all | frequencies |
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|
manual | photos |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
Revised Manual | Users Manual | 2.01 MiB | ||||
1 2 |
|
Internal Photos | Internal Photos | 341.00 KiB | May 22 2003 | |||
1 2 |
|
External Photos | External Photos | 288.89 KiB | May 22 2003 | |||
1 2 |
|
Comments | Cover Letter(s) | 38.29 KiB | May 22 2003 | |||
1 2 |
|
Description of Changes | Cover Letter(s) | 6.58 KiB | May 22 2003 | |||
1 2 |
|
RF Exposure Info Revised | RF Exposure Info | 24.21 KiB | May 22 2003 | |||
1 2 |
|
Response | Cover Letter(s) | 58.52 KiB | May 22 2003 | |||
1 2 |
|
Test Photos | Test Setup Photos | 328.18 KiB | May 22 2003 | |||
1 2 |
|
Test Report Revised | Test Report | 2.23 MiB | May 22 2003 | |||
1 2 | Cover Letter(s) | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 |
|
External Pics | External Photos | 482.82 KiB | ||||
1 2 |
|
Internal Pics | Internal Photos | 1.01 MiB | ||||
1 2 | ID Label/Location Info | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Operational Description | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | RF Exposure Info | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | Test Setup Photos | |||||||
1 2 | Test Report |
1 2 | Revised Manual | Users Manual | 2.01 MiB |
U S E R S M A N U A L T60H656 Mini-PCI Type IIIB WLAN CARD Ambit Microsystems Corporation 5F-1, 5 Hsin-An Rd., Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C. TEL: 886-3-5784975, FAX: 886-3-5782924, Internet: Ambit@shts.seed.net.tw 1 Contents SECTION ONE:
INTRODUCTION.............................................................................................1 FEATURES...............................................................................................................................1 1.1 1.1.1 WIRELESS LAN FUNCTION.....................................................................................................1 1.2:FCC NOTICE...................................................................................................................................2 1.2.1 FCC COMPLIANCE ......................................................................................................................... 1.2.2 FCC CLASS B STATEMENT .........................................................................................................2 SECTION TWO:
WIRELESS LAN INSTALLATION...............................................................3 2-1 SYSTEM REQUIREMENTS ................................................................................................................3 2-2 INSTALLATION AND UNINSTALL PROCESS.......................................................................................3 SECTION THREE:
WIRELESS UTILITY AND CONFIGURATION.....................................9 3-1 WINDOWS 98/ME/2000 WIRELESS UTILITY ...................................................................................9 SECTION FOUR: WINDOWS XP WIRELESS UTILITY AND CONFIGURATION ...........15 4-1 WINDOWS XP WIRELESS UTILITY ................................................................................................15 APPENDIX A GLOSSARY ................................................................................................................22 The information contained in this manual has been verified at the time of this manual printing. The manufacturer reserves the right to make any changes and improvements in the product described in this manual at any time and without notice. All registered trademarks are the property of their respective owners. 2 Section One:
Introduction Ambit Wireless Mini-PCI Module complied with IEEE 802.11b 11Mbps Standard, it can be used to provide a variety of low-cost wireless network interface card to connect your wireless LAN via fitting into the MiniPCI Type III slot. The Wireless MiniPCI Module that complies with this specification and combines networking with high-
speed Internet access will let people connect to the Internet anywhere, anytime. With seamless roaming, fully interoperability and advanced security with WEP standard, Wireless MiniPCI Module can allow user to switch to different vendors Access Points through the wireless networks and to prevent from eavesdropping. 1.1 Features 1.1.1 Wireless LAN Function Form Factor & Bus Interface MiniPCI Type IIIB, compliant to MiniPCI Wireless LAN Compliance IEEE 802.11b Specification Rev 1.0 Radio Technology Operating Frequency Modulation Schemes Channel Numbers WLAN Data Rate Spreading Direct Sequence Spread Spectrum 2.4 ~ 2.497GHz ISM band DQPSK, DBPSK and CCK IEEE 802.11b compliant 1 ~ 11 channels for United States 1 ~ 13 channels for Europe 1 ~ 13 or 14 channels for Japan 11, 5.5, 2, and 1Mbps 11-chip Barker Sequence Media Access Protocol CSMA/CA with ACK Transmitter Output Power Typ. 13+/-1 dBm Receiver Sensitivity Typ. 82 dBm for 11Mbps @ 8% PER Antenna Type Typ. 85 dBm for 1Mbps @ 8% PER Integrated diversity switch with Hirose compliant connectors(U-FL) for connecting dual diversity antennas 1 Operating Voltage Radio Dynamic Rate Shifting Network Architecture Operating Systems Mechanical Requirements 3.3VDC On / Off Automatic fallback Ad-hoc, Infrastructure Windows 98/Me/2000/XP Mini-PCI Type IIIB dimension. 1.2:FCC Notice 1.2.1 FCC Class B Statement This equipment has been tasted and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on , the user is encouraged to try to correct the interferencr by one or more of the following measures:
! Reorient or relocate the receiving antenna
!
! Connect the equipment into an outlet on a circuit different from that to which the receiver is increase the separation between the equipment and the receiver connected
! Consult the dealer or an experienced radio/TV technician for help IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as the 2 conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). The OEM integrator is required to label their end product using this module by the warning statement such as This product integrate an RF module with FCC ID: MCLT60H656. The OEM integrator is not allowed to use the antenna which is not included in this authorization. Also the warning statement of the use of the antenna which is not approved in this authorization should be also included in the users manual of the end product. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and Obtaining a separate FCC authorization. 2 Caution: For your health sake, please keep at least 20 cm away from your Notebook LCD Panel while using wireless LAN. 3 Section Two: Wireless Lan Installation 2-1 System Requirements In order to install Wireless LAN driver and Utility and use the Wireless LAN card in your notebook computer. Your notebook system must meet the following requirements:
! Ambit Mini-PCI Wireless LAN Card already inserted
! Windows 98SE,2K,ME,XP OS Support 2-2 Installation and Uninstall Process Install Wireless LAN (Windows 98/2K/ME/XP) 1. While power on and open Windows OS at first time, the OS will detect Wireless LAN Card exist and pop up the following dialogue. If you dont want to perform install process now, then press Cancel bottom. If you want to install now, please wait a moment then you can see the next InstallShield Wizard dialogue pop up. If you press Cancel Bottom at the above dialogue, but you want to start install process later. Execute the program Setup.exe in the CD. Windows displays the dialog as below. Press Next button to continue. 4 2. It displays a License Agreement dialog. Press Next to continue. 5 3. Select the destination folder that you want to place the files. 4. Wait for the install program to do the installation. 6 5. Congratulations! Wireless LAN has been installed successfully. Please click Finish to go to the next step. 6. Please remove any disks from any drives before your click Finish. Then click Finish to complete setup. 7 Uninstall Wireless LAN (Windows 98/2K/ME/XP) 1. One can remove the Wireless LAN via the Add/Remove Programs in the Control Panel. Select Wireless LAN and click Add/Remove button, the dialog as below displays. 2. Select Remove and then click the Next button to perform the un-installation. Click OK button if you really want to remove the Wireless LAN. 8 3. Wait for the un-installation to do its work. 4. Click Finish to complete the un-Installation. 9 Section Three:
Wireless Utility and Configuration The following sections describe the Wireless Network Configuration Utility. This utility provides quick access and friendly interface to configure the card setup. 3-1 Windows 98/ME/2000 Wireless Utility After installation is completed, a Wireless LAN Utility icon will appear in Desktop screen. Click it, then you will see the screen below. If you cannot find the icon, you can select Start ->Program->Wireless LAN Configuration Utility Icon. Card Status You can see the AP information that your card connected. In this page you also can find Firmware Version , MAC Address and Frequency Domain. ESSID: An acronym for Extended Service Set Identifier, ESSID is the unique name shared among all clients and Access Points in a wireless network. The ESSID must be 10 identical for all clients or Access Points participating in the same network. The ESSID is case sensitive and must not exceed 32 characters. Press Rescan it will scan the specific ESSID that your profile set. If your profile set the ESSID to be ANY, then while you press Rescan, it will scan AP in the nearby area and choose the stronger one. From Link Quality and Signal Strength, you can tell the wireless transmission quality. 11 Profile If you want to use default Profile setting, then choose the DEFAULT at profile name. If you want to setup your own profile, then select PROFILE1 and you can change this PROFILE1 name to the one you like. There are two network types:
Ad-Hoc: This mode is used for a simple peer-to-peer network. It offers file sharing between wireless clients without a wireless Access Point (AP). Infrastructure: This mode allows a wireless LAN to be integrated into an existing wired network through an AP. Infrastructure type networks also permit roaming between Access Points while maintaining connection to all network resources. Infrastructure mode provides additional features, such as WEP security, power saving and extended range. ESSID: You can either choose specific AP or connect to any AP in the nearby area. Power Save: enable it, so it will be triggered when your computer system is inactive. 12 WEP Key: Wired Equivalent Privacy, WEP is an encryption scheme used to protect your wireless data communications. WEP uses a combination of 40-bit keys,128-bit keys to provide data encryption for your wireless network. AP and wireless card should use the same WEP key in order to communication. KEY Format: You can choose to enter ASCII Characters (0~9, a~z, A~Z) or Hexadecimal number (0~9, a~f, A~F) Default Key: The current KEY you choose. KEY1~4: If you choose 40-bit keys, then you must enter 5 ASCII Characters or 10 Hexadecimal numbers. If you choose 128-bit keys, then you must enter 13 ASCII Characters or 26 Hexadecimal numbers. 13 Site Survey Use the Site Survey Tool. You can identify each channel transmission quality. 14 About Use the About, you can see the information of Network Driver, Configuration Utility and Firmware Version. 15 Section Four: Windows XP Wireless Utility and Configuration 4-1 Windows XP Wireless Utility 1. To configure the wireless card setting, you can select Start\Settings\Network Connection in the Windows XP. Choose the wireless network connection, then you will see below screen. From this screen, you can see wireless connection status and wireless signal level. 2. Select Properties in the above screen. The following windows will show up. 16 In General page, Wireless LAN card information and networking protocol have been displayed. Extra networking protocol can be installed in this page. 17 3. Select Wireless Networks page, you can see available wireless networks in your nearby area. You can add your preferred wireless Access Point to your list, so your wireless card will search for specific wireless networks. Configure To connect to an existing access point (infrastructure) network, under Available networks, click the network name, and then click Configure to setup wireless security and data encryption. Reflesh To update the list of available networks that are within range of your computer, click Refresh. Add To connect to an access point (infrastructure) network that you know is available but that does not appear under Available networks, under Preferred networks, click Add. In Wireless Network Properties, specify the network name (Service Set Identifier). 18 Remove To remove a wireless network from the list of preferred networks. Advanced
*If your network are configuring to a computer-to-computer (ad hoc) network, select Computer-to-computer (ad hoc) network only.
*If you want to connect to a computer-to-computer and access point (infrastructure) networks are within range of your computer, click Access point
(infrastructure)network only.
*If you want to connect to a computer-to-computer (ad hoc) network and both computer-to-computer and access point (infrastructure) networks are within range of your computer, click Any available network (access point preferred). To automatically connect to available networks that do not appear in the Preferred networks list, click Advanced, and then select the Automatically connect to non-
preferred networks check box. 19 Define your network name (SSID) in the following windows, so your can join a specific wireless network. Check AP has WEP on or not. You wireless network will need to have same WEP setting with AP in order to communicate. If your wireless network dont have any AP, check the This is computer-to computer (ad-hoc) network; wireless access points are not used 20 This window provides authentication via 802.1X. 802.1X, an IEEE standard that provides an authentication framework for 802-based LANs. 802.1X takes advantage of an existing authentication protocol known as the Extensible Authentication Protocol. 802.1x, giving someone secure, encrypted, wireless access on a Microsoft network will be as easy as setting a flag on the users domain account. What does this mean for the Home Network user?
802.1x will ensure that if and when you make the change over to Wireless Ethernet, your neighbor will not be able to access your wireless LAN!
21 The Advanced window offers Firewall and Internet Connection Sharing functions. Depends on your networking environment, you can select below functions. 22 Appendix A Glossary Access Point - An internetworking device that seamlessly connects wired and wireless networks together. Ad-Hoc - Ad-Hoc is a peer- to-peer wireless network without Access Point. A group of wireless clients consistent an independent wireless LAN. Backbone - The core infrastructure of a network, the portion of the network that transports information from one central location to another central location. The information is then off-loaded onto a local system. BSS - Stands for Basic Service Set. An Access Point associated with several wireless stations. ESS - Stands for Extended Service Set. More than one BSS can be configured as an Extended Service Set. An ESS is basically a roaming domain. Ethernet - A popular local area data communications network, originally developed by Xerox Corp., which accepts transmission from computers and terminals. Ethernet operates on 10/100 Mbps transmission rate over shielded coaxial cable or over shielded twisted pair telephone wire. Infrastructure - An integrated wireless and wired LAN is called an Infrastructure configuration. MINI-PCI TYPE III - Personal Computer Memory Card International Association, which develops standards for PC cards, formerly known as MINI-PCI TYPE III cards, are available in three types which are about the same length and width as credit cards, but range in thickness from 3.3 mm (Type I) to 5.0 mm (Type II) to 10.5 mm
(Type III). These cards can be used for many functions, including memory storage, as landline modems and as wireless LAN. Roaming - A function that allows one to travel with a mobile end system (wireless LAN mobile station, for example) through the territory of a domain (an ESS, for example) while continuously connecting to the infrastructure. 23
1 2 | Internal Photos | Internal Photos | 341.00 KiB | May 22 2003 |
CONSTRUCTION PHOTOS OF EUT Page 1 Page 2
1 2 | External Photos | External Photos | 288.89 KiB | May 22 2003 |
CONSTRUCTION PHOTOS OF EUT Page 1 Page 2
1 2 | Comments | Cover Letter(s) | 38.29 KiB | May 22 2003 |
American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 May 20, 2003 RE:
Ambit Microsystems Corporation FCC ID:
MCLT60H656 I have a few comments on the above referenced Application. 1) For permissive change applications, the conducted power is expected to be within 0.5 dB of the original conducted power. It appears that the conducted power in this application is 1.0 dBm below the original power. Please recheck the power measurements, software settings, etc. to ensure proper output levels. If necessary, please retest the spurious emissions. 2) Please adjust the RF exposure exhibit to match the power measured in 1). Timothy R. Johnson Examining Engineer mailto: tjohnson@AmericanTCB.com The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.
1 2 | Description of Changes | Cover Letter(s) | 6.58 KiB | May 22 2003 |
FCC ID: MCLT60H656 Description of Permissive Change This report is prepared for FCC class II permissive change. The difference compared with the original design is the EUT add one new antenna. ADT No.911122R04B Report No.920430R04
1 2 | RF Exposure Info Revised | RF Exposure Info | 24.21 KiB | May 22 2003 |
FCC ID: MCLT60H656 RF EXPOSURE REPORT REPORT NO.: RF911122R04B MODEL NO.: T60H656 ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT: AMBIT Microsystems Corporation ADDRESS: 4-1,Ming-Sheng ST., Tu-Cheng Industrial Area, Tu-Cheng City, Taipei,Taiwan R.O.C. ISSUED BY: Advance Data Technology Corporation LAB LOCATION: No. 81-1, Lu Liao Keng, 9 Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien, Taiwan, R.O.C. Lab Code: 200376-0 Report No.: 911122R04B ADT No.: 920430R04 FCC ID: MCLT60H656 RF Exposure Measurement 1. Introduction In this document, we try to prove the safety of radiation harmfulness to the human body for our product. The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The Gain of the antenna used in this product is measured in a Fully Anechoic Chamber (FAC) calibrated for antenna measurement in ADT, and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis transmission formula is a far field assumption, the calculated result of that is an over-prediction for near field power density. We will take that as the worst case to specify the safety range. 2. RF Exposure Limit According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range
(MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density Average Time
(mW/cm2)
(minutes)
(A)Limits For Occupational / Control Exposures 300-1500 1500-100,000 F/300 5
(B)Limits For General Population / Uncontrolled Exposure 300-1500 1500-100,000 F = Frequency in MHz F/1500 1.0 6 6 6 30 Report No.: 911122R04B ADT No.: 920430R04 FCC ID: MCLT60H656 3. Friis Formula Friis transmission formula : Pd = (Pout*G) / (4*pi*r2) where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd is the limit of MPE, 1 mW/cm2. If we know the maximum Gain of the antenna and the total power input to the antenna, through the calculation, we will know the MPE value at distance 20cm. Ref. : David K. Cheng, Field and Wave Electromagnetics, Second Edition, Page 640, Eq. (11-133). 4 EUT Operating condition The software provided by Manufacturer enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. 5 Climate Condition The temperature and related humidity: 20 deg. C and 63 % RH 6. Classification This device is not fixed inside the host equipment, it is connected with host through wire. So it is easy to be re-located in the place where at least 20 cm far away from the body of the user. Warning statement to the user for keeping at least 20cm or more separation distance with the antenna should be included in users manual. So, this device is classified as Mobile Device. Report No.: 911122R04B ADT No.: 920430R04 FCC ID: MCLT60H656 7 Test Results 7.1 Antenna Gain The maximum Gain measured in Fully Anechoic Chamber is 1.8dBi or 1.514 (numeric). 7.2 Output Power Into Antenna & RF Exposure value at distance 20cm:
Output Power to Antenna (mW) Power Density
(mW/cm2) Limit of Power Density
(mW/cm2) 13.804 14.125 14.125 0.004157 0.004253 0.004253 1.0 1.0 1.0 Channel 1 6 11 Channel Frequency
(MHz) 2412 2437 2462 Report No.: 911122R04B ADT No.: 920430R04
1 2 | Response | Cover Letter(s) | 58.52 KiB | May 22 2003 |
Subject: Review of AMBIT MICROSYSTEMS CORPORATION Application FCC ID:
MCLT60H656 Permissive Change To: tjohnson@AmericanTCB.com, whgraff@qwest.net Cc: alan_lane@adt.com.tw, bruce_shiau@adt.com.tw, eric@adt.com.tw, jtchen@adt.com.tw, Hi, For your question in attached comment:
1)& 2) Done "again"! The revised test report (-revised2)& RF exposure report (-revised2) has been submitted to you. Waitting for the grant! It's urgent now! Our client wants to receive the grant as soon as possible!
Your earliest response of this matter would be greatly appreciated!
Best Regards, Amanda Chu / (Embedded image moved to file: pic26386.gif)
~~~~~~~~~~~~~~~~~~~~~~~~~
Certification Specialist ADT Corp. (Hsin Chu Office) TEL: 03-5935343 ext. 1737 FAX: 03-5935342
~~~~~~~~~~~~~~~~~~~~~~~~~
----- e Eric Lin/ADT 2003/05/21 11:01 AM -----
"Timothy R. Johnson" HG eric_lin@adt.com.tw
<tjohnson@America eG Alan_Lane@mail.adt.com.tw nTCB.com> DG Review of AMBIT MICROSYSTEMS CORPORATION Application FCC ID: MCLT60H656 Permissive Change 2003/05/20 12:37 PM Alan, file://C:\DOCUME~1\TIMOTH~1.JOH\LOCALS~1\Temp\eud25.htm 5/22/2003 Attached are comments regarding review of this application. Please provide a response as soon as possible. Thank You, Timothy R. Johnson NARTE Certified EMC Engineer No. EMC-002205-NE email: tjohnson@AmericanTCB.com alternate email: TRJ@adelphia.net
(See attached file: ATCB Comment_ 051903.pdf) pic26386.gif
=big5BQVRDQiBDb21tZW50XyAwNTE5MDMucGRm=2.pdf file://C:\DOCUME~1\TIMOTH~1.JOH\LOCALS~1\Temp\eud25.htm 5/22/2003
1 2 | Test Photos | Test Setup Photos | 328.18 KiB | May 22 2003 |
FCC ID: MCLT60H656 5 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: RF911122R04B ADT No.: 920430R04 46 Issued: May 14, 2003 FCC ID: MCLT60H656 Report No.: RF911122R04B ADT No.: 920430R04 47 Issued: May 14, 2003 FCC ID: MCLT60H656 RADIATED EMISSION TEST Report No.: RF911122R04B ADT No.: 920430R04 48 Issued: May 14, 2003 FCC ID: MCLT60H656 Report No.: RF911122R04B ADT No.: 920430R04 49 Issued: May 14, 2003
1 2 | Test Report Revised | Test Report | 2.23 MiB | May 22 2003 |
FCC ID: MCLT60H656 FCC TEST REPORT REPORT NO.: RF911122R04B MODEL NO.: T60H656 RECEIVED: Apr. 30, 2003 TESTED: Apr. 30 to May 21, 2003 APPLICANT: AMBIT Microsystems Corporation ADDRESS: 4-1,Ming-Sheng ST., Tu-Cheng Industrial Area, Tu-Cheng City, Taipei,Taiwan R.O.C. ISSUED BY: Advance Data Technology Corporation LAB LOCATION: No. 81-1, Lu Liao Keng, 9 Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien, Taiwan, R.O.C. This test report consists of 50 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, NVLAP or any government agencies. The test results in the report only apply to the tested sample. Lab Code: 200376-0 Report No.: RF911122R04B ADT No.: 920430R04 1 Issued: May 14, 2003 FCC ID: MCLT60H656 Table of Contents CERTIFICATION.......................................................................................................4 SUMMARY OF TEST RESULTS............................................................................5 GENERAL INFORMATION .....................................................................................6 GENERAL DESCRIPTION OF EUT......................................................................6 DESCRIPTION OF TEST MODES........................................................................7 GENERAL DESCRIPTION OF APPLIED STANDARDS ...................................7 DESCRIPTION OF SUPPORT UNITS..................................................................8 TEST TYPES AND RESULTS ................................................................................9 CONDUCTED EMISSION MEASUREMENT.......................................................9 TEST INSTRUMENTS.............................................................................................9 TEST PROCEDURES ...........................................................................................10 DEVIATION FROM TEST STANDARD...............................................................10 TEST SETUP ..........................................................................................................11 EUT OPERATING CONDITIONS ........................................................................11 TEST RESULTS......................................................................................................12 RADIATED EMISSION MEASUREMENT ..........................................................18 LIMITS OF RADIATED EMISSION MEASUREMENT......................................18 TEST INSTRUMENTS...........................................................................................19 TEST PROCEDURES ...........................................................................................20 DEVIATION FROM TEST STANDARD...............................................................20 TEST SETUP ..........................................................................................................21 EUT OPERATING CONDITIONS ........................................................................21 TEST RESULTS......................................................................................................22 6dB BANDWIDTH MEASUREMENT ..................................................................26 LIMITS OF 6dB BANDWIDTH MEASUREMENT..............................................26 TEST INSTRUMENTS...........................................................................................26 TEST PROCEDURE ..............................................................................................27 DEVIATION FROM TEST STANDARD...............................................................27 TEST SETUP ..........................................................................................................27 EUT OPERATING CONDITIONS ........................................................................27 TEST RESULTS......................................................................................................28 MAXIMUM PEAK OUTPUT POWER ..................................................................32 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT .............32 TEST INSTRUMENTS...........................................................................................32 TEST PROCEDURES ...........................................................................................33 1 2 3 3.1 3.2 3.3 3.4 4 4.1 4.1.1 4.1.2 4.1.3 4.1.4 4.1.5 4.1.6 4.2 4.2.1 4.2.2 4.2.3 4.2.4 4.2.5 4.2.6 4.2.7 4.3 4.3.1 4.3.2 4.3.3 4.3.4 4.3.5 4.3.6 4.3.7 4.4 4.4.1 4.4.2 4.4.3 Report No.: RF911122R04B ADT No.: 920430R04 2 Issued: May 14, 2003 FCC ID: MCLT60H656 4.4.4 4.4.5 4.4.6 4.4.7 4.5 4.5.1 4.5.2 4.5.3 4.5.4 4.5.5 4.5.6 4.5.7 4.6 4.6.1 4.6.2 4.6.3 4.6.4 4.6.5 4.6.6 4.7 4.7.1 4.7.2 5 6 DEVIATION FROM TEST STANDARD...............................................................33 TEST SETUP ..........................................................................................................33 EUT OPERATING CONDITIONS ........................................................................33 TEST RESULTS......................................................................................................34 POWER SPECTRAL DENSITY MEASUREMENT ...........................................35 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT.......................35 TEST INSTRUMENTS...........................................................................................35 TEST PROCEDURE ..............................................................................................36 DEVIATION FROM TEST STANDARD...............................................................36 TEST SETUP ..........................................................................................................36 EUT OPERATING CONDITIONS ........................................................................36 TEST RESULTS......................................................................................................37 BAND EDGES MEASUREMENT.........................................................................41 LIMITS OF BAND EDGES MEASUREMENT....................................................41 TEST INSTRUMENTS...........................................................................................41 TEST PROCEDURE ..............................................................................................41 DEVIATION FROM TEST STANDARD...............................................................41 EUT OPERATING CONDITION...........................................................................42 TEST RESULTS......................................................................................................42 ANTENNA REQUIREMENT..................................................................................45 STANDARD APPLICABLE....................................................................................45 ANTENNA CONNECTED CONSTRUCTION ....................................................45 PHOTOGRAPHS OF THE TEST CONFIGURATION.......................................46 INFORMATION ON THE TESTING LABORATORIES.....................................50 Report No.: RF911122R04B ADT No.: 920430R04 3 Issued: May 14, 2003 FCC ID: MCLT60H656 1 CERTIFICATION PRODUCT :
BRAND NAME :
MODEL NO. :
APPLICANT :
STANDARDS :
802.11b Wireless LAN MiniPCI Card AMBIT T60H656 AMBIT Microsystems Corporation 47 CFR Part 15, Subpart C (Section 15.247), ANSI C63.4-1992 We, Advance Data Technology Corporation, hereby certify that one sample of the designation has been tested in our facility from Apr. 30 to May 21, 2003. The test record, data evaluation and Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample's EMC characteristics under the conditions herein specified. CHECKED BY:
, DATE:
May 14, 2003
( Amanda Chu ) APPROVED BY:
, DATE:
May 14, 2003
( Eric Lin, Manager ) Report No.: RF911122R04B ADT No.: 920430R04 4 Issued: May 14, 2003 FCC ID: MCLT60H656 2 SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications:
APPLIED STANDARD: 47 CFR Part 15, Subpart C Standard Section Test Type and Limit Result REMARK 15.207 AC Power Conducted Emission PASS 15.247(a)(2) Spectrum Bandwidth of a Direct Sequence Spread Spectrum System Limit: min. 500kHz 15.247(b) Maximum Peak Output Power Limit: max. 30dBm 15.247(c) Transmitter Radiated Emissions Limit: Table 15.209 15.247(d) 15.247(c) Power Spectral Density Limit: max. 8dBm Band Edge Measurement Limit: 20 dB less than the peak value of fundamental frequency Meet the requirement of limit Minimum passing margin is 22.60dBuV at 0.166 MHz PASS Meet the requirement of limit PASS Meet the requirement of limit Meet the requirement of limit Minimum passing margin is 1.1dBuV at 4874.00 MHz PASS PASS Meet the requirement of limit PASS Meet the requirement of limit Report No.: RF911122R04B ADT No.: 920430R04 5 Issued: May 14, 2003 FCC ID: MCLT60H656 3 GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT PRODUCT MODEL NO. POWER SUPPLY MODULATION TYPE RADIO TECHNOLOGY TRANSFER RATE FREQUENCY RANGE NUMBER OF CHANNEL OUTPUT POWER ANTENNA TYPE DATA CABLE I/O PORTS ASSOCIATED DEVICES 802.11b Wireless LAN MiniPCI Card T60H656 3.3VDC from host equipment CCK, DBPSK, DQPSK DSSS 1/2/5.5/11Mbps 2412MHz ~ 2462MHz 11 11.5dBm Inverted-F antenna NA NA NA NOTE:
1. This report is prepared for Class II permissive change. The difference compared with the original design is as the following:
u Add one new antenna:
Antenna Type Gain (dBi) Inverted-F
+1.8 2. For a more detailed features description, please refer to the manufacturer's specifications or User's Manual. Report No.: RF911122R04B ADT No.: 920430R04 6 Issued: May 14, 2003 FCC ID: MCLT60H656 3.2 DESCRIPTION OF TEST MODES Eleven channels are provided in this EUT. Channel 1 2 3 4 5 6 NOTE:
Frequency 2412 MHz 2417 MHz 2422 MHz 2427 MHz 2432 MHz 2437 MHz Channel 7 8 9 10 11 Frequency 2442 MHz 2447 MHz 2452 MHz 2457 MHz 2462 MHz 1. Below 1 GHz, the channel 1, 6, and 11 were pre-tested in chamber. The channel 11, worst case one, was chosen for final test. 2. Above 1 GHz, the channel 1, 6, and 11 were tested individually. 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is a 802.11b Wireless LAN MiniPCI Card. According to the specifications of the manufacturer, it must comply with the requirements of the following standards:
FCC CFR 47 Part 15, Subpart C. (15.247) ANSI C63.4 : 1992 All tests have been performed and recorded as per the above standards. NOTE: The EUT is also considered as a kind of computer peripheral, because the connection to computer is necessary for typical use. It has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. Report No.: RF911122R04B ADT No.: 920430R04 7 Issued: May 14, 2003 FCC ID: MCLT60H656 3.4 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. No. Product 1 NOTEBOOK COMPUTER 2 PRINTER Brand ACER Model No. BY27 Serial No. NA FCC ID NA EPSON LQ-300+
DCGY017079 FCC DoC No. Signal cable description 1 NA 2 1.8m braid shielded wire, terminated with DB25 and Centronics connector via metallic frame, w/o core NOTE: All power cords of the above support units are unshielded (1.8m). 600 ohm TEL Line (1.8m) EUT 1. NOTEBOOK 2. PRINTER TEST TABLE Report No.: RF911122R04B ADT No.: 920430R04 8 Issued: May 14, 2003 FCC ID: MCLT60H656 4 TEST TYPES AND RESULTS 4.1 CONDUCTED EMISSION MEASUREMENT FREQUENCY OF EMISSION (MHz) CONDUCTED LIMIT (dBV) 0.15-0.5 0.5-5 5-30 Quasi-peak 66 to 56 56 60 Average 56 to 46 46 50 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. 3. All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above. 4.1.1 TEST INSTRUMENTS DESCRIPTION &
MANUFACTURER ROHDE & SCHWARZ Test Receiver ROHDE & SCHWARZ LISN
(for EUT) KYORITSU LISN (for peripheral) RF Cable (JETBAO) Terminator(for KYORITSU) Software MODEL NO. SERIAL NO. ESCS 30 847124/029 CALIBRATED UNTIL Nov. 17, 2003 ESHS-Z5 848773/004 Nov. 13, 2003 KNW-407 RG233/U 50 Cond-V2e 8/1395/12 Cable_CA_01
#1 NA Jul. 23, 2003 Jul. 03, 2003 Apr. 11, 2004 NA NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in ADT Shielded Room No. A. 3. The VCCI Con A Registration No. is C-817. Report No.: RF911122R04B ADT No.: 920430R04 9 Issued: May 14, 2003 FCC ID: MCLT60H656 TEST PROCEDURES 4.1.2 a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150 kHz to 30 MHz was searched. Emission levels over 10dB under the prescribed limits could not be reported 4.1.3 DEVIATION FROM TEST STANDARD No deviation Report No.: RF911122R04B ADT No.: 920430R04 10 Issued: May 14, 2003 FCC ID: MCLT60H656 TEST SETUP 4.1.4 For the actual test configuration, please refer to the related item Photographs of the Test Configuration. 4.1.5 EUT OPERATING CONDITIONS a. Plug the EUT into the PCI extender which connected to a computer system placed on a testing table. b. The computer system ran a test program to enable EUT under transmission/receiving condition continuously at specific channel frequency. c. The computer system sent "H" messages to its screen. d. The computer system sent "H" messages to printer, and the printer prints them on paper. Report No.: RF911122R04B ADT No.: 920430R04 11 Issued: May 14, 2003 FCC ID: MCLT60H656 4.1.6 TEST RESULTS EUT MODE INPUT POWER
(SYSTEM) 802.11b Wireless LAN MiniPCI Card Channel 1 MODEL T60H656 6dB BANDWIDTH 9 kHz 120Vac, 60 Hz PHASE Line (L) ENVIRONMENTAL CONDITIONS 26 deg. C, 64%RH, 978 hPa TESTED BY Eric Lee No 1 2 3 4 5 6 Freq.
[MHz]
0.177 0.232 0.279 0.334 12.566 21.391 Corr. Factor
(dB) 0.10 0.10 0.10 0.10 0.70 1.06 Reading Value Emission Level Limit
[dB (uV)]
AV.
-
-
-
-
-
-
Q.P. 36.94 32.08 36.09 34.44 31.62 27.36
[dB (uV)]
AV.
-
-
-
-
-
-
Q.P. 37.04 32.18 36.19 34.54 32.32 28.42
[dB (uV)]
AV. 54.61 52.38 50.85 49.36 50.00 50.00 Q.P. 64.61 62.38 60.85 59.36 60.00 60.00 Margin
(dB) Q.P.
-27.57
-30.20
-24.66
-24.82
-27.68
-31.58 AV.
-
-
-
-
-
-
NOTES: (1) "*": Undetectable
(2) Q.P. and AV. are abbreviations of quasi-peak and average.
(3) "-": The Quasi-peak reading value also meets an average limit, thus measurement with the average detector is unnecessary.
(4) The emission levels of other frequencies were very low against the limit.
(5) Correction Factor = Insertion loss + Cable loss
(6) Margin value = Emission level - Limit value Report No.: RF911122R04B ADT No.: 920430R04 12 Issued: May 14, 2003 FCC ID: MCLT60H656 EUT MODE INPUT POWER
(SYSTEM) 802.11b Wireless LAN MiniPCI Card Channel 1 MODEL T60H656 6dB BANDWIDTH 9 kHz 120Vac, 60 Hz PHASE Neutral (N) ENVIRONMENTAL CONDITIONS 26 deg. C, 64%RH, 978 hPa TESTED BY Eric Lee No 1 2 3 4 5 6 Freq.
[MHz]
0.177 0.236 0.279 0.334 1.502 12.289 Corr. Factor
(dB) 0.10 0.10 0.10 0.10 0.10 0.55 Reading Value Emission Level Limit
[dB (uV)]
AV.
-
-
-
-
-
-
Q.P. 34.98 32.90 36.38 34.83 15.48 32.65
[dB (uV)]
AV.
-
-
-
-
-
-
Q.P. 35.08 33.00 36.48 34.93 15.58 33.20
[dB (uV)]
AV. 54.61 52.24 50.85 49.36 46.00 50.00 Q.P. 64.61 62.24 60.85 59.36 56.00 60.00 Margin
(dB) Q.P.
-29.53
-29.24
-24.37
-24.43
-40.42
-26.80 AV.
-
-
-
-
-
-
NOTES: (1) "*": Undetectable
(2) Q.P. and AV. are abbreviations of quasi-peak and average.
(3) "-": The Quasi-peak reading value also meets an average limit, thus measurement with the average detector is unnecessary.
(4) The emission levels of other frequencies were very low against the limit.
(5) Correction Factor = Insertion loss + Cable loss
(6) Margin value = Emission level - Limit value Report No.: RF911122R04B ADT No.: 920430R04 13 Issued: May 14, 2003 FCC ID: MCLT60H656 EUT MODE INPUT POWER
(SYSTEM) 802.11b Wireless LAN MiniPCI Card Channel 6 MODEL T60H656 6dB BANDWIDTH 9 kHz 120Vac, 60 Hz PHASE Line (L) ENVIRONMENTAL CONDITIONS 26 deg. C, 64%RH, 978 hPa TESTED BY Eric Lee No 1 2 3 4 5 6 Freq.
[MHz]
0.166 0.224 0.279 0.658 7.770 12.527 Corr. Factor
(dB) 0.10 0.10 0.10 0.10 0.51 0.70 Reading Value Emission Level Limit
[dB (uV)]
AV.
-
-
-
-
-
-
Q.P. 42.48 31.66 26.38 25.78 17.22 27.36
[dB (uV)]
AV.
-
-
-
-
-
-
Q.P. 42.58 31.76 26.48 25.88 17.73 28.06
[dB (uV)]
AV. 55.18 52.66 50.85 46.00 50.00 50.00 Q.P. 65.18 62.66 60.85 56.00 60.00 60.00 Margin
(dB) Q.P.
-22.60
-30.90
-34.37
-30.12
-42.27
-31.94 AV.
-
-
-
-
-
-
NOTES: (1) "*": Undetectable
(2) Q.P. and AV. are abbreviations of quasi-peak and average.
(3) "-": The Quasi-peak reading value also meets an average limit, thus measurement with the average detector is unnecessary.
(4) The emission levels of other frequencies were very low against the limit.
(5) Correction Factor = Insertion loss + Cable loss
(6) Margin value = Emission level - Limit value Report No.: RF911122R04B ADT No.: 920430R04 14 Issued: May 14, 2003 FCC ID: MCLT60H656 EUT MODE INPUT POWER
(SYSTEM) 802.11b Wireless LAN MiniPCI Card Channel 6 MODEL T60H656 6dB BANDWIDTH 9 kHz 120Vac, 60 Hz PHASE Neutral (N) ENVIRONMENTAL CONDITIONS 26 deg. C, 64%RH, 978 hPa TESTED BY Eric Lee No 1 2 3 4 5 6 Freq.
[MHz]
0.177 0.221 0.281 0.334 12.504 20.655 Corr. Factor
(dB) 0.10 0.10 0.10 0.10 0.55 0.73 Reading Value Emission Level Limit
[dB (uV)]
AV.
-
-
-
-
-
-
Q.P. 37.38 36.71 35.99 34.72 32.44 28.95
[dB (uV)]
AV.
-
-
-
-
-
-
Q.P. 37.48 36.81 36.09 34.82 32.99 29.68
[dB (uV)]
AV. 54.61 52.77 50.79 49.36 50.00 50.00 Q.P. 64.61 62.77 60.79 59.36 60.00 60.00 Margin
(dB) Q.P.
-27.13
-25.96
-24.70
-24.54
-27.01
-30.32 AV.
-
-
-
-
-
-
NOTES: (1) "*": Undetectable
(2) Q.P. and AV. are abbreviations of quasi-peak and average.
(3) "-": The Quasi-peak reading value also meets an average limit, thus measurement with the average detector is unnecessary.
(4) The emission levels of other frequencies were very low against the limit.
(5) Correction Factor = Insertion loss + Cable loss
(6) Margin value = Emission level - Limit value Report No.: RF911122R04B ADT No.: 920430R04 15 Issued: May 14, 2003 FCC ID: MCLT60H656 EUT MODE INPUT POWER
(SYSTEM) 802.11b Wireless LAN MiniPCI Card Channel 11 MODEL T60H656 6dB BANDWIDTH 9 kHz 120Vac, 60 Hz PHASE Line (L) ENVIRONMENTAL CONDITIONS 26 deg. C, 64%RH, 978 hPa TESTED BY Eric Lee No 1 2 3 4 5 6 Freq.
[MHz]
0.177 0.232 0.279 0.334 12.566 21.391 Corr. Factor
(dB) 0.10 0.10 0.10 0.10 0.70 1.06 Reading Value Emission Level Limit
[dB (uV)]
AV.
-
-
-
-
-
-
Q.P. 36.37 33.14 36.01 34.36 29.83 25.76
[dB (uV)]
AV.
-
-
-
-
-
-
Q.P. 36.47 33.24 36.11 34.46 30.53 26.82
[dB (uV)]
AV. 54.61 52.38 50.85 49.36 50.00 50.00 Q.P. 64.61 62.38 60.85 59.36 60.00 60.00 Margin
(dB) Q.P.
-28.14
-29.14
-24.74
-24.90
-29.47
-33.18 AV.
-
-
-
-
-
-
NOTES: (1) "*": Undetectable
(2) Q.P. and AV. are abbreviations of quasi-peak and average.
(3) "-": The Quasi-peak reading value also meets an average limit, thus measurement with the average detector is unnecessary.
(4) The emission levels of other frequencies were very low against the limit.
(5) Correction Factor = Insertion loss + Cable loss
(6) Margin value = Emission level - Limit value Report No.: RF911122R04B ADT No.: 920430R04 16 Issued: May 14, 2003 FCC ID: MCLT60H656 EUT MODE INPUT POWER
(SYSTEM) 802.11b Wireless LAN MiniPCI Card Channel 11 MODEL T60H656 6dB BANDWIDTH 9 kHz 120Vac, 60 Hz PHASE Neutral (N) ENVIRONMENTAL CONDITIONS 26 deg. C, 64%RH, 978 hPa TESTED BY Eric Lee No 1 2 3 4 5 6 Freq.
[MHz]
0.177 0.236 0.279 0.334 1.502 12.289 Corr. Factor
(dB) 0.10 0.10 0.10 0.10 0.10 0.55 Reading Value Emission Level Limit
[dB (uV)]
AV.
-
-
-
-
-
-
Q.P. 36.19 33.02 36.38 34.83 15.48 32.65
[dB (uV)]
AV.
-
-
-
-
-
-
Q.P. 36.29 33.12 36.48 34.93 15.58 33.20
[dB (uV)]
AV. 54.61 52.24 50.85 49.36 46.00 50.00 Q.P. 64.61 62.24 60.85 59.36 56.00 60.00 Margin
(dB) Q.P.
-28.32
-29.12
-24.37
-24.43
-40.42
-26.80 AV.
-
-
-
-
-
-
NOTES: (1) "*": Undetectable
(2) Q.P. and AV. are abbreviations of quasi-peak and average.
(3) "-": The Quasi-peak reading value also meets an average limit, thus measurement with the average detector is unnecessary.
(4) The emission levels of other frequencies were very low against the limit.
(5) Correction Factor = Insertion loss + Cable loss
(6) Margin value = Emission level - Limit value Report No.: RF911122R04B ADT No.: 920430R04 17 Issued: May 14, 2003 FCC ID: MCLT60H656 4.2 RADIATED EMISSION MEASUREMENT 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT Field strength limits are at the distance of 3 meters, emissions radiated outside of the specified bands, shall be according to the general radiated limits in 15.209 as following:
Frequencies
(MHz) 30-88 88-216 216-960 Above 960 dBuV/m Field Strength of Fundamental uV/m 100 150 200 500 40.0 43.5 46.0 54.0 NOTE:
1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report No.: RF911122R04B ADT No.: 920430R04 18 Issued: May 14, 2003 FCC ID: MCLT60H656 4.2.2 TEST INSTRUMENTS DESCRIPTION &
MANUFACTURER HP Spectrum Analyzer ADVANTEST Spectrum Analyzer CHASE RF Pre_Amplifier HP Pre_Amplifier ROHDE & SCHWARZ Test Receiver CHASE Broadband Antenna Schwarzbeck Horn_Antenna SCHWARZBECK Tunable Dipole Antenna SCHWARZBECK Tunable Dipole Antenna RF Switches (ARNITSU) RF CABLE (Chaintek) 1GHz-20GHz RF Cable(RICHTEC) MODEL NO. SERIAL NO. 8594ER R3271A CPA9232 8449B ESVS 10 CBL6111c BBHA9120-D1 UHAP VHAP CS-201 Ak 9515-D 9913-30M 3829U04676 85060311 1057 3008A01281 849231 /019 2730 D123 897 880 1565157 001 STCCAB-30M-
1GHz-021 NA 0203 CALIBRATED UNTIL Jul. 14, 2003 May 21, 2004 Apr. 24, 2004 June 27, 2004 Nov. 03, 2003 Jul 17, 2003 Jul. 31, 2003 Mar. 07, 2005 Mar. 07, 2005 Jul. 29, 2003 Aug, 20.2003 Nov. 5, 2003 AS60P8 AT-100 Software CHANCE MOST Antenna Tower CHANCE MOST Turn Table Note: 1. The calibration interval of the above test instruments is 12 months (36 months for Tunable Dipole Antenna)and the calibrations are traceable to NML/ROC and NIST/USA. TT-100 NA NA 0203 NA 2. * = These equipment are used for the final measurement. 3. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 4. The test was performed in ADT Open Site No. C. 5. The FCC Site Registration No. is 656396. 6. The VCCI Site Registration No. is R-1626. Report No.: RF911122R04B ADT No.: 920430R04 19 Issued: May 14, 2003 FCC ID: MCLT60H656 4.2.3 TEST PROCEDURES a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 10 meter open area test site. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10 dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10 dB margin would be re-
tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. NOTE:
1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Peak detection (PK) and Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 1 MHz for Peak detection at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 300 Hz for Average detection (AV) at frequency above 1GHz. 4.2.4 DEVIATION FROM TEST STANDARD No deviation Report No.: RF911122R04B ADT No.: 920430R04 20 Issued: May 14, 2003 FCC ID: MCLT60H656 4.2.5 TEST SETUP For the actual test configuration, please refer to the related item Photographs of the Test Configuration. 4.2.6 EUT OPERATING CONDITIONS Same as 4.1.6. Report No.: RF911122R04B ADT No.: 920430R04 21 Issued: May 14, 2003 FCC ID: MCLT60H656 4.2.7 TEST RESULTS EUT MODE INPUT POWER
(SYSTEM) ENVIRONMENTAL CONDITIONS 802.11b Wireless LAN MiniPCI Card MODEL Channel 11 120Vac, 60 Hz FREQUENCY RANGE DETECTOR FUNCTION T60H656 30-1000 MHz Quasi-Peak 26 deg. C, 58 % RH, 978 hPa TESTED BY Eric Lee ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Freq.
(MHz) 132.01 175.99 264.01 308.00 352.01 396.00 440.02 498.86 528.00 628.01 Emission Level
(dBuV/m) 33.5 QP 28.6 QP 30.1 QP 44.3 QP 40.8 QP 32.1 QP 32.0 QP 33.6 QP 30.6 QP 32.0 QP Limit
(dBuV/m) Margin
(dB) 43.50 43.50 46.00 46.00 46.00 46.00 46.00 46.00 46.00 46.00
-10.00
-14.90
-15.90
-1.70
-5.20
-13.90
-14.00
-12.40
-15.40
-14.00 Antenna Height
(m) 1.70 H 2.05 H 1.68 H 1.68 H 1.42 H 1.65 H 1.47 H 1.69 H 1.65 H 1.02 H Table Angle
(Degree) 327 205 272 266 287 241 45 65 241 111 Raw Value
(dBuV) 21.60 19.40 16.10 30.00 25.20 15.20 14.00 14.30 10.90 10.20 Correction Factor
(dB/m) 11.90 9.20 14.10 14.30 15.60 16.90 18.00 19.30 19.70 21.80 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Freq.
(MHz) 132.01 176.03 264.01 308.01 352.00 395.99 440.02 498.89 527.96 627.26 Emission Level
(dBuV/m) 27.3 QP 26.7 QP 38.3 QP 43.0 QP 36.5 QP 35.1 QP 34.1 QP 37.1 QP 32.9 QP 36.1 QP Limit
(dBuV/m) Margin
(dB) 43.50 43.50 46.00 46.00 46.00 46.00 46.00 46.00 46.00 46.00
-16.20
-16.80
-7.70
-3.00
-9.50
-10.90
-11.90
-8.90
-13.10
-9.90 Antenna Height
(m) 1.41 V 1.12 V 1.03 V 1.09 V 1.24 V 1.31 V 1.61 V 1.06 V 1.34 V 1.00 V Table Angle
(Degree) 118 200 268 271 281 136 138 249 207 331 Raw Value
(dBuV) 15.40 17.50 24.20 28.80 20.90 18.20 16.00 17.90 13.20 14.30 Correction Factor
(dB/m) 11.90 9.20 14.10 14.30 15.60 16.90 18.00 19.30 19.70 21.80 No. 1 2 3 4 5 6 7 8 9 10 No. 1 2 3 4 5 6 7 8 9 10 REMARKS:
1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level Limit value. 5. The limit value is defined as per 15.247 Report No.: RF911122R04B ADT No.: 920430R04 22 Issued: May 14, 2003 FCC ID: MCLT60H656 EUT MODE INPUT POWER
(SYSTEM) 802.11b Wireless LAN MiniPCI Card MODEL T60H656 Channel 1 120Vac, 60 Hz FREQUENCY RANGE DETECTOR FUNCTION TESTED BY Above 1000 MHz Peak(PK) Average (AV) Eric Lee ENVIRONMENTAL CONDITIONS 26 deg. C, 58 % RH, 978 hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Freq.
(MHz) 2387.00 2387.00
*2412.00
*2412.00 2496.00 4824.00 4824.00 7236.00 9648.00 Emission Level
(dBuV/m) 51.7 PK 43.7 AV 98.1 PK 90.8 AV 41.0 PK 54.8 PK 50.7 AV 45.4 PK 49.4 PK Limit
(dBuV/m) 74.00 54.00 74.00 74.00 54.00 74.00 74.00 Margin
(dB)
-22.30
-10.30
-33.00
-19.20
-3.30
-28.60
-24.60 Antenna Height
(m) 1.56 H 1.56 H 1.01 H 1.01 H 1.46 H 1.35 H 1.35 H 1.69 H 1.62 H Table Angle
(Degree) 89 89 271 271 276 302 302 57 121 Raw Value
(dBuV) 21.30 13.30 67.50 60.30 10.20 18.60 14.50 3.70 4.50 Correction Factor
(dB/m) 30.40 30.40 30.50 30.50 30.80 36.20 30.80 41.70 44.90 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Freq.
(MHz) 2387.00 2387.00
*2412.00
*2412.00 2496.00 4824.00 7236.00 9648.00 9648.00 Emission Level
(dBuV/m) 59.7 PK 49.3 AV 102.3 PK 96.6 AV 43.2 PK 50.2 PK 48.5 PK 52.1 PK 48.5 AV Limit
(dBuV/m) 74.00 54.00 74.00 74.00 74.00 74.00 54.00 Margin
(dB)
-14.30
-4.70
-30.80
-23.80
-25.50
-21.90
-5.50 Antenna Height
(m) 1.34 V 1.34 V 1.00 V 1.00 V 1.69 V 1.35 V 1.30 V 1.56 V 1.56 V Table Angle
(Degree) 349 349 298 298 57 148 360 237 237 Raw Value
(dBuV) 29.30 18.90 71.80 66.10 12.50 14.00 6.80 7.20 3.60 Correction Factor
(dB/m) 30.40 30.40 30.50 30.50 30.80 36.20 41.70 44.90 36.20 No. 1 1 2 2 3 4 4 5 6 No. 1 1 2 2 3 4 5 6 6 REMARKS:
1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level Limit value. 5. The limit value is defined as per 15.247 6. * : Fundamental frequency Report No.: RF911122R04B ADT No.: 920430R04 23 Issued: May 14, 2003 FCC ID: MCLT60H656 EUT MODE INPUT POWER
(SYSTEM) 802.11b Wireless LAN MiniPCI Card MODEL T60H656 Channel 6 120Vac, 60 Hz FREQUENCY RANGE DETECTOR FUNCTION TESTED BY Above 1000 MHz Peak(PK) Average (AV) Eric Lee ENVIRONMENTAL CONDITIONS 26 deg. C, 58 % RH, 978 hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Freq.
(MHz) 2376.00
*2437.00
*2437.00 2499.00 4874.00 4874.00 7311.00 9748.00 Emission Level
(dBuV/m) 45.4 PK 98.9 PK 92.7 AV 42.4 PK 56.0 PK 51.1 AV 45.9 PK 49.2 PK Limit
(dBuV/m) Margin
(dB) 74.00
-28.60 74.00 74.00 54.00 74.00 74.00
-31.60
-18.00
-2.90
-28.10
-24.80 Antenna Height
(m) 1.29 H 1.12 H 1.12 H 1.62 H 1.37 H 1.37 H 1.63 H 1.07 H Table Angle
(Degree) 13 167 167 349 157 157 299 246 Raw Value
(dBuV) 15.00 68.20 62.00 11.70 19.50 14.60 4.10 4.60 Correction Factor
(dB/m) 30.40 30.70 30.40 30.70 36.50 30.70 41.80 44.60 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Freq.
(MHz) 2376.00 2376.00
*2437.00
*2437.00 2499.00 4874.00 4874.00 7311.00 9748.00 9748.00 Emission Level
(dBuV/m) 52.0 PK 43.2 AV 103.0 PK 95.8 AV 49.6 PK 55.7 PK 52.9 AV 47.1 PK 56.3 PK 50.2 AV Limit
(dBuV/m) 74.00 54.00 74.00 74.00 54.00 74.00 74.00 54.00 Margin
(dB)
-22.00
-10.80
-24.40
-18.30
-1.10
-26.90
-17.70
-3.80 Antenna Height
(m) 1.24 V 1.24 V 1.02 V 1.02 V 1.05 V 1.32 V 1.32 V 1.30 V 1.08 V 1.08 V Table Angle
(Degree) 27 27 265 265 117 298 298 157 249 249 Raw Value
(dBuV) 21.60 12.80 72.30 65.10 18.90 19.20 16.40 5.30 11.70 5.60 Correction Factor
(dB/m) 30.40 30.40 30.70 30.70 30.70 36.50 30.70 41.80 44.60 36.50 No. 1 2 2 3 4 4 5 6 No. 1 1 2 2 3 4 4 5 6 6 REMARKS:
1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level Limit value. 5. The limit value is defined as per 15.247 6. * : Fundamental frequency Report No.: RF911122R04B ADT No.: 920430R04 24 Issued: May 14, 2003 FCC ID: MCLT60H656 EUT MODE INPUT POWER
(SYSTEM) 802.11b Wireless LAN MiniPCI Card MODEL T60H656 Channel 11 120Vac, 60 Hz FREQUENCY RANGE DETECTOR FUNCTION Above 1000 MHz Peak(PK) Average (AV) ENVIRONMENTAL CONDITIONS 26 deg. C, 58 % RH, 978 hPa TESTED BY Eric Lee ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Freq.
(MHz) 2359.00
*2462.00
*2462.00 2499.00 4924.00 4924.00 7386.00 9848.00 Emission Level
(dBuV/m) 41.3 PK 98.8 PK 92.2 AV 43.9 PK 54.6 PK 49.3 AV 47.0 PK 49.1 PK Limit
(dBuV/m) Margin
(dB) 74.00
-32.70 74.00 74.00 54.00 74.00 74.00
-30.10
-19.40
-4.70
-27.00
-24.90 Antenna Height
(m) 1.21 H 1.09 H 1.09 H 1.24 H 1.06 H 1.06 H 1.28 H 1.09 H Table Angle
(Degree) 54 254 254 74 357 357 311 58 Raw Value
(dBuV) 11.00 68.00 61.30 13.20 17.90 12.60 5.20 4.20 Correction Factor
(dB/m) 30.30 30.80 30.30 30.70 36.70 30.80 41.80 44.90 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Freq.
(MHz) 2359.00 2359.00
*2462.00
*2462.00 2499.00 4924.00 4924.00 7386.00 7386.00 9848.00 9848.00 Emission Level
(dBuV/m) 51.3 PK 44.1 AV 103.0 PK 97.4 AV 48.2 PK 57.0 PK 52.4 AV 51.8 PK 46.7 AV 58.6 PK 49.8 AV Limit
(dBuV/m) 74.00 54.00 74.00 74.00 54.00 74.00 54.00 74.00 54.00 Margin
(dB)
-22.70
-9.90
-25.80
-17.00
-1.60
-22.20
-7.30
-15.40
-4.20 Antenna Height
(m) 1.13 V 1.13 V 1.54 V 1.54 V 1.51 V 1.24 V 1.24 V 1.09 V 1.09 V 1.11 V 1.11 V Table Angle
(Degree) 261 261 241 241 297 55 55 269 269 154 154 Raw Value
(dBuV) 21.00 13.80 72.10 66.60 17.50 20.30 15.70 10.00 4.90 14.20 5.40 Correction Factor
(dB/m) 30.30 30.30 30.80 30.80 30.70 36.70 30.70 41.80 36.70 44.40 41.80 No. 1 2 2 3 4 4 5 6 No. 1 1 2 2 3 4 4 5 5 6 6 REMARKS:
1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level Limit value. 5. The limit value is defined as per 15.247 6. * : Fundamental frequency Report No.: RF911122R04B ADT No.: 920430R04 25 Issued: May 14, 2003 FCC ID: MCLT60H656 4.3 6dB BANDWIDTH MEASUREMENT 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT The minimum of 6dB Bandwidth Measurement is 0.5 MHz. 4.3.2 TEST INSTRUMENTS Description & Manufacturer Model No. Serial No. Calibrated Until R&S SPECTRUM ANALYZER FSEK30 100049 July 24, 2003 NOTE:
1.The measurement uncertainty is less than +/- 2.6dB, which is calculated as per the NAMAS document NIS81. 2.The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. Report No.: RF911122R04B ADT No.: 920430R04 26 Issued: May 14, 2003 FCC ID: MCLT60H656 4.3.3 TEST PROCEDURE The transmitter output was connected to the spectrum analyzer through an attenuator. The bandwidth of the fundamental frequency was measured by spectrum analyzer with 100 kHz RBW and 100 kHz VBW. The 6 dB bandwidth is defined as the total spectrum the power of which is higher than peak power minus 6 dB. 4.3.4 DEVIATION FROM TEST STANDARD No deviation 4.3.5 TEST SETUP EUT SPECTRUM ANALYZER 4.3.6 EUT OPERATING CONDITIONS The software provided by client to enable the EUT under transmission condition continuously at lowest, middle and highest channel frequencies individually. Report No.: RF911122R04B ADT No.: 920430R04 27 Issued: May 14, 2003 FCC ID: MCLT60H656 4.3.7 TEST RESULTS EUT 802.11b Wireless LAN MiniPCI Card MODEL T60H656 INPUT POWER
(SYSTEM) 120Vac, 60 Hz TESTED BY Eric Lee ENVIRONMENTAL CONDITIONS 25 deg. C, 67 %RH, 978 hPa CHANNEL 1 6 11 CHANNEL FREQUENCY
(MHz) 2412 2437 2462 6dB BANDWIDTH
(MHz) 11.72 11.68 11.64 MINIMUM LIMIT
(MHz) 0.5 0.5 0.5 PASS/FAIL PASS PASS PASS Report No.: RF911122R04B ADT No.: 920430R04 28 Issued: May 14, 2003 FCC ID: MCLT60H656 CH1 Report No.: RF911122R04B ADT No.: 920430R04 29 Issued: May 14, 2003 FCC ID: MCLT60H656 CH6 Report No.: RF911122R04B ADT No.: 920430R04 30 Issued: May 14, 2003 FCC ID: MCLT60H656 CH11 Report No.: RF911122R04B ADT No.: 920430R04 31 Issued: May 14, 2003 FCC ID: MCLT60H656 4.4 MAXIMUM PEAK OUTPUT POWER 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT The Maximum Peak Output Power Measurement is 30dBm. 4.4.2 TEST INSTRUMENTS Description & Manufacturer Model No. Serial No. Calibrated Until SINGLE CHANNEL POWER METER NRVS 100026 Mar. 06, 2004 PEAK POWER SENSOR NRV-Z32 100013 Mar. 06, 2004 NOTE:
1. The measurement uncertainty is less than +/- 2.6dB, which is calculated as per the NAMAS document NIS81. 2. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. Report No.: RF911122R04B ADT No.: 920430R04 32 Issued: May 14, 2003 FCC ID: MCLT60H656 4.4.3 TEST PROCEDURES The transmitter output was connected to the power meter. 4.4.4 DEVIATION FROM TEST STANDARD No deviation 4.4.5 TEST SETUP EUT POWER METER 4.4.6 EUT OPERATING CONDITIONS Same as Item 4.3.6. Report No.: RF911122R04B ADT No.: 920430R04 33 Issued: May 14, 2003 FCC ID: MCLT60H656 4.4.7 TEST RESULTS EUT 802.11b Wireless LAN MiniPCI Card MODEL T60H656 INPUT POWER
(SYSTEM) 120Vac, 60 Hz TESTED BY Eric Lee ENVIRONMENTAL CONDITIONS 27 deg. C, 60 %RH, 978 hPa CHANNEL 1 6 11 CHANNEL FREQUENCY
(MHz) 2412 2437 2462 PEAK POWER OUTPUT
(dBm) 11.4 11.5 11.5 PEAK POWER LIMIT
(dBm) PASS/FAIL 30 30 30 PASS PASS PASS Report No.: RF911122R04B ADT No.: 920430R04 34 Issued: May 14, 2003 FCC ID: MCLT60H656 4.5 POWER SPECTRAL DENSITY MEASUREMENT 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT The Maximum of Power Spectral Density Measurement is 8dBm. 4.5.2 TEST INSTRUMENTS Description & Manufacturer Model No. Serial No. Calibrated Until R&S SPECTRUM ANALYZER FSEK30 100049 July 24, 2003 NOTE:
1. The measurement uncertainty is less than +/- 2.6dB, which is calculated as per the NAMAS document NIS81. 2. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. Report No.: RF911122R04B ADT No.: 920430R04 35 Issued: May 14, 2003 FCC ID: MCLT60H656 4.5.3 TEST PROCEDURE The transmitter output was connected to the spectrum analyzer through an attenuator, the bandwidth of the fundamental frequency was measured with the spectrum analyzer using 3 kHz RBW and 30 kHz VBW, set sweep time=span/3kHz. The power spectral density was measured and recorded. The sweep time is allowed to be longer than span/3KHz for a full response of the mixer in the spectrum analyzer. 4.5.4 DEVIATION FROM TEST STANDARD No deviation 4.5.5 TEST SETUP EUT SPECTRUM ANALYZER 4.5.6 EUT OPERATING CONDITIONS Same as 4.3.6. Report No.: RF911122R04B ADT No.: 920430R04 36 Issued: May 14, 2003 FCC ID: MCLT60H656 4.5.7 TEST RESULTS EUT 802.11b Wireless LAN MiniPCI Card MODEL T60H656 INPUT POWER
(SYSTEM) 120Vac, 60 Hz TESTED BY Eric Lee ENVIRONMENTAL CONDITIONS 22 deg. C, 60 %RH, 978 hPa CHANNEL NUMBER 1 6 11 CHANNEL FREQUENCY
(MHz ) 2412 2437 2462 RF POWER LEVEL IN 3 KHz BW
(dBm)
-11.72
-11.79
-11.85 MAXIMUM LIMIT
(dBm) 8 8 8 PASS/FAIL PASS PASS PASS Report No.: RF911122R04B ADT No.: 920430R04 37 Issued: May 14, 2003 FCC ID: MCLT60H656 CH1 Report No.: RF911122R04B ADT No.: 920430R04 38 Issued: May 14, 2003 FCC ID: MCLT60H656 CH6 Report No.: RF911122R04B ADT No.: 920430R04 39 Issued: May 14, 2003 FCC ID: MCLT60H656 CH11 Report No.: RF911122R04B ADT No.: 920430R04 40 Issued: May 14, 2003 FCC ID: MCLT60H656 4.6 BAND EDGES MEASUREMENT 4.6.1 LIMITS OF BAND EDGES MEASUREMENT Below 20dB of the highest emission level of operating band (in 100KHz Resolution Bandwidth). 4.6.2 TEST INSTRUMENTS Description & Manufacturer Model No. Serial No. Calibrated Until R&S SPECTRUM ANALYZER FSEK30 100049 July 24, 2003 NOTE:
1. The measurement uncertainty is less than +/- 2.6dB, which is calculated as per the NAMAS document NIS81. 2. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 4.6.3 TEST PROCEDURE The transmitter output was connected to the spectrum analyzer via a low lose cable. Set both RBW and VBW of spectrum analyzer to 100 kHz with suitable frequency span including 100 kHz bandwidth from band edge. The band edges was measured and recorded. 4.6.4 DEVIATION FROM TEST STANDARD No deviation Report No.: RF911122R04B ADT No.: 920430R04 41 Issued: May 14, 2003 FCC ID: MCLT60H656 4.6.5 EUT OPERATING CONDITION Same as Item 4.3.6. 4.6.6 TEST RESULTS The spectrum plots are attached on the following 2 pages. D1 line indicates the highest level, D2 line indicates the 20dB offset below D1. It shows compliance with the requirement in part 15.247(C). NOTE (1): The band edge emission plot on the following first page shows 49.71dB delta between carrier maximum power and local maximum emission in restrict band
(2.3734GHz). The emission of carrier strength list in the test result of channel 1 at the item 4.2.7 is 46.6dBuV/m, so the maximum field strength in restrict band is 96.6-49.71=46.89dBuV/m which is under 54 dBuV/m limit. NOTE (2): The band edge emission plot on the following second page shows50.13dB delta between carrier maximum power and local maximum emission in restrict band
(2.4918GHz). The emission of carrier strength list in the test result of channel 11 at the item 4.2.7 is 97.4dBuV/m, so the maximum field strength in restrict band is 97.4-50.13=47.27dBuV/m which is under 54 dBuV/m limit. Report No.: RF911122R04B ADT No.: 920430R04 42 Issued: May 14, 2003 FCC ID: MCLT60H656 Report No.: RF911122R04B ADT No.: 920430R04 43 Issued: May 14, 2003 FCC ID: MCLT60H656 Report No.: RF911122R04B ADT No.: 920430R04 44 Issued: May 14, 2003 FCC ID: MCLT60H656 4.7 ANTENNA REQUIREMENT 4.7.1 STANDARD APPLICABLE For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section 15.247 (b), if transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6dBi. 4.7.2 ANTENNA CONNECTED CONSTRUCTION The maximum Gain antenna used in this product is inverted F antenna, and the antenna connector type for the EUT is UFL. And the maximum Gain of these antennas is 1.8dBi. Report No.: RF911122R04B ADT No.: 920430R04 45 Issued: May 14, 2003 FCC ID: MCLT60H656 5 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: RF911122R04B ADT No.: 920430R04 46 Issued: May 14, 2003 FCC ID: MCLT60H656 Report No.: RF911122R04B ADT No.: 920430R04 47 Issued: May 14, 2003 FCC ID: MCLT60H656 RADIATED EMISSION TEST Report No.: RF911122R04B ADT No.: 920430R04 48 Issued: May 14, 2003 FCC ID: MCLT60H656 Report No.: RF911122R04B ADT No.: 920430R04 49 Issued: May 14, 2003 FCC ID: MCLT60H656 6 INFORMATION ON THE TESTING LABORATORIES We, ADT Corp., were founded in 1988 to provide our best service in EMC and Safety consultation. Our laboratories are accredited and approved by the following approval agencies according to ISO/IEC 17025, Guide 25 or EN 45001:
USA Germany Japan New Zealand Norway R.O.C. FCC, NVLAP TUV Rheinland VCCI MoC NEMKO BSMI, DGT, CNLA Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5/phtml. If you have any comments, please feel free to contact us at the following:
Lin Kou EMC Lab:
Tel: 886-2-26052180 Fax: 886-2-26052943 Lin Kou Safety Lab:
Tel: 886-2-26093195 Fax: 886-2-26093184 Email: service@adt.com.tw Web Site: www.adt.com.tw Hsin Chu EMC Lab:
Tel: 886-35-935343 Fax: 886-35-935342 Lin Kou RF&Telecom Lab Tel: 886-3-3270910 Fax: 886-3-3270892 The address and road map of all our labs can be found in our web site also. Report No.: RF911122R04B ADT No.: 920430R04 50 Issued: May 14, 2003
1 2 | External Pics | External Photos | 482.82 KiB |
CONSTRUCTION PHOTOS OF EUT Interface I Page 1 Interface II Page 2
1 2 | Internal Pics | Internal Photos | 1.01 MiB |
CONSTRUCTION PHOTOS OF EUT Antenna No. 1 Page 1 Antenna No. 2 Page 2 Page 3 Antenna No. 3 Page 4 Antenna No. 4 Page 5 Antenna No. 5 Page 6 Page 7 Antenna No. 6 Page 8 Page 9
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2003-05-22 | 2412 ~ 2462 | DTS - Digital Transmission System | Class II Permissive Change |
2 | 2002-12-27 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2003-05-22
|
||||
1 2 |
2002-12-27
|
|||||
1 2 | Applicant's complete, legal business name |
HON HAI Precision Ind. Co., Ltd.
|
||||
1 2 | FCC Registration Number (FRN) |
0010777365
|
||||
1 2 | Physical Address |
5F-1, 5, Hsin-An Road Hsinchu Science-Based Industrial Park
|
||||
1 2 |
5F-1, 5, Hsin-An Road
|
|||||
1 2 |
Hsinchu, N/A
|
|||||
1 2 |
Taiwan
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
h******@AmericanTCB.com
|
||||
1 2 |
h******@americanTCB.com
|
|||||
1 2 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 2 | Grantee Code |
MCL
|
||||
1 2 | Equipment Product Code |
T60H656
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
M**** C******
|
||||
1 2 | Title |
Compliance Deputy Manager
|
||||
1 2 | Telephone Number |
+886-********
|
||||
1 2 | Fax Number |
+886-********
|
||||
1 2 |
r******@foxconn.com
|
|||||
app s | Technical Contact | |||||
1 2 | Firm Name |
Advance Data Technology Corporation
|
||||
1 2 | Name |
E****** L******
|
||||
1 2 | Physical Address |
81-1 Luliaoken, 9th Lin, Wulung Tsuen
|
||||
1 2 |
Hsinchu, 307
|
|||||
1 2 |
Taiwan
|
|||||
1 2 | Telephone Number |
+886-********
|
||||
1 2 |
+886 ********
|
|||||
1 2 | Fax Number |
+886-********
|
||||
1 2 |
+886 ********
|
|||||
1 2 |
e******@adt.com.tw
|
|||||
app s | Non Technical Contact | |||||
1 2 | Firm Name |
Advance Data Technology Corporation
|
||||
1 2 | Name |
E**** L********
|
||||
1 2 | Physical Address |
81-1 Luliaoken, 9th Lin, Wulung Tsuen
|
||||
1 2 |
Hsinchu, 307
|
|||||
1 2 |
Taiwan
|
|||||
1 2 | Telephone Number |
+886-********
|
||||
1 2 | Fax Number |
+886-********
|
||||
1 2 |
e******@adt.com.tw
|
|||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
1 2 | Yes | |||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | DTS - Digital Transmission System | ||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Wireless LAN mini PCI Card | ||||
1 2 | Wireless LAN mini PCI card | |||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Single Modular Approval | ||||
1 2 | Purpose / Application is for | Class II Permissive Change | ||||
1 2 | Original Equipment | |||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | Modular Approval. Power Output listed is conducted. Approval is limited to OEM installation only. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. OEM integrators must be provided with antenna installation instructions. OEM integrators and end-users must be provided with transmitter operation conditions for satisfying RF exposure compliance. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. | ||||
1 2 | Modular Approval. Power Output listed is Conducted. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | |||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
Bureau Veritas CPS (H.K.) Ltd. Taoyuan Branch
|
||||
1 2 | Name |
T****** W******
|
||||
1 2 |
R**** C******
|
|||||
1 2 | Telephone Number |
886-2********
|
||||
1 2 | Fax Number |
886-2********
|
||||
1 2 |
t******@adt.com.tw
|
|||||
1 2 |
r******@tw.bureauveritas.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | CE | 2412.00000000 | 2462.00000000 | 0.0140000 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15C | 2412.00000000 | 2462.00000000 | 0.0140000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC