective Pixels Scanning System Synchronization Horizontal Resolution Min. Illumination Camera Output Lens Focal Length Max. Aperture Ratio Angular Field of View Operational Shutter Mode Gain Control White Balance Wide Dynamic Range Contrast Enhancement Digital Noise Reduction Flickerless Day & Night IR Distance Environmental Operating Temperature / Humidity Ingress Protection Details 2M CMOS (1/2.9") 1,920(H)x1,080(v) Progressive Internal 1080P 0 Lux (IR LED ON) RJ45 3.6mm F2.1 Diagonal : 105 Auto Auto Auto D-WDR Auto 3DNR Manual(50Hz/60Hz optional) TRUE D/N, Auto 82ft(Total Darkness)/130ft(Ambient Lighting)
-30C ~ +50C (-22F ~ +122F) / Less than 90% RH Startup : -10C ~ +50C IP66 English _6 Details Item Electrical Input Voltage Power Consumption Mechanical / Package information Color / Material Dimension ( x D) Weight Accessory Printed material Bracket Screw Anchor Hex key Power Adaptor Cable (65ft ) 12V/500mA DC Adaptor 5.4W(IR LEDS ON) White / Metal 69.3 x D147.2mm (2.73" x 5.79") 0.34kg prox. Quick guide one body (assembled) 3 EA (per camera) 3 EA (per camera) 1 EA (per camera) 12V 0.5A 1 EA (per camera) 4EA 65ft power Cable English _7 Unit: mm (inch) 134.5 (5.30") 77.6 (3.06") 147.2 (5.80") 6 9.3 0
(2.7 3 ")
)
"
2 6 4
.
(
. 3 7 1 1
)
"
3 7 2
.
(
. 0 3 9 6
") 4 0.1
-
"
2 0 (0.1 3.6
-
3
") 3 4.2 (2.1 5 dimension camera 6 (0.24")
)
"
4 4 3
.
(
7 4 7 8
.
)
"
2 6 4
.
(
. 3 7 1 1 English _8 FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b or 802.11g operation of this product in the USA is firmware-limited to channels 1 through 11. Industry Canada Statement This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme la norme CNR-247 dIndustrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Industry Canada Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Dclaration dexposition aux radiations Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non con trl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Antennas Statement This radio transmitter (identify the device by certification number or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le present emetteur radio (identifier le dispositif par son numero de certification ou son numero de modele s'il fait partie du materiel de categorie II) a ete approuve par Industrie Canada pour fonctionner avec les types d'antenne enumeres ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est superieur au gain maximal indique, sont strictement interdits pour l'exploitation de l'emetteur. Antenna List No. Model Type Gain[dBi]
Impedance 1 YH2400-SMAJ-108 1.87 50
(Reversed SMA Jack type) Dipole antenna Hanwha Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products. The Eco mark represents Hanwha Techwin's devotion to creating environmentally friendly products, and indicates that the product satisfies the EU RoHS Directive. Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal. Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.) This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment. To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system. English _9 Head Office 6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, 463-400 Rep. of KOREA Tel : +82.70.7147.8753 Fax : +82.31.8018.3740 www.hanwha-security.com Hanwha Techwin America 500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666 Toll Free +1.877.213.1222 Direct +1.201.325.6920 Fax +1.201.373.0124 www.hanwha-security.com Hanwha Techwin Europe Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom Tel +44.1932.57.8100 Fax +44.1932.57.8101 www.hanwha-security.eu