FCC ID: ACJ-B21-R10003 Compact Stereo System with Bluetooth Transmitter

 

Owners Manual Compact Stereo System Model No. SC-HC55 SC-HC35 Dear customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. Please keep this manual for future reference. If you have any questions contact U.S.A. and Puerto Rico: 1-800-211-PANA (7262) Canada: 1-800-561-5505 Only for U.S.A. and Puerto Rico: The warranty can be found on page 26 Only for Canada: The warranty can be found on page 27 Included Installation Instructions (

2, 6) The installation should never be done by any other than a qualified installation specialist. Before commencing work, carefully read these installation instructions and the operating instructions to ensure that installation is performed correctly.

(Please keep these instructions. You may need them when maintaining or moving this unit.) La referencia rpida en espaol se puede encontrar en la pgina 18-24. P PC RQTX1260-P

IMPORTANT SAFETY INSTRUCTIONS Batteries Danger of explosion if battery is incorrectly replaced. Replace only with the type recommended by the manufacturer. Mishandling of batteries can cause electrolyte leakage and may cause a fire.

Do not heat or expose to flame.

Do not leave the battery(ies) in a car exposed to direct sunlight for a long period of time with doors and windows closed.

Do not take apart or short circuit.

Do not recharge alkaline or manganese batteries.

Do not use batteries if the covering has been peeled off.

Remove batteries if you do not intend to use the remote control for a long period of time. Store in a cool, dark place. When disposing the batteries, please contact your local authorities or dealer and ask for the correct method of disposal. Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference. 1 2 3 4 5 6 7 Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 8 9 10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11 Only use attachments/accessories specified by the manufacturer. 12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13 Unplug this apparatus during lightning storms or when unused for long periods of time. 14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. WARNING Unit To reduce the risk of fire, electric shock or product damage,

Do not expose this unit to rain, moisture, dripping or splashing.

Do not place objects filled with liquids, such as vases, on this unit.

Use only the recommended accessories.

Do not remove covers.

Do not repair this unit by yourself. Refer servicing to qualified service personnel. Power cord Install this unit so that the power cord can be unplugged from the socket outlet immediately if any problem occurs. CAUTION Unit This unit utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Do not place sources of naked flames, such as lighted candles, on this unit. Placement To reduce the risk of fire, electric shock or product damage,

Do not install or place this unit in a bookcase, built-in cabinet or in another confined space. Ensure this unit is well ventilated.

Do not obstruct this units ventilation openings with newspapers, tablecloths, curtains, and similar items. 2

The model number and serial number of this product can be found on either the back or the bottom of the unit. Please note them in the space provided below and keep for future reference. MODEL NUMBER SERIAL NUMBER User memo:

DATE OF PURCHASE DEALER NAME DEALER ADDRESS TELEPHONE NUMBER Product Identification Marking is located on bottom of the unit.

Made for iPod and Made for iPhone mean that an electronic accessory has been designed to connect specifically to iPod, or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, or iPhone may affect wireless performance. iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Panasonic Corporation is under license. Other trademarks and trade names are those of their respective owners. MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.

-If you see this symbol-

Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal. Listening Caution

(Inside of product)

Selecting fine audio equipment such as the unit youve just purchased is only the start of your musical enjoyment. Now its time to consider how you can maximize the fun and excitement your equipment offers. This manufacturer and the Electronic Industries Associations Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortionand, most importantly, without affecting your sensitive hearing. We recommend that you avoid prolonged exposure to excessive noise. Sound can be deceiving. Over time your hearing comfort level adapts to higher volumes of sound. So what sounds normal can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts. To establish a safe level:

Start your volume control at a low setting. Slowly increase the sound until you can hear it comfortably and clearly, and without distortion. Once you have established a comfortable sound level:

Leave it there. Taking a minute to do this now will help to prevent hearing damage or loss in the future. After all, we want you listening for a lifetime. About descriptions in this Owners Manual Operations in these instructions are described using remote control, but you can do the operations with the main unit if the controls are the same. Your unit may not look exactly as illustrated. This Owners Manual is applicable to models SC-HC55 and SC-HC35. Unless otherwise indicated, illustrations in this Owners Manual are of SC-HC55.

[HC55] :indicates features applicable to SC-HC55 only.

[HC35] :indicates features applicable to SC-HC35 only. Pages to be referred to are indicated as

[CD] :indicates CD-DA (except MP3).

[MP3] :indicates MP3 files. 3 Table of contents IMPORTANT SAFETY INSTRUCTIONS.................................2 Listening Caution...................................................................3 Accessories............................................................................4 Unit and media care...............................................................4 Connections ...........................................................................5 Attaching the unit to a wall (optional)..................................6 Control reference guide ........................................................8 Opening/Closing the sliding door ........................................9 Disc operations......................................................................9 Sound adjustment................................................................10 Radio operations..................................................................11 Timer .....................................................................................11 Listening to audio from iPod or iPhone.............................12

[HC55] Using a Bluetooth compatible device.....................13 Others ...................................................................................15 Troubleshooting...................................................................15 Specifications.......................................................................17 Spanish Quick Reference/ Referencia rpida en espaol Conexiones...........................................................................18 Gua de referencia del mando a distancia .........................19 Abrir/Cerrar la puerta deslizante ........................................20 Operaciones con discos .....................................................20 Operaciones con la radio....................................................21 Ajuste de sonido..................................................................22 Sincronizador.......................................................................22 Escuchar audio de un iPod o iPhone.................................23

[HC55] Uso de un dispositivo compatible con Bluetooth ..........24 Limited Warranty (ONLY FOR U.S.A. AND PUERTO RICO)........26 Limited Warranty (ONLY FOR CANADA) ..................................27 Clean discs DO DO NOT Wipe with a damp cloth and then wipe dry. Disc handling precautions Handle discs by the edges to avoid inadvertent scratches or fingerprints on the disc. Do not attach labels or stickers to discs. Do not use record cleaning sprays, benzine, thinner, static electricity prevention liquids or any other solvent. Do not use the following discs:

Discs with exposed adhesive from removed stickers or labels (rented discs etc.). Discs that are badly warped or cracked. Irregularly shaped discs, such as heart shapes. Accessories Check the supplied accessories before using this unit. 1 Remote control

([HC55] N2QAYB000643)

([HC35] N2QAYB000641) 1 FM indoor antenna

(RSAX0002) 1 Battery for remote control 1 AM loop antenna

(N1DYYYY00010) 1 AC power supply cord

(K2CB2CB00021) Wall mounting accessories 2 Safety holder screws

(XYN4+8FJK) 2 Wall mount brackets 2 Safety holders

(RGQ0634-K) 2 Rear pads

(RMQX1082-K)

(ONLY FOR CANADA) The enclosed Canadian French label sheet corresponds to the English display on the top of the unit.

(RKA0252-K) Product numbers correct as of January 2011. These may be subject to change. Do not use AC power supply cord with other equipment. Only for U.S.A. and Puerto Rico:

To order accessories, refer to Accessory Purchases (United States and Puerto Rico) on page 26. For Canada: To order accessories, call the dealer from whom you made your purchase. The remote control information Insert so the poles (

and

) match those in the remote control. Place this side in before the other side. Use alkaline or manganese batteries.

Unit and media care Pull out the AC power plug from the outlet before maintenance. Clean this unit with a soft, dry cloth Never use alcohol, paint thinner or benzine to clean this unit. Before using chemically treated cloth, carefully read the instructions that came with the cloth. When dirt is heavy, wring the cloth moistened in water tightly to wipe the dirt, and then wipe it with a dried cloth. Do not use tissues or other materials that can fall apart. Small grains may get stuck inside the speaker cover. Maintenance of the lens Clean the lens regularly to prevent malfunctions. Use a blower to remove dust and a cotton swab if it is extremely dirty. You cannot use a CD type lens cleaner. Do not leave the sliding door open for prolonged periods of time. This will cause the lens to get dirty. Be careful not to touch the lens with your fingers. Lens 4 Connections Notes on speakers These speakers do not have magnetic shielding. Do not place them near a television, personal computer or other devices easily influenced by magnetism. Back View Exhaust holes Basic Connections Connect the FM indoor antenna. Tape the antenna to a wall or column, in a position with the least amount of interference. Adhesive tape FM indoor antenna Connect the AM loop antenna. Keep the loop antenna cord away from other wires and cords. Stand the antenna up on its base until it clicks. AM loop antenna Connect the AC power supply cord. Connect the AC power supply cord after all other connections are complete. Turn the unit on after a few seconds. Power consumption in standby mode:

Approx. 0.05 W To household AC outlet Additional Connections Open the EXT-IN AUX/Headphone cover to connect headphones or external music devices (e.g. MP3 player). Push the projecting part to open the cover Top View

. EXT-IN AUX/

Headphone cover Projecting part Connect the headphones (not supplied) Reduce the volume level and connect the headphones. Plug type: 3.5 mm (1/8 ) stereo To prevent hearing damage, avoid listening for prolonged periods of time. Excessive sound pressure from earphones and headphones cause hearing loss. Connect an external music device (for AUX mode) Plug the audio cable (not supplied) into the EXT-IN AUX jack Plug type: 3.5 mm (1/8 ) stereo Press [EXT-IN, RADIO] repeatedly to select AUX and start playback on the connected device. You can select the sound input level of the external device. Press [SOUND] repeatedly to select INPUT

[HC55]

LEVEL. Press [

] to select HIGH or NORMAL.

[HC35] Press [INPUT LEVEL] repeatedly to select HIGH or

NORMAL. Switch the equalizer off or turn the volume of the external device down to reduce the input signal. High level of input signal will distort the sound. For details, refer to the instruction manual of the other equipment. Cables and devices are not supplied. 5 Attaching the unit to a wall (optional) Installation accessories Supplied accessories 2 Safety holder screws 2 Safety holders 2 Wall mount brackets 2 Rear pads Commercially available accessories

(not supplied) 4 Wall bracket fixing screws Keep the wall mount brackets out of reach of children to prevent swallowing. Keep the rear pads out of reach of children to prevent swallowing. Keep the screws out of reach of children to prevent swallowing. Keep the safety holder out of reach of children to prevent swallowing. Use screws with a nominal diameter of the material of the wall (e.g., wood, steel, concrete, etc.) 4 mm (5/32 ), which are suitable to Notes on installation Before installation, read the Safety precautions and Wall mount instructions for correct installation. For optimal performance and to prevent potential problems, do not install this unit:

at locations other than vertical walls.

near a sprinkler or a sensor.

near high-voltage lines or power sources.

near heating device.

at locations where the unit is subject to vibration or impact.

near sources of magnetism, heat, vapor, airborne grease, etc.

at locations where there may be water droplets (e.g. under an air Do not install this unit under ceiling lights (e.g. spotlight, halogen light, etc.).

Failure to do so may bend the cabinet or lead to damage caused by conditioner). high heat. Use a proper installation method that suits the structure and material of the wall. Use a soft blanket or cloth to prevent damage to the product or floor during installation. When tightening screws, make sure the screws are not loosely-tightened or overtightened. Secure a safe surrounding area and pay attention to safety during installation. Panasonic is not liable for incidental or consequential damages resulting from improper installation or operation. Safety precautions Wall mount instructions WARNING!

Only a qualified building contractor shall install or uninstall this unit.

Improper installation may cause the unit to fall, resulting in injury. To prevent injury, the unit must be securely attached to the wall in accordance with the installation instructions. Do not install the unit where it cannot support the load.

If the mounting parts are not strong enough, this may cause the unit to fall, resulting in injury. Do not use installation methods other than instructed.

This may cause the unit to fall and be damaged, resulting in injury. Do not install the unit at locations other than vertical walls.

This may cause the unit to fall and be damaged, resulting in injury. Take the safety factor for mounting strength into account (approx. 10 times the product weight).

Insufficient strength will cause the unit to fall, resulting in injury. The wall on which the unit is to be attached to should be capable of supporting 20 kg (44 lbs) per screw.

Insufficient strength of the walls will cause the unit to fall in the long run. Do not disassemble or modify the wall-mounting hanger.

This will cause the unit to fall and be damaged, resulting in injury. CAUTIONS!

Before installation, turn the unit off and disconnect the AC power supply cord from the AC outlet. 1 Detach the stand from the unit. Unscrew the fixing screw (4 pieces) at the bottom of the unit. Bottom of main unit Stand Fixing screw Soft blanket or cloth Gently pull the bottom of the stand and slide the stand off the unit. Keep the removed screws and stand in a safe place. Do not install this unit at humid or dusty locations, or locations where airborne grease or steam may come into contact with the unit, or under an air conditioner where water may drip onto the unit.

This may have negative impact on the unit, resulting in fire or electric shock. Secure enough space of more than 30 cm (11 3/16 ) above the main unit and more than 10 cm (3 15/16 ) on the left and right sides respectively. Keep space between the wall and rear of the unit clear of obstructions.

Blocking the exhaust holes on the main unit may result in fire. Use the designated components for installation.

Otherwise, the main unit may fall and be damaged, resulting in injury. Prevent the mounting screws or power cord from coming into contact with metal parts inside the wall during installation.

Failure to do so may cause electric shock. When removing the main unit, remove the wall mounting screws as well.

Otherwise the wall mounting screws may hit a person and lead to injury. Install the unit at a height where the EXT-IN AUX jack and operation buttons can be seen for safe operation.

Operating at improper position may cause the unit to fall and be damaged, resulting in injury. 6 2 Measure and mark the position of the wall mount brackets (Both sides). Use figures below to identify the screwing positions. The position to attach the wall mount brackets 5 Fix the safety holders onto the wall mount

. brackets with the safety holder screws Screw tightening torque: 80 N cm (17.98 lbf-ft) to 120 N cm

(26.98 lbf-ft). Space required 39 mm

(1 7/32 ) 12.5 mm (1/2 ) 229 mm (9 1/32 ) Safety holder screw Safety holder 300 mm (11 13/16 ) 229 mm (9 1/32 ) 480 mm (18 29/32") 680 mm (30 23/32 ) Fall-prevention measure (optional) This measure is only designed as a backup feature to prevent the unit from falling. This will not guarantee that the unit will not fall or get damaged. Thread a cord (not supplied) through the 2 holes in the safety holder before step 5. Fix the cord to the wall with a screw (not supplied) after step 5. Fix the cord to the screw so that a slack of no more than 5 cm

(1 31/32 ) is kept. 3 Attach the wall mount bracket to the wall with 2 screws

. (Both sides) Use a spirit level to ensure both wall mount brackets are level. Use a screw which is strong enough to support the weight of at least 20 kg (44.1 lbs). At least 30 mm (1 3/16 ) 7.5 mm (19/64 ) to 9.4 mm (3/8 ) 4 mm

(5/32 ) Wall mount bracket 4 Hang the unit on the wall. Hook the unit securely onto the wall mount brackets. Connect the FM/AM antenna and the AC power supply cord to the unit before hanging the unit onto the wall. (

After hanging the unit, release your hand carefully to confirm the unit sits securely on the wall. Before attaching, stick the rear pads (supplied) to 5)

. Metal fitting Screw Cord Cord Slot for cord Wall 7 Control reference guide Remote control Front view

9)

[6]

11) 12, 12)

/I] (

[ 10]

9, 10, 11,

], 9, 11,

[SLEEP] (

Standby/on switch [

[POWER, 15) Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power. Numeric buttons

[1-9, 0, 10] (

15) To select a 2-digit number e.g. 16: [ 10]

[1]

To select a 3-digit number e.g. 226: [ 10]

[6]

[2]

[2]

[DEL] (

10)

[HC55] [

, iPod] (

13)

[HC35] [iPod] (

[CD] (

11, 12, 13)

[HC55] [

[SOUND] (

5, 9, 10)

[D.BASS] (

10)

[PLAY MENU] (

[iPod MENU] (

[HC55] [ MENU] (

9, 10, 11, 12, 14)

[DISPLAY] (

[ DIMMER]

Press and hold to dim the display panel. Press and hold again to cancel.

[HC55] [OPEN/CLOSE SENSOR] (

[HC35] [INPUT LEVEL]

5)

[iPod

[iPod

[HC55] Sensor activity indicator*

[PLAY, 9, 10, 12, 13)

, OPEN/CLOSE]

14) 9, 11, 12) 9, 10) 12)

], [OK] (

14) 5, 9, 14) 9, 10, 11) 9) 9)

11, 14) 14) 14) 10) 11) 11) 10, 11) 9, 10, 12, 13)

[CLOCK/TIMER] (

[PROGRAM] (

[+, VOL ,]

VOLUME +] (

Adjusts sound volume.

[MUTE] (

Mutes the sound. Press again to cancel. MUTE is also canceled when the volume is adjusted or the unit is turned off.

[EXT-IN, RADIO]

[RADIO/EXT-IN] (

15)

[HC55] [

[PRESET EQ] (

[RADIO MENU] (

[AUTO OFF]

This function allows you to turn the unit off (except in radio mode) after the unit is left unused for about 30 minutes. When the function is turned on, the A.OFF indicator light.

[AUTO PRESET] (

11)

[CD ] (

[CD , OPEN/CLOSE]

[HC55] Sensor activity indicator*

Standby indicator

[HC55] Open/Close sensor

Speaker Display Sliding door

[HC55] Microphone (

14)

[HC55] Bluetooth indicator

Remote control signal sensor Distance:

Within approx. 7 m (23 ft) directly in front. 13) 9) 9)

* The sensor activity indicator will light when the Open/Close sensor is turned on. One of the indicators will flash while the sliding door is opening or closing. Main unit Buttons such as They can be used interchangeably. Top view function the same as the remote control. 8 Opening/Closing the sliding door Preparation Press [

] to turn the unit on. Opening the sliding door For disc operations:

While the sliding door is closed, press [CD ]

to open the sliding door. For iPod/iPhone operations:

While the sliding door is closed, press [iPod to open the sliding door. Closing the sliding door

] again. Press [CD ] or [iPod Keep fingers away from the sliding door when it is closing to avoid possible minor injuries. Damage may occur if the sliding door is forced closed. Be careful of CD hitting the sliding door while being removed. The sliding door will not close if the docking switch lever is not returned to the original position.

[HC55] Open/Close sensor With this function the sliding door can be opened without pressing a button. The sliding door will open or close by moving your hand over the sensor. For disc operations:

While the sliding door is closed, move your hand from to

. To close the sliding door, move your hand from to For iPod/iPhone operations:

While the sliding door is closed, move your hand from to

. To close the sliding door, move your hand from to

. To turn the Open/Close sensor off Press [OPEN/CLOSE SENSOR]. Each time the button is pressed, the sensor is turned on

ON SENSOR) or off (OFF SENSOR). To add a sound effect when the sliding door opens/closes (when the sensor is used.) Press [SOUND] repeatedly to select BUZZER.

] to select the following setting. Press [

LOW:

Set the sound effect level to low. MID:

Set the sound effect level to medium. HIGH:

Set the sound effect level to high. OFF:

Turn the sound effect off.

] or [

The open/close sensor might be unintentionally activated if an object, hand, part of your arm, pets or children move near the sensor. If the open/close sensor does not work or if the sensors reaction range becomes smaller, open/close the sliding door using the buttons on the unit or the remote control. The disc operation side of the sliding door will not open during CD playback or pause. Disc operations Inserting a disc 1 Press [

] to turn the unit on. 2 Open the sliding door. (

left) 3 With the label of the disc facing towards you, tilt the disc into the disc tray under the sliding door.

4 Place the disc onto the spindle in the center and then push the disc down until it clicks into place. left) 5 Close the sliding door. (

Removing a disc Open the sliding door. Hold the center and the top right of the disc and pull the top right of the disc to unlock it from the spindle. Tilt the disc so as not to touch the sliding door or the lens and remove the disc. Basic play above). 1 Press [

] to turn the unit on. 2 Insert the disc to be played (

3 Press [CD]. 4 Press [

Stop Pause Skip

] to start play.

Search [CD]

Direct access play

(Play starts from the track you selected.) View contents information

]. Press again to resume play.

] or [

] to skip track.

] to skip album. (MP3) Press [

Press [

Press [

Press [

Press and hold [

[CD]:

Press the numeric buttons to select the track.

[MP3]:

] or [

, Press [

Press [

numeric buttons to select the track.

] to select the album.

] once and then the This function does not work during 10) random play or program play. (

Press [DISPLAY] repeatedly during play or pause. The current tracks information, etc. is displayed. Maximum number of displayable characters:

approximately 30 This unit supports ver. 1.0, 1.1 and 2.3 ID3 tags. Text data that is not supported will not be displayed or shown differently. Repeat play above)

REPEAT. After performing steps 1-3 in Basic play (

1 Press [PLAY MENU] repeatedly to select 2 Press [

[OK]. 3 Press [

To stop repeat play, select OFF REPEAT in step 2.

] to start play.

] to select ON REPEAT and press 9 Disc operations (Continued) Play mode function After performing steps 1-3 in Basic play (

1 Press [PLAY MENU] repeatedly to select PLAY MODE. 2 Press [

] to select the following mode and 9)

, press [OK]. 1-TRACK 1TR:

1-ALBUM 1ALBUM:

[MP3]

RANDOM RND:

1-ALBUM RANDOM 1ALBUM RND:

[MP3]

Plays one selected track on the disc. Plays one selected album on the disc. Press [

] to select the album. Plays a disc randomly. Plays all tracks in one selected album randomly. Press [

] to select the album. 3 Press [

] to start play. During random play, you cannot skip to the previous track. The current play mode is cleared when you open the sliding door. To repeat program play or selected play mode, select ON REPEAT in PLAY MENU. (

9) Program play Enables you to program up to 24 tracks. After performing steps 1-3 in Basic play (

1 Press [PROGRAM] during the stop mode. 2 [CD]:

Press the numeric buttons to select the track. 9) To program more tracks, continue by pressing the numeric buttons.

[MP3]:

] to select the album.

] once and then the numeric buttons to Press [

Press [

select the track. Press [OK]. To program more tracks, repeat steps

] to start play. Notes on CD-R/CD-RW This unit can play CD-R and CD-RW recorded with CD-DA or MP3. Use an audio recording disc for CD-DA and finalize* it when you finish recording.

* A process performed after recording that enables CD-R or CD-RW players to play audio CD-R and CD-RW. The unit may not be able to play some discs due to the condition of the recording. Do not use irregularly shaped CDs. Do not attach extra labels and stickers. Do not use CDs with labels and stickers that are coming off or with excessive adhesive under the labels and stickers. Do not attach scratch-proof covers or any other kind of accessories. Do not write anything on the CDs. Do not clean CDs with liquids (Wipe with a soft and dried cloth). Note about using a DualDisc The digital audio content side of a DualDisc does not meet the technical specifications of the Compact Disc Digital Audio (CD-DA) format so play may not be possible. Do not use a DualDisc in this unit as it may not be possible to insert it correctly and it may get scratched or scraped. Creating MP3 files playable on this unit Maximum number of tracks and albums: 999 tracks and 254 albums

(Excluding Root folder). Compatible compression rate: Between 64 kbps and 320 kbps (stereo). 128 kbps (stereo) is recommended. Disc formats: ISO9660 level 1 and level 2 (except for extended formats). The time for reading TOC depends on the number of the tracks, folders or folder structures. Limitations on MP3 This unit is compatible with multi-sessions and it takes more time to start playing. This unit cannot play files recorded using packet write. If the disc includes both MP3 and normal audio data (CD-DA), the unit plays the type recorded in the inner part of the disc. If the disc includes both MP3 and other types of audio data (e.g. WMA or WAV), the unit plays only the MP3. Depending on how you create the MP3 files, they may not play in the order you numbered them or may not play at all. Sound adjustment The following sound effects can be added to the audio output. Preset EQ Press [PRESET EQ] repeatedly to select

HEAVY, SOFT, CLEAR, VOCAL or

FLAT.

. Bass or Treble 3 Press [

Cancel program mode Check program contents Delete last programmed track Clear all programmed tracks Press [PROGRAM] in the stop mode to clear PGM indicator from the display. Press [

] when PGM is displayed in the stop mode. Press [DEL] in the stop mode.

] or [

Surround Sound Press [

Press [

CLR ALL.

] in the stop mode.

] again while blinking

] to adjust the level (-4 to Press [SOUND] repeatedly to select

BASS or TREBLE. Press [

+4). Press [SOUND] repeatedly to select

SURROUND. Press [

ON SURROUND.

] to select

, To cancel surround sound, select

OFF SURROUND in step If interference in FM stereo reception increases, cancel the surround sound effect. The program memory is cleared when you open the sliding door. D.Bass Press [D.BASS] during play to select

ON D.BASS or OFF D.BASS. You may experience a reduction in sound quality when these effects are used with some sources. If this occurs, turn the sound effects off. 10 Radio operations Manual tuning Timer Setting the clock 1 Press [EXT-IN, RADIO] repeatedly to select 2 Press [

FM or AM.

] or [

] to select the frequency of the required station.

ST is displayed when a stereo FM broadcast is being received. To tune automatically, press and hold [

the frequency starts changing rapidly.

] or [

] until To cancel auto tuning, press [

Auto tuning may not function when there is excessive interference.

] once again.

] or [

To improve FM sound quality Press [RADIO MENU] while receiving FM broadcasts. Press [

Press [

] to select FM MODE.

] to select MONO.

, to return to stereo broadcasts. Select STEREO in Step

MONO is canceled if the frequency is changed. To improve AM sound quality Press [RADIO MENU] to select B.PROOF while receiving AM broadcasts. Press [

BP 2) and press [OK].

] to select the beat proof setting (BP 1 or

, This setting is reset to BP 1 when changes are made (e.g. frequency is changed). Memory preset You can preset up to 30 FM channels and 15 AM channels. Preparation Press [EXT-IN, RADIO] repeatedly to select FM or AM. Automatic presetting Press [OK] to switch between the LOWEST and

CURRENT frequency. Press [AUTO PRESET].

PGM starts to flash and the tuner starts to preset all the stations it can receive into the channels in ascending order.

] or [

Manual presetting Press [

Press [PROGRAM]. While PGM is flashing, press the numeric buttons to select a channel.

] to tune to the required station. The station occupying a channel is erased if another station is preset in that channel. To preset more stations, repeat steps

Selecting a preset station Press [

] or [

] to select the channel. Alternatively, press the numeric buttons to select the channel. FM/AM frequency step This unit is factory-set to FM 0.2 MHz and AM 10 kHz, but you can change it to receive broadcasts allocated in FM 0.1 MHz or AM 9 kHz steps. Press [EXT-IN, RADIO] to select FM. Select AM to change the AM frequency steps Press and hold [RADIO/EXT-IN] on the main unit. After a few seconds the display changes to display current minimum frequency. Continue to hold down [RADIO/EXT-IN] on the main unit. When the minimum frequency changes, release the button. This is a 12-hour clock. 1 Press [CLOCK/TIMER] to select CLOCK. 2 Within 10 seconds, press [

] to set the 3 Press [OK]. time.

, To display the clock, press [CLOCK/TIMER]. Reset the clock regularly to maintain accuracy. Play timer You can set the timer to come on at a certain time to wake you up. This unit offers 3 optional play timers. Preparation above).

PLAY 1, PLAY 2 or PLAY 3. Turn the unit on and set the clock (

Prepare the music source (disc, radio, iPod/iPhone or AUX) and set the volume. 1 Press [CLOCK/TIMER] repeatedly to select 2 Within 10 seconds, press [

starting time. 3 Press [OK]. 4 Set the finishing time by repeating steps 2 and

] to set the

, 3. To activate the timer

] repeatedly to set the desired 5 Press [PLAY, play timer on. 6 Press [

Check the settings

(When the unit is on or in standby mode) Cancel

] to turn the unit off. Press [CLOCK/TIMER] twice.

(The setting is displayed.) Press [PLAY, indicator from the display.

] twice to clear the timer The timer will start at the preset time, with the volume increasing gradually to the preset level. Sleep timer The sleep timer can turn the unit off after a set time. Press [SLEEP] to turn the sleep function on or off. 30MIN 60MIN 90MIN OFF (Cancel) 120MIN Press [SLEEP] once to check the remaining time. The play timer and sleep timer can be used together. The sleep timer always has the priority. Be sure not to overlap the timer settings. When AUTO OFF is ON and the unit is left unused for about 30 minutes, the unit will shut down even if the play time or sleep time has not expired. To return to the original step, repeat steps After the setting is changed, any previously preset frequency will be cleared.

. 11 Listening to audio from iPod or iPhone Inserting/Removing an iPod/

iPhone Inserting an iPod/iPhone 1 Open the sliding door. (

2 Insert the suitable dock adapter (not supplied) 9) for the iPod/iPhone. Insert the side of the iPod/iPhone dock adapter with the clips facing towards you first and then push the opposite side until it clicks into place. Clips Dock adapter iPod/iPhone docking switch lever Connector Click!

3 Press [

] to unlock the iPod/iPhone dock and then pull the docking switch lever to tilt the iPod/iPhone dock. 4 Connect the iPod/iPhone

(not supplied) firmly. 5 Push the docking switch lever back until it clicks into place. 6 Close the sliding door. (

9) Be sure to remove the iPod/iPhone from its case. Click!

Removing an iPod/iPhone Repeat step 1 and 3 (

above). To remove, simply pull the iPod/iPhone straight out. Repeat step 5 and 6 (

above). If the iPod/iPhone dock is not tilted when connecting or disconnecting the iPod/iPhone, it may cause damage to the connector. Be sure to use a dock adapter that is compatible with your iPod/iPhone. To purchase a dock adapter, consult your iPod/iPhone dealer. Reduce the volume of the main unit to minimum before connecting or disconnecting the iPod/iPhone. iPod operations Preparation Press [iPod] ([HC55]: [

Play Pause

, iPod]) repeatedly to select IPOD.

] or [

Press [

Press [

resume play. Press [

]. Press again to

] or [

Skip track

] or [

Search the current track Press and hold [

Display iPod/iPhone menu/return to previous menu Select contents from iPod/iPhone menu

]. Press [iPod MENU] in the play mode. (Remote control only) Press [

(Remote control only)

] and then [OK]. The operations may vary or not work depending on the iPod/iPhone models. 12 Compatible iPod/iPhone (as of January 2011) Compatibility depends on the software version of your iPod/

iPhone. Name iPod touch 4rd generation iPod nano 6th generation iPod touch 3rd generation iPod nano 5th generation (video camera) iPod touch 2nd generation iPod classic iPod nano 4th generation (video) iPod classic iPod touch 1st generation iPod nano 3rd generation (video) iPod classic iPod nano 2nd generation (aluminum) iPod 5th generation (video) iPod 5th generation (video) iPod nano 1st generation iPhone 4 iPhone 3GS iPhone 3G iPhone Memory size 8 GB, 32 GB, 64 GB 8 GB, 16 GB 32 GB, 64 GB 8 GB, 16 GB 8 GB, 16 GB, 32 GB 120 GB, 160 GB (2009) 8 GB, 16 GB 160 GB (2007) 8 GB, 16 GB, 32 GB 4 GB, 8 GB 80 GB 2 GB, 4 GB, 8 GB 60 GB, 80 GB 30 GB 1 GB, 2 GB, 4 GB 16 GB, 32 GB 8 GB, 16 GB, 32 GB 8 GB, 16 GB 4 GB, 8 GB, 16 GB Depending on the model, it may be necessary to remove the iPod/iPhone and select the album, artist, etc. on the iPod/iPhone. Notes on iPhone:

All phone features can only be controlled by the iPhones touch screen. The unit does not display incoming calls or the phone status (Connect iPhone to this unit via Bluetooth to enjoy extended capabilities). The ringtone of incoming call can be heard from the iPhones speaker. When the unit is in iPod/iPhone mode, the ringtone can also be heard from the units speakers (Connect iPhone to this unit via Bluetooth to enjoy extended capabilities). Connecting or disconnecting the iPhone from the unit will not cancel a call. There is no Apple Inc. specification that will guarantee the iPhone responses above. iPhone responses may vary on new iPhone models or iPhone new software updates. Charging the iPod/iPhone When iPod/iPhone is being charged in standby mode, IPOD CHARGING is shown on the main units display. Check iPod/iPhone to see if the battery is fully charged. If you are not using iPod/iPhone for an extended period of time after recharging has completed, disconnect it from the main unit as the battery will be depleted naturally. (Once fully recharged, additional recharging will not occur.)

[HC55]

Listening to the Internet Radio This unit can output internet radio if vTuner for Panasonic is installed on your iPhone/iPod touch. Visit the below website for the following information about

vTuner for Panasonic:

http://radio.vtuner.com/panasonic/en/

(Compatible iPhone/iPod touch models and software versions, purchasing, installation and operation details.) Preparation Install vTuner for Panasonic to your iPhone/iPod touch. 1 Insert the iPhone/iPod touch to this unit. 2 Press [

RADIO.

vTuner for Panasonic starts.

, iPod] repeatedly to select INTERNET

[HC55] Using a Bluetooth compatible device About using Bluetooth What is Bluetooth?

Bluetooth technology allows you to make a wireless connection with another electronic device. Frequency band used This unit uses the 2.4 GHz frequency band, however other devices may use this frequency as well. To avoid interference with other wireless devices, please follow the cautions listed below. Certification of this device This unit conforms to frequency restrictions and has received certification based on frequency laws, so a wireless permit is not necessary. However, the following actions are punishable by law in some countries:

Taking apart/modifying the unit. Removing specification indications from the rear part of this unit. Usage restrictions Wireless transmission and/or usage with all Bluetooth equipped devices is not guaranteed. Compatible mobile phones capable of wireless transmission include and comply to standards set by the Bluetooth SIG, Inc. However, if the mobile phone is optimized to meet standard specifications, some functions may work. Even so, depending on the specifications and settings of the mobile phone, a connection may not be established, nor are the methods of operation, display, or operation guaranteed. This unit supports Bluetooth security features, however depending on the operating environment and/or settings, this security may not be sufficient. Use caution when transmitting data wirelessly. Please be aware that Panasonic accepts no responsibility for data and/or information that may be compromised during a wireless transmission. Range of use Use this device within an unobstructed 10 m (33 ft) range. The range of usage or perimeter may be shortened depending on any obstructions, devices causing interference, other people in the room, or the construction of the building. Please note that the range mentioned above is not guaranteed. Effects from other devices It is possible that this unit may not operate correctly or you may experience other effects of instability such as broken up audio, etc. when other devices are placed within close proximity. Therefore, in order to prevent signal interference, we recommend separating this unit from the following devices during use:

Microwave oven/Wireless LAN/Electronic devices/Audio & Video devices/Office Assistant machines & devices/Digital cordless phones/Fax machines, etc. If you live in close proximity to a broadcasting studio and the signal is too strong, the unit may not operate correctly. When using a notebook PC with a wireless LAN transmitter, do not use this unit and the wireless LAN at the same time. If you are still experiencing noise even outside of the 5 m (16.4 ft) range of a wireless LAN device, turn the power to the wireless LAN device off. Intended usage limitations This unit is intended for normal, general use. This unit is not developed or manufactured with the intention of use in high safety or hazardous occupations. Do not use this unit in these kinds of environments or occupations. The following examples require extreme caution, and can directly result in loss of life, or extreme bodily harm. e.g.) Nuclear Engineering, and control of a nuclear reaction/automated control of aircraft/air traffic control management/controlling movement of heavy freight systems/control of life support or extension systems/control of weapons systems and/or missile launch systems, etc. Bluetooth pairing Preparation Pair the Bluetooth device with this unit to create an audio connection. 1 Press [

, iPod] repeatedly to select

BLUETOOTH. When using it for the first time, it enters pairing mode automatically. 2 While this unit is in pairing mode, access the Bluetooth menu of the Bluetooth device and execute a Bluetooth search to find this unit

(SC-HC55). Please refer to the Bluetooth device user manual for further instruction on how to connect a Bluetooth device. If prompted for the passkey, enter 0000. 3 If pairing is successful, the paired devices name will be displayed for 2 seconds. The Bluetooth indicator lights up. The unit is now ready to be used with the Bluetooth device. Make sure the Bluetooth device supports A2DP (Advance Audio Distribution Profile). This unit supports the A2DP reception which is copyright-protected by SCMS-T method. A2DP enables you to stream stereo sound from an audio source (mobile phone, PC or laptop) to this unit via Bluetooth. Depending on the specification or setting of mobile phones, connection may not be established, or operation and display may vary. You can register up to 6 devices into this unit. Disconnect the current Bluetooth device and refer to To register more devices (

If you register more than the maximum device number, the oldest device in connection history will be overwritten. If a registered device is re-registered, it will be overwritten. 14). Basic play Pair the Bluetooth device with this unit to create an audio connection. 1 Press [

BLUETOOTH. 2 On the Bluetooth device:

, iPod] repeatedly to select Select this unit (SC-HC55) on the Bluetooth setup screen to make the connection. 3 On the Bluetooth device:

Start playback of a music source. If the device is connected, the music will be heard on this unit. The Bluetooth indicator lights when there is a connection. Please refer to the Bluetooth device user manual if required. 4 You can also make the following controls with the remote control. Play Stop Pause Skip track Display information

] to start play. Press [

Press [

Press [

Press [

Press [DISPLAY] repeatedly.

]. Press again to resume play.

] or [

]. 13

[HC55] Using a Bluetooth compatible device

(Continued) To utilize these functions, the Bluetooth device must support AVRCP (Audio Video Remote Control Profile). This unit cannot transmit data to a Bluetooth device. When playing iPod/iPhone by Bluetooth with the main unit, intermittent sound may be experienced if you leave the iPod/iPhone Bluetooth menu screen active or when making Bluetooth registration and connection. If this occurs, please exit the iPod/iPhone Bluetooth menu screen. When playing music by iPod/iPhone via Bluetooth connection and the iPod/

iPhone is connected into this unit iPod/iPhone dock, the audio will not be re-produced while BLUETOOTH is selected. Select IPOD to continue enjoying the music. Input level

BLUETOOTH.

, iPod] repeatedly to select You can select the sound input level of the Bluetooth device. 1 Press [

2 Press [SOUND] repeatedly to select INPUT LEVEL. 3 Press [

] to select , or .

, Select if the sound is distorted. Display function Press [DISPLAY] repeatedly to view the information of the current connected device. BLUETOOTH Connected device name Connected profiles Hands-Free Profile (HFP) This unit works as a Bluetooth hands-free for your mobile phones. To answer a call

IN CALL blinks) To cancel a call To adjust the sound volume To mute the microphone

]. CALLING starts blinking on Press [

the display (Talk into the units microphone). Press [

] again to transfer the call to the mobile phones (TRANSFER blinks. You may now converse using the mobile phone). Press [

Press [+, VOL ,] (Adjustable from

TEL VOL 1 to TEL VOL 10). Press [MUTE]. Press again to cancel.

(During MIC MUTE, the caller is not able to hear your voice).

]. This unit does not work with Headset Profile (HSP). When the mobile phone is too close to the microphone of this unit, noise may occur. Always keep the mobile phone away from the microphone of this unit when making a call. The audio from a disc will be paused while calling in hands-free mode. 14 Disconnecting a Bluetooth device

, iPod] repeatedly to select 1 Press [

2 Press [ MENU] to display DISCONNECT?

BLUETOOTH. and then press [OK]. A confirmation message is displayed.

] to select YES and then press 3 Press [

[OK]. The connection can also be stopped when you disable Bluetooth transmission on the connected Bluetooth device. Advanced functions Preparation Press [

, iPod] repeatedly to select BLUETOOTH. These functions are unavailable if a device is connected. Disconnect the Bluetooth devices to display these functions. To register more devices 1 Press [ MENU] repeatedly to select

NEW DEV. and then press [OK]. The unit enters pairing mode and PAIRING starts blinking on the display. 2 While this unit is in pairing mode, access the Bluetooth menu of the Bluetooth device and execute a Bluetooth search to find this unit

(SC-HC55). If prompted for the passkey, enter 0000. To select communication quality 1 Press [ MENU] repeatedly to select 2 Press [

LINK MODE.

] to select the following modes and

, then press [OK]. MODE 1: Connection with emphasis on communication stability MODE 2: Connection with high bit rate for good audio quality

(Communication might easily be disconnected in this mode, select MODE 1 if this occurs). To select Auto Link mode 1 Press [ MENU] repeatedly to select 2 Press [

AUTO LINK.

] to select the following modes and

, then press [OK]. ON:

OFF This unit will automatically select BLUETOOTH when a Bluetooth device is connected. When LINKING is displayed, pressing [ MENU] is invalid. Auto Link works only if your device supports A2DP. The communication quality settings also depend on the settings on the connected device. If the communication quality of the connected device is set for stable communication, the quality of the audio will remain low even if this unit is set to MODE 2. Others Changing the main unit and remote control mode Other Panasonic audio/video equipment may start functioning when you operate the unit using the supplied remote control. You can operate this unit in another mode by setting the remote control operating mode to REMOTE 2. The main unit and remote control must be set to the same mode. 1 Press [EXT-IN, RADIO] to select AUX. 2 Press and hold [RADIO/EXT-IN] on the main unit and [2] on the remote control until the main units display shows REMOTE 2. 3 Press and hold [OK] and [2] on the remote control for at least 4 seconds. To change the mode back to REMOTE 1, repeat the steps above by replacing [2] with [1]. Memory reset (Initialization) When the following situations occur, reset the memory:

There is no response when buttons are pressed. You want to clear and reset the memory contents. To reset memory 1 Disconnect the AC power supply cord. (Wait for at least 3 minutes before proceeding to step 2.) 2 While pressing and holding down [POWER,

I] on the main unit, reconnect the AC power supply cord.

-------- appears on the display. 3 Release [POWER,

/I]. All the settings are returned to the factory preset. You will need to reset the memory items. Troubleshooting Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the following guide do not solve the problem, refer to

Customer Services Directory (United States and Puerto Rico) on page 26 if you reside in the U.S.A. or Puerto Rico, or refer to

Limited Warranty (ONLY FOR CANADA) on page 27 if you reside in Canada. Common problems Incorrect display or play will not start. You have not inserted the disc properly. Insert it correctly. The disc is scratched or dirty (Tracks skipped). There is moisture on the lens. Wait for about an hour and then try again. MP3 cannot be read. You may not be able to play MP3 if you have copied a multi-session disc that has no data between sessions. When creating a multi-session disc, it is necessary to close the session. The amount of data on the disc is too small. Set the amount of data to above 5 MB. Noise is heard or no sound. While playing MP3, noise may occur if the recording is poor. Keep this unit away from mobile phones if the interference is apparent. Turn the volume up. Switch the unit off, check and correct the connection and then switch the unit on. Causes include straining of the speakers through excessive volume or power and using the unit in a hot environment. Humming heard during play. An AC power supply cord or fluorescent light is near the cords. Keep other appliances and cords away from this units cables. A beat sound or noise is heard while receiving radio broadcast. Switch the television or other audio player off or separate it from the unit. Switch the portable audio player off if connected to the EXT-IN AUX port. A low hum or noise is heard during AM broadcast. Keep the antenna away from other cables and cords. Keep the AM antenna away from the unit. The picture on the television near the unit disappears or stripes appear on the screen. The location and orientation of the antenna are incorrect. The television antenna wire is too close to the unit. Separate the antenna wire of the television from the unit. No response when remote control buttons are pressed. Check that the battery is inserted correctly (

4).

[HC55] Open/close sensor The sliding door does not open (or malfunctions). 9) Is the unit turned on?

Is the open/close sensor turned off? (

During CD playback or pause, the CD operation side of the sliding door will not open. The open/close sensor may not react to dark objects. Depending on the lighting, the open/close sensor may malfunction. In this case, try moving the unit to a different place. (Do not place this unit under strong lighting.) When the open/close sensor is on, the sliding door may open/

close while operating the buttons on the top of the unit. In this case, use the remote control. The open/close button lights are flashing. If there is an object close to both open/close sensors, both open/close button lights will flash and the open/close sensor will not function. In this case, move the unit away from the object, or vice versa. (It will take approx. 10 sec. for the unit to check if the clearance is sufficient.) The open/close sensor sound effect cannot be heard when the sliding door opens/closes. This is normal while listening to the radio, during playback, etc. or when linked to a Bluetooth device. 15 Troubleshooting (Continued) iPod/iPhone operations iPod/iPhone does not turn on. Cannot operate with [iPod MENU] button. Verify that the iPod/iPhone battery is not depleted before connecting it to the unit. Before inserting the iPod/iPhone into the dock, turn both the unit and the iPod/iPhone off. Turn the power on and select the appropriate source. No sound is heard from the speakers. The iPod/iPhone is not inserted correctly into the dock. Turn the iPod/iPhone off and remove it from the dock connector. Reinsert it and turn it on again. Make sure that the iPod/iPhone is actually playing something. Adjust the volume. Distorted sound or the sound level is too low. Make sure the equalizer function of the iPod/iPhone is turned off. iPod/iPhone cannot be controlled by the remote control or main unit. Make sure the iPod/iPhone is inserted properly into the dock. Check the dock connection and make sure that iPod/iPhone is selected as the source of music (

12).

ADJUST TIMER Play timer is not set. Adjust the play timer accordingly.

PGM FULL The number of programmed tracks is limited to 24. No further tracks can be programmed.

NO PLAY A CD-ROM disc that is not in CD-DA or MP3 format is inserted. It cannot be played. Check the content. Only MP3 format files can be played.

ERROR Incorrect operation is performed. Read the instructions and try again.

F61 or F76 There is a power supply problem. Consult the dealer.

AUTO OFF The unit has been left unused for about 30 minutes and will shut down in a minute. Press any button to cancel it.

ILLEGAL OPEN Sliding door is not in correct position. Turn the unit off and on again. iPod/iPhone does not charge Check all connections (

5, 12).

[HC55] Bluetooth operations The name of the connected device is shown as . Character that cannot be displayed will be replaced by An unknown device name is detected and displayed as

. Noise is heard or broken sound. The Bluetooth communication distance has exceeded 10 m

(33 ft). Bring the device closer to the unit. There are obstructions between the device and the unit. Remove or avoid the obstacles. Select MODE 1 to improve connection quality (

Interference from mobile phones. 14). Displayed messages The following messages or service numbers appear on the units display when something unusual is detected during startup and use.

--:-- You plugged the AC power supply cord in for the first time or there was a power failure recently. Set the time (

11).

ADJUST CLOCK Clock is not set. Adjust the clock accordingly.

NODEVICE The iPod/iPhone device is not inserted correctly. Read the instructions and try again (

12).

REMOTE 1 The main unit is in REMOTE 1 mode. Switch the remote control to REMOTE 1 mode (

15).

REMOTE 2 The main unit is in REMOTE 2 mode. Switch the remote control to REMOTE 2 mode (

15).

DIMMER Appears 10 seconds after the volume is turned to .

F70 There is a Bluetooth module problem. Disconnect the AC power supply cord and consult your dealer.

NO DISC Insert the disc to be played (

9).

NOT SUPPORTED You have inserted an iPod/iPhone that cannot be played

12).

[HC55]START ERROR Check the iPhone/iPod touch. Visit the below website for more information:

http://radio.vtuner.com/panasonic/en/

UNLOCKED The iPod/iPhone docking switch lever is not locked in position. Make sure that the iPod/iPhone docking switch lever is properly pushed back into place (

12). 16

[HC55]CANNOT SET Select an audio source other than BLUETOOTH or

INTERNET RADIO. Specifications AMPLIFIER SECTION

[HC55] BLUETOOTH SECTION RMS Output Power Stereo mode Front Ch (both ch driven) Total RMS Stereo mode power 40 W FTC Output Power Stereo mode Front Ch (both ch driven) Total FTC Stereo mode power 30 W 20 W per channel (6 ), 1 kHz, 10 % THD 15 W per channel (6 ), 20 Hz to 20 kHz, 10 % THD TUNER SECTION Preset Memory Frequency Modulation (FM) Frequency range Antenna terminals Amplitude Modulation (AM) Frequency range DISC SECTION FM 30 stations AM 15 stations 87.9 MHz to 107.9 MHz

(200 kHz step) 87.5 MHz to 108.0 MHz

(100 kHz step) 75 (unbalanced) 520 kHz to 1710 kHz

(10 kHz step) 522 kHz to 1629 kHz

(9 kHz step) Disc played [8 cm (3") or 12 cm (5")]

CD, CD-R/RW

(CD-DA, MP3 ) Bluetooth system specification V2.1 + EDR Wireless equipment classification Supported profiles Frequency band Driving distance Class 2 (2.5 mW) A2DP, AVRCP, HFP 2402 MHz to 2480 MHz

(Adaptive Frequency Hopping) 10 m (33 ft) Line of Sight

(iPhone 4, at height 1 m

(3.3 ft), in MODE 1) TERMINAL SECTION Phone jack Terminal AUX (Rear) Terminal GENERAL Stereo, 3.5 mm (1/8 ) jack Stereo, 3.5 mm (1/8 ) jack Power consumption Power consumption in standby mode 25 W Power supply Dimensions (W H D) Approx. 0.1 W AC 120 V, 60 Hz With stand 480 mm 194 mm 84 mm

(19" 7 3/4" 3 1/2") Without stand 480 mm 194 mm 69 mm

(19" 7 3/4" 2 3/4") Approx. 2.4 kg (5.3 lbs) 0 C to

( 32 oF to 104 oF) 35 % to 80 % RH

(no condensation) 40 C Pick up Wavelength Laser power Audio Output (Disc) Number of channels MPEG-1 Layer 3, MPEG-2 Layer 3 790 nm For U.S.A. CLASS I For Canada CLASS 1, CLASS 1M FL, FR, 2 ch Mass (Weight) Operating temperature range Operating humidity range Specifications are subject to change without notice. Mass and dimensions are approximate. Total harmonic distortion is measured by a digital spectrum analyzer. SPEAKER SECTION

[HC55]

Type Speaker unit(s) Woofer Tweeter Passive Radiator Impedance

[HC35]

Type Speaker unit(s) Full range Passive Radiator Impedance 2 way, 2 speaker system

(Passive Radiator) 6.5 cm (21/2 ) Cone type 1 per channel 1.5 cm (5/8 ) Piezo type 1 per channel 8 cm (31/8 ) 2 per channel 6 1 way, 1 speaker system

(Passive Radiator) 6.5 cm (21/2 ) Cone type 1 per channel 8 cm (31/8 ) 6 2 per channel 17 Spanish Quick Reference/

Referencia rpida en espaol Conexiones Otras Conexiones Abra la tapa EXT-IN AUX/Tapa para conectar los auriculares o dispositivos de msica externos (por ejemplo, reproductor MP3). Empuje la parte saliente para abrir la tapa Vista superior

. Tapa EXT-IN AUX/

Auriculares Parte saliente Conecte los auriculares (no provistos) Reduzca el volumen y conecte los auriculares. Tipo de enchufe:

3,5 mm (1/8 ) estreo Para evitar daos a la audicin, evite escuchar durante perodos prolongados. La excesiva presin sonora de audfonos y auriculares puede causar prdida de la audicin. Conectar un dispositivo de msica externo

(para modo AUX) Enchufe el cable de audio (no provisto) en el jack EXT-IN AUX . Tipo de enchufe: 3,5 mm (1/8 ) estreo Presione [EXT-IN, RADIO] repetidamente para seleccionar AUX y comience la reproduccin en el dispositivo conectado. Usted puede seleccionar el nivel de sonido de entrada del dispositivo externo.

[HC55]

Presione [SOUND] repetidamente para seleccionar INPUT LEVEL. Presione [

NORMAL.

] para seleccionar HIGH o

[HC35] Presione [INPUT LEVEL] repetidamente para seleccionar HIGH o NORMAL. Apague el ecualizador o baje el volumen del dispositivo externo para reducir la seal de entrada. El nivel alto de la seal de entrada distorsiona el sonido. Para ms detalles, consulte el manual de instrucciones del otro equipo. Los cables y dispositivos no se suministran. Vista posterior Orificios de ventilacin Conexiones bsicas Conecte la antena interior FM. Fije con cinta la antena a un muro o columna en un lugar que tenga la menor cantidad de interferencia. Cinta adhesiva Antena interior FM Conecte la antena de cuadro AM. Mantenga el cable de la antena suelto alejado de otros cables o hilos. Coloque la antena en forma vertical en su base hasta que quede calzada y haga clic. Antena de cuadro AM Conecte el cable de alimentacin AC. Conecte el cable de alimentacin AC despus de que todas las dems conexiones estn completas. Encienda la unidad despus de unos segundos. Consumo de energa en Standby (modo de espera):

Aprox. 0,05 W Hacia el tomacorriente AC 18 Gua de referencia del mando a distancia Mando a distancia Vista frontal

/I]

[2]

[2]

[6]

23, 24) 20) 22) 24) 21) 24) 21) 22) 22) 20, 21) 20, 21, 23, 24) 21)

, iPod] (

], [POWER, 20, 22)

, OPEN/CLOSE]

[SLEEP] (

Interruptor Standby/On

Presione para conmutar la unidad desde el modo On a Standby, o viceversa. En el modo Standby, la unidad sigue consumiendo una pequea cantidad de energa. Botones numricos

[1-9, 0, 10] (

Para seleccionar un nmero de 2 dgitos Por ejemplo 16: [ 10]

[1]

Para seleccionar un nmero de 3 dgitos Por ejemplo 226: [ 10]

[ 10]

[6]

[DEL] (

[HC55] [

24)

[HC35] [iPod] (

[CD] (

22, 23, 24)

[HC55] [

23, 24) 18, 20, 22)

[SOUND] (

[D.BASS] (

22)

[PLAY MENU] (

[iPod MENU] (

[HC55] [ MENU]

[DISPLAY] (

[ DIMMER]

Mantenga presionado para oscurecer el visor. Mantenga presionado nuevamente para cancelar.

[HC55] [OPEN/CLOSE SENSOR] (

[HC35] [INPUT LEVEL] ( 18) Informacin del mando a distancia

[iPod

[iPod

[HC55] Indicador de la actividad del sensor

[PLAY, 22)

[CLOCK/TIMER] (

[PROGRAM] (

[+, VOL ,]

VOLUME +] (

Regula el volumen de sonido.

[MUTE] (

Silencia el sonido. Presione nuevamente para cancelar.

MUTE tambin se cancela cuando se regula el volumen o se apaga la unidad.

[EXT-IN, RADIO]

[RADIO/EXT-IN] (

[HC55] [

[PRESET EQ] (

[RADIO MENU] (

[AUTO OFF]

Esta funcin le permite apagar la unidad (excepto en modo radio) despus de que no se usa durante aproximadamente 30 minutos.

[AUTO PRESET] (

21)

[CD ] (

[CD , OPEN/CLOSE]

[HC55] Indicador de la actividad del sensor Indicador de Standby

[HC55] Sensor Abrir/

Cerrar (

Altavoz Visor Puerta deslizante

[HC55] Micrfono (

[HC55] Indicador de Bluetooth (

Sensor de seal del mando a distancia Distancia:

Aprox. 7 m (23 pies) directamente en el frente.

, 18, 21, 23, 24) 20) 20, 21, 23)

24) 20, 21, 21) 23) 20, 21,

], [OK]

20) 24) 24) 23) 20) 21) 20) 20)

Inserte de forma tal que los polos (

del mando a distancia. y

) concuerden con los Coloque primero este lado adentro. Use bateras alcalinas o de manganeso.

19 Unidad principal Los botones tales como distancia. Se pueden usar indistintamente. Vista superior funcionan igual que el mando a Abrir/Cerrar la puerta deslizante Preparacin Presione [

] para encender la unidad. Abrir la puerta deslizante Para operaciones con discos:

Mientras la puerta deslizante est cerrada, presione [CD ] para abrirla. Para operaciones con iPod/iPhone:

Mientras la puerta deslizante est cerrada, presione [iPod

] para abrirla. Cerrar la puerta deslizante Presione [CD ] o [iPod

] nuevamente. Mantenga los dedos alejados de la puerta deslizante cuando se est cerrando para evitar posibles daos menores. Si fuerza la puerta deslizante para cerrarla, se puede daar. Al extraer el CD, tenga cuidado de no golpear la puerta deslizante. La puerta deslizante no se cerrar si la palanca del interruptor del conector no se coloca en la posicin original.

[HC55] Sensor Apertura/Cierre Con esta funcin, la puerta deslizante se puede abrir sin presionar un botn. La puerta se abrir y cerrar cuando mueva su mano sobre el sensor. Para operaciones con discos:

Mientras la puerta deslizante est cerrada, mueva su mano de a

. Para cerrar la puerta deslizante, mueva su mano de a Para operaciones con iPod/iPhone:

Mientras la puerta deslizante est cerrada, mueva su mano de a

. Para cerrar la puerta deslizante, mueva su mano de a

. Para deshabilitar el sensor de Apertura/Cierre Presione [OPEN/CLOSE SENSOR]. Cada vez que pulsa el botn, el sensor se enciende

ON SENSOR) o apaga (OFF SENSOR). Para agregar un efecto de sonido cuando la puerta deslizante se abre/cierra (cuando se usa el sensor.) Presione [SOUND] repetidamente para seleccionar

BUZZER. Presione [

LOW:

MID:

HIGH:

OFF:

Fije el nivel de sonido bajo. Fije el nivel de sonido medio. Fije el nivel de sonido alto. Apague el efecto de sonido.

] para seleccionar el siguiente ajuste.

] o [

El sensor de apertura/cierre podra activarse accidentalmente si un objeto, la mano, una parte del brazo, animales domsticos o nios se mueven cerca de l. Si el sensor de apertura/cierre no funciona o el rango de reaccin disminuye, abra/

cierre la puerta deslizante usando los botones de la unidad o el mando a distancia. La puerta deslizante no se abrir durante la reproduccin de CD. 20 Operaciones con discos Insertar un disco

] para encender la unidad. izquierda) 1 Presione [

2 Abra la puerta deslizante. (

3 Con la etiqueta del disco volteada hacia usted, incline el disco sobre la bandeja ubicada debajo de la puerta deslizante. 4 Coloque el disco sobre el sujetador central y luego empuje el disco hacia abajo hasta que quede bien calzado y haga clic. 5 Cierre la puerta deslizante. izquierda)

Sacar un disco Abra la puerta deslizante. Sostenga el centro y la parte superior derecha del disco, y tire de la parte superior derecha para separarlo del sujetador. Incline el disco para no tocar la puerta deslizante ni las lentes, y squelo. Reproduccin bsica arriba). 1 Presione [

] para encender la unidad. 2 Inserte el disco que desea reproducir (

3 Presione [CD]. 4 Presione [

Detencin Pausa

]. Presione nuevamente

] para comenzar a reproducir. Presione [

Presione [

para reiniciar la reproduccin. Presione [

pista. Presione [

(MP3) Mantenga presionado [

] para saltear el lbum.

] o [

] o [

] para saltear una

, Saltear Bsqueda ([CD]

solamente) Reproduccin de acceso directo

(La reproduccin inicia en la pista que seleccion.)

[CD]:

Presione los botones numricos para seleccionar la pista.

[MP3]:

] para seleccionar el Presione [

lbum. Presione [

] una vez y luego los botones numricos para seleccionar la pista. Esta funcin no funciona durante la reproduccin aleatoria o programada.

21) Ver la informacin del contenido Presione [DISPLAY] repetidamente durante la reproduccin o la pausa. Se despliega la informacin de la pista actual, etc. Cantidad mxima de caracteres desplegables:

aproximadamente 30 Esta unidad es compatible con etiquetas de la versin 1.0 y 1.1 ID3. Los datos de texto no soportados no se desplegarn. Repetir la reproduccin 20) seleccionar REPEAT. Despus de realizar los pasos 1-3 de Reproduccin bsica (

1 Presione [PLAY MENU] repetidamente para 2 Presione [

3 Presione [

Para detener la repeticin de la reproduccin, seleccione OFF REPEAT en el paso 3.

, presione [OK].

] para comenzar a reproducir.

] para seleccionar ON REPEAT y Funcin de modo de reproduccin 20) Despus de realizar los pasos 1-3 de Reproduccin bsica (

1 Presione [PLAY MENU] repetidamente para 2 Presione [

seleccionar PLAY MODE.

] para seleccionar el modo siguiente

, y presione [OK]. 1-TRACK 1TR:

1-ALBUM 1ALBUM:

([MP3] solamente) RANDOM RND:

1-ALBUM RANDOM 1ALBUM RND:

([MP3] solamente) Reproduce una pista seleccionada del disco. Reproduce un lbum seleccionado del disco.

] para seleccionar el Presione [

lbum. Reproduce un disco en modo aleatorio. Reproduce en modo aleatorio todas las pistas de un lbum seleccionado.

] para seleccionar el Presione [

lbum.

, 3 Presione [

] para comenzar a reproducir. Durante la reproduccin aleatoria, no se puede saltar a la pista anterior. El modo de reproduccin actual se cancela cuando usted abre la puerta deslizante. Para repetir la reproduccin programada o el modo de reproduccin seleccionado, seleccione ON REPEAT en PLAY MENU. (

20) Reproduccin programada Le permite programar hasta 24 pistas. Despus de realizar los pasos 1-3 de Reproduccin bsica (

1 Presione [PROGRAM] durante el modo de detencin. 2 [CD]:

Presione los botones numricos para seleccionar la pista. 20) Para programar ms pistas, siga pulsando los botones numricos.

[MP3]:

] para seleccionar el lbum.

] una vez y luego los botones numricos Presione [

Presione [

para seleccionar la pista. Presione [OK]. Para programar ms pistas, repita los pasos

3 Presione [

Cancelar el modo de programacin Verificar el contenido del programa Borrar la ltima pista programada Borrar todas las pistas programadas

] para comenzar a reproducir. Presione [PROGRAM] en el modo de detencin para cancelar el indicador PGM del visor. Presione [

visualiza en el modo de detencin. Presione [DEL] en el modo de detencin.

] cuando PGM se

] o [

Presione [

Presione [

parpadea CLR ALL.

] en el modo de detencin.

] nuevamente mientras La memoria del programa se borra cuando abre la puerta deslizante. Operaciones con la radio Sintonizacin manual 1 Presione [EXT-IN, RADIO] repetidamente para 2 Presione [

seleccionar FM o AM.

] para seleccionar la frecuencia

] o [

de la estacin requerida.

ST se visualiza cuando se est recibiendo de una emisora FM estreo. Para sintonizar automticamente, mantenga presionado [

] o

] hasta que la frecuencia comience a cambiar rpidamente.

] nuevamente. Para cancelar la sintonizacin automtica, presione [

La sintonizacin automtica puede no funcionar cuando hay exceso de interferencia.

] o Para mejorar la calidad del sonido FM Presione [RADIO MENU] mientras recibe emisoras FM. Presione [

Presione [

] para seleccionar FM MODE.

] para seleccionar MONO.

, para volver a las emisoras estreo. Seleccione STEREO en el paso

MONO tambin se cancela si se cambia la frecuencia. Para mejorar la calidad de sonido AM Presione [RADIO MENU] para seleccionar B.PROOF mientras recibe transmisiones AM. Presione [

, presione [OK].

] para seleccionar la prueba beat (BP 1 o BP 2) y Este ajuste se restaura a BP 1 cuando se realizan cambios (por ejemplo, se cambia la frecuencia). Predefinicin de memoria Usted puede predefinir hasta 30 canales FM y 15 canales AM. Preparacin Presione [EXT-IN, RADIO] repetidamente para seleccionar FM o AM. Predefinicin automtica Presione [OK] para conmutar la frecuencia entre LOWEST y CURRENT. Presione [AUTO PRESET].

PGM comienza a destellar y la radio comienza a predefinir todas las estaciones que puede recibir en los canales, en orden ascendente.

] o [

Predefinicin manual Presione [

Presione [PROGRAM]. Mientras PGM destella, presione los botones numricos para seleccionar un canal.

] para sintonizar la estacin requerida. La estacin que ocupa un canal se borra si otra estacin se predefine en ese canal. Para predefinir ms estaciones, repita el paso

. Seleccionar una estacin predefinida

] para seleccionar el canal.

] o [

Presione [

Alternativamente, presione los botones numricos para seleccionar el canal. Definicin de asignacin FM/AM Esta unidad se define en fbrica como FM 0,2 MHz y AM 10 kHz, pero puede cambiar estos ajustes para recibir emisoras asignadas en el paso FM 0,1 MHz o AM 9 kHz. Presione [EXT-IN, RADIO] para seleccionar FM. Seleccione AM para cambiar a los pasos de frecuencia AM. Mantenga presionado [RADIO/EXT-IN] en la unidad principal. Despus de unos segundos, el visor cambia y muestra la frecuencia mnima actual. Contine manteniendo pulsando [RADIO/EXT-IN] en la unidad principal. Cuando la frecuencia mnima actual cambia, suelte el botn. Para volver al paso original, repita los pasos Despus de que se cambia la definicin, se borrar cualquier frecuencia previa. a

. 21 Ajuste de sonido Se pueden agregar los siguientes efectos de sonido a la salida de audio. EQ predeterminado Presione [PRESET EQ] repetidamente para seleccionar HEAVY, SOFT, CLEAR,

VOCAL o FLAT. Bajos o agudos Sonido Surround

] para graduar el nivel (-4 Presione [SOUND] repetidamente para seleccionar BASS o TREBLE. Presione [

a +4). Presione [SOUND] repetidamente para seleccionar SURROUND. Presione [

ON SURROUND.

] para seleccionar

, Para cancelar el sonido surround, seleccione

OFF SURROUND en el paso Si la interferencia en la recepcin de FM estreo aumenta, cancele el efecto de sonido surround. D.Bass Presione [D.BASS] durante la reproduccin para seleccionar ON D.BASS o OFF D.BASS. Puede experimentar una reduccin de la calidad del sonido cuando se usan estos efectos con algunas fuentes. Si esto sucede, desactive los efectos de sonido. Sincronizador Ajuste del reloj ste es un reloj de 12 horas. 1 Presione [CLOCK/TIMER] para seleccionar 2 En 10 segundos, presione [

3 Presione [OK].

CLOCK.

] para fijar la hora.

, Para visualizar el reloj, presione [CLOCK/TIMER]. Vuelva a fijar el reloj regularmente para mantener la precisin. Sincronizador de reproduccin Usted puede fijar el sincronizador para que se active a una hora determinada para despertarlo. Esta unidad ofrece 3 sincronizadores opcionales de reproduccin. Preparacin arriba). seleccionar PLAY 1, PLAY 2 o PLAY 3. Encienda la unidad y fije el reloj (

Prepare la fuente musical (disco, radio, iPod/iPhone o AUX) y fije el volumen. 1 Presione [CLOCK/TIMER] repetidamente para 2 En 10 segundos, presione [

hora de inicio. 3 Presione [OK]. 4 Fije la hora de finalizacin repitiendo los pasos

] para fijar la

, 2 y 3. Para activar el sincronizador el sincronizador de reproduccin deseado.

] repetidamente para activar

] para apagar la unidad. Presione [CLOCK/TIMER] dos veces.

(Se visualiza la definicin.) 5 Presione [PLAY, 6 Presione [

Verificar las definiciones

(Cuando la unidad est encendida o en modo standby) Cancelar Presione [PLAY, el indicador del sincronizador del visor.

] dos veces para cancelar El sincronizador comenzar a la hora predefinida y el volumen aumentar gradualmente hasta el nivel predefinido. Apagado automtico El apagado automtico puede apagar la unidad despus de una hora predefinida. Presione [SLEEP] para activar o desactivar la funcin de apagado automtico. 120MIN 30MIN 60MIN 90MIN OFF (Cancelar) Presione [SLEEP] una vez para verificar el tiempo restante. 22 El sincronizador de reproduccin y el apagado automtico se pueden usar juntos. El apagado automtico siempre tiene prioridad. Asegrese de no superponer los ajustes del sincronizador. Cuando AUTO OFF est en ON y la unidad se deja sin usar durante aproximadamente 30 minutos, la unidad se apagar aun cuando no haya expirado el tiempo de reproduccin o el de apagado automtico. Escuchar audio de un iPod o iPhone Insertar/Extraer un iPod/iPhone Insertar un iPod/iPhone 1 Abra la puerta deslizante. (

2 Inserte el adaptador del conector apropiado (no 20) provisto) para el iPod/iPhone. Inserte el lado del adaptador del conector del iPod/iPhone con los clips enfrentados hacia usted primero y luego empuje el lado opuesto hasta que quede bien calzado y haga clic. Clips Adaptador del conector Palanca del interruptor de acoplamiento del iPod/iPhone Conector Clic!

Clic!

3 Presione [

] para desbloquear el puerto de iPodR/iPhone y luego tire de la palanca del interruptor del puerto para inclinar el puerto de iPodR/iPhone. 4 Conecte el iPod/iPhone (no provisto) firmemente. 5 Empuje la palanca del interruptor del puerto hasta que haga clic en su sitio. 6 Cierre la puerta deslizante. Asegrese de sacar el iPod/iPhone del estuche. 20)

Extraer el iPod/iPhone Repita los pasos 1 y 3 (

Para extraer, simplemente tire del iPod/iPhone hacia afuera. Repita los pasos 5 y 6 (

arriba). arriba). El conector del iPod/iPhone se puede daar si no est inclinado cuando se conecta o desconecta el iPod/iPhone. Asegrese de usar un adaptador del conector que sea compatible con su iPod/iPhone. Para comprar un adaptador del conector, consulte al distribuidor de iPod/iPhone. Reduzca el volumen de la unidad principal al mnimo antes de conectar o desconectar el iPod/iPhone. Operaciones con el iPod Preparacin Presione [iPod] ([HC55]: [

seleccionar IPOD. Reproducir Pausa Saltear pista Buscar la pista actual Visualizar el men iPod/

iPhone/volver al men anterior Seleccione los contenidos en el men iPod/iPhone

, iPod]) repetidamente para

] o [

] o [

]. Presione Presione [

Presione [

nuevamente para reiniciar la reproduccin. Presione [

Mantenga presionado [

Presione [iPod MENU] en modo de reproduccin. (Mando a distancia solamente) Presione [

] y luego [OK].

(Mando a distancia solamente)

] o

, iPod/iPhone compatibles (a junio de 2011) La compatibilidad depende de la versin de software de su iPod/

iPhone. Nombre iPod touch 4ta generacin iPod nano 6ta generacin iPod touch 3ra generacin iPod nano 5ta generacin (videocmara) iPod touch 2da generacin iPod classic iPod nano 4ta generacin (video) iPod classic iPod touch 1ra generacin iPod nano 3ra generacin (video) iPod classic iPod nano 2da generacin (aluminio) iPod 5ta generacin (video) iPod 5ta generacin (video) iPod nano 1ra generacin iPhone 4 iPhone 3GS iPhone 3G iPhone Capacidad de memoria 8 GB, 32 GB, 64 GB 8 GB, 16 GB 32 GB, 64 GB 8 GB, 16 GB 8 GB, 16 GB, 32 GB 120 GB, 160 GB (2009) 8 GB, 16 GB 160 GB (2007) 8 GB, 16 GB, 32 GB 4 GB, 8 GB 80 GB 2 GB, 4 GB, 8 GB 60 GB, 80 GB 30 GB 1 GB, 2 GB, 4 GB 16 GB, 32 GB 8 GB, 16 GB, 32 GB 8 GB, 16 GB 4 GB, 8 GB, 16 GB Segn el modelo, puede ser necesario extraer el iPod/iPhone y seleccionar el lbum, artista, etc. en l.

[HC55] Escuchar radio por Internet Esta unidad puede reproducir radio por Internet si est instalado

vTuner for Panasonic en su iPhone/iPod touch. Visite el sitio web que se indica a continuacin para obtener ms informacin sobre vTuner for Panasonic:

http://radio.vtuner.com/panasonic/en/

(Modelos de iPhone/iPod touch sensibles al tacto y versiones de software compatibles, compra, instalacin y funcionamiento.) Preparacin Instale vTuner for Panasonic en su iPhone/iPod touch. 1 Inserte el iPhone/iPod touch en la unidad. 2 Presione [

, iPod] repetidamente para seleccionar INTERNET RADIO. Se iniciar vTuner for Panasonic. 23 Para usar estas funciones, el dispositivo Bluetooth debe soportar AVRCP

(Audio Video Remote Control Profile). Esta unidad no puede transmitir datos al dispositivo Bluetooth. Cuando reproduce contenido del iPod/iPhone a travs del Bluetooth con la unidad principal, se puede sentir un sonido intermitente si deja la pantalla del men iPod/iPhone Bluetooth activa o cuando registra o conecta el Bluetooth. Si esto ocurre, salga de la pantalla del men iPod/iPhone Bluetooth. Cuando reproduce msica del iPod/iPhone a travs de una conexin Bluetooth y el iPod/iPhone est conectado al conector de iPod/iPhone de esta unidad, el audio no ser reproducido mientras est seleccionado

BLUETOOTH. Seleccione IPOD para seguir escuchando la msica. Hands-Free Profile (HFP) Esta unidad funciona como un Bluetooth manos libres para su telfono mvil. Para responder una llamada (IN CALL parpadea) Para cancelar una llamada Para ajustar el volumen del sonido Para silenciar el micrfono

]. CALLING comienza a Presione [

parpadear en el visor (hable en el micrfono de la unidad). Presione [

] nuevamente para transferir la llamada al telfono mvil (TRANSFER parpadea. Ahora puede conversar usando el telfono mvil). Presione [

]. Presione [+, VOL ,] (regulable de

TEL VOL 1 a TEL VOL 10). Presione [MUTE]. Presione nuevamente para cancelar.

(Durante MIC MUTE, la persona que llama no puede escuchar su voz). Esta unidad no funciona con Headset Profile (HSP). Cuando el telfono mvil est demasiado cerca del micrfono de esta unidad, se puede escuchar ruido. Cuando hace una llamada mantenga siempre el telfono alejado del micrfono de esta unidad. El audio de un disco se detendr cuando llama en modo manos libres. Desconectar el dispositivo Bluetooth 1 Presione [

2 Presione [ MENU] para visualizar seleccionar BLUETOOTH.

, iPod] repetidamente para

DISCONNECT? y luego presione [OK]. Se visualizar un mensaje de confirmacin. 3 Presione [

] para seleccionar YES y luego presione [OK]. La conexin tambin se puede detener cuando desactiva la transmisin Bluetooth en el dispositivo Bluetooth conectado.

[HC55] Uso de un dispositivo compatible con Bluetooth Operaciones con Bluetooth Preparacin Sincronice el dispositivo Bluetooth a esta unidad para crear una conexin de audio. 1 Presione [

, iPod] repetidamente para seleccionar BLUETOOTH. Cuando lo usa por primera vez, entra automticamente en el modo de sincronizacin. 2 Mientras la unidad est en modo de sincronizacin, acceda al men del dispositivo Bluetooth y ejecute la bsqueda de Bluetooth para encontrar esta unidad (SC-HC55). Consulte el manual del usuario del dispositivo Bluetooth para conocer ms detalles sobre cmo conectar un dispositivo Bluetooth. Si se le solicita la clave, ingrese 0000. 3 Si la sincronizacin es satisfactoria, se visualizar el nombre del dispositivo sincronizado durante 2 segundos. Se encender el indicador de Bluetooth. La unidad ahora est lista para usarse con el dispositivo Bluetooth. Asegrese de que el dispositivo Bluetooth soporte A2DP (Advance Audio Distribution Profile). Esta unidad soporta la recepcin A2DP que est protegida por derechos de autor mediante el mtodo SCMS-T. A2DP le permite reproducir sonido estreo desde una fuente de audio

(telfono mvil, PC o laptop) en esta unidad a travs del Bluetooth. Segn la especificacin o la configuracin del telfono mvil, la conexin puede no establecerse o el funcionamiento y la visualizacin pueden variar. Si registra ms de la cantidad mxima de dispositivos, se sobregrabar el dispositivo ms viejo en la historia de conexiones. Si un dispositivo ya registrado se vuelve a registrar, se sobregrabar. Reproduccin bsica Sincronice el dispositivo Bluetooth a esta unidad para crear una conexin de audio. 1 Presione [

2 En el dispositivo Bluetooth:

seleccionar BLUETOOTH.

, iPod] repetidamente para Seleccione esta unidad (SC-HC55) en la pantalla de configuracin Bluetooth para hacer esta conexin. 3 En el dispositivo Bluetooth:

Comience a reproducir msica de una fuente Si el dispositivo est conectado, la msica se escuchar en esta unidad. El indicador de Bluetooth se enciende cuando hay una conexin. Si es necesario, consulte el manual del usuario del dispositivo Bluetooth. 4 Tambin puede realizar los siguientes controles con el mando a distancia. Reproducir Detencin Pausa Saltear pista Visualizar informacin 24

] para comenzar a reproducir.

Presione [

Presione [

Presione [

reiniciar la reproduccin. Presione [

]. Presione [DISPLAY] repetidamente.

] o [

]. Presione nuevamente para 25 Limited Warranty

(ONLY FOR U.S.A. AND PUERTO RICO) Panasonic Consumer Electronics Company, Division of Panasonic Corporation of North America One Panasonic Way, Secaucus, New Jersey 07094 Panasonic Home Audio Products Limited Warranty Limited Warranty Coverage

(For USA and Puerto Rico Only) If your product does not work properly because of a defect in materials or workmanship, Panasonic Consumer Electronics Company (referred to as the warrantor) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (warranty period), at its option either

(a) repair your product with new or refurbished parts, (b) replace it with a new or a refurbished equivalent value product, or (c) refund your purchase price. The decision to repair, replace or refund will be made by the warrantor. Product or Part Name Audio Products

(except items below) DVD Home Theater System Home Theater Audio System USB Reader-writer, PC Card Adapters

(defective exchange) Accessories: Headphones, cartridges, Microphones, Adapters Rechargeable Batteries, DVD-RAM Disc

(defective exchange) SD Memory Cards, Rechargeable Battery Packs (defective exchange) 1 year 1 year Not Applicable Not Applicable Not Applicable 1 year 1 year 1 year Labor 1 year Parts 1 year 90 days 90 days 10 days 90 days During the Labor warranty period there will be no charge for labor. During the

Parts warranty period, there will be no charge for parts. This Limited Warranty excludes both parts and labor for non-rechargeable batteries, antennas, and cosmetic parts (cabinet). This warranty only applies to products purchased and serviced in the United States or Puerto Rico. This warranty is extended only to the original purchaser of a new product which was not sold as is. Carry-In or Mail-In Service To find a service center please visit http://www.panasonic.com/help or call 1-800-211-PANA (7262). When shipping the unit, carefully pack, include all accessories, and send it prepaid, adequately insured and preferably in the original carton. When shipping Lithium Ion batteries please visit our Web Site at www.panasonic.com/BatteryHandling as Panasonic is committed to providing the most up to date information. Include a letter detailing the complaint, a return address and provide a daytime phone number where you can be reached. A valid registered receipt is required under the Limited Warranty. IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE PURCHASER WILL BE REQUIRED TO FURNISH A SALES RECEIPT/

PROOF OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE. Limited Warranty Limits And Exclusions This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, introduction of sand, humidity or liquids, commercial use such as hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than a Factory Service Center or other Authorized Servicer, or damage that is attributable to acts of God. 26 THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER LIMITED WARRANTY COVERAGE. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY.

(As examples, this excludes damages for lost time, travel to and from the servicer, loss of or damage to media or images, data or other memory or recorded content. The items listed are not exclusive, but for illustration only.) ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. If a problem with this product develops during or after the warranty period, you may contact your dealer or Service Center. If the problem is not handled to your satisfaction, then write to the warrantors Consumer Affairs Department at the addresses listed for the warrantor. PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOUR RESPONSIBILITY. Customer Services Directory (United States and Puerto Rico) Obtain Product Information and Operating Assistance;

locate your nearest Dealer or Service Center; purchase Parts and Accessories; or make Customer Service and Literature requests by visiting our Web Site at:

http://www.panasonic.com/help or, contact us via the web at:

http://www.panasonic.com/contactinfo You may also contact us directly at:

1-800-211-PANA (7262) Monday-Friday 9am-9pm, Saturday-Sunday 10am-7pm EST For hearing or speech impaired TTY users, TTY:

1-877-833-8855 Accessory Purchases (United States and Puerto Rico) Purchase Parts, Accessories and Instruction Books online for all Panasonic Products by visiting our Web Site at:

http://www.pstc.panasonic.com Or, send your request by E-mail to:

npcparts@us.panasonic.com You may also contact us directly at:

1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only)

(Monday-Friday 9am-9pm EST) Panasonic Service and Technology Company 20421 84th Avenue South, Kent, WA 98032

(We accept Visa, MasterCard, Discover Card, American Express, and Personal Checks) For hearing or speech impaired TTY users, TTY:

1-866-605-1277 As of December 2010 Limited Warranty (ONLY FOR CANADA) Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 PANASONIC PRODUCT - LIMITED WARRANTY EXCHANGE PROGRAM Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship under normal use and for a period as stated below from the date of original purchase agrees to, at its option either (a) repair your product with new or refurbished parts, (b) replace it with a new or a refurbished equivalent value product, or (c) refund your purchase price. The decision to repair, replace or refund will be made by Panasonic Canada Inc. Panasonic Portable / Clock Radio (without Tape, CD, MD) Panasonic Audio Product Panasonic DVD Product Accessories including rechargeable batteries One (1) year One (1) year One (1) year Ninety (90) days This warranty is given only to the original purchaser, or the person for whom it was purchased as a gift, of a Panasonic brand product mentioned above sold by an authorized Panasonic dealer in Canada and purchased and used in Canada, which product was not sold as is, and which product was delivered to you in new condition in the original packaging. IN ORDER TO BE ELIGIBLE TO RECEIVE WARRANTY SERVICE HEREUNDER, A PURCHASE RECEIPT OR OTHER PROOF OF DATE OF ORIGINAL PURCHASE, SHOWING AMOUNT PAID AND PLACE OF PURCHASE IS REQUIRED LIMITATIONS AND EXCLUSIONS This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by Panasonic Canada Inc., or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, introduction of sand, humidity or liquids, commercial use such as hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than an Authorized Servicer, or damage that is attributable to acts of God. Dry cell batteries are also excluded from coverage under this warranty. THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY. (As examples, this warranty excludes damages for lost time, travel to and from the Authorized Servicer, loss of or damage to media or images, data or other memory or recorded content. This list of items is not exhaustive, but for illustration only.) In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the exclusion of implied warranties, so the above limitations and exclusions may not be applicable. This warranty gives you specific legal rights and you may have other rights which vary depending on your province or territory. CONTACT INFORMATION For product information and operation assistance, please contact:

Our Customer Care Centre:

Telephone #:

Fax #:

Email link:

1-800-561-5505

(905) 238-2360

Support contact us email on www.panasonic.ca For defective product exchange within the warranty period, please contact the original dealer or our Customer Care Centre. 27

[HC35]

THE FOLLOWING APPLIES ONLY IN THE U.S.A. FCC Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any unauthorized changes or modifications to this equipment would void the users authority to operate this device. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party:

Panasonic Corporation of North America One Panasonic Way Secaucus, NJ 07094 Support Contact:

Panasonic Consumer Electronics Company Telephone No.: 1-800-211-PANA (7262)

[HC55]

THE FOLLOWING APPLIES ONLY IN THE U.S.A. FCC Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC caution: To maintain compliance with FCC regulations, shielded interface cables must be used with this equipment. Operation with non-

approved equipment or unshielded cables may result in interference to radio and TV reception. Any changes or modifications not approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party:

Panasonic Corporation of North America One Panasonic Way Secaucus, NJ 07094 Support Contact:

Panasonic Consumer Electronics Company Telephone No.: 1-800-211-PANA (7262) WARNING:

To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 20 cm (77/8 ) or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter.

For U.S.A. and Puerto Rico Panasonic Consumer Electronics Company, Division of Panasonic Corporation of North America One Panasonic Way, Secaucus, New Jersey 07094 http://www.panasonic.com For Canada Panasonic Canada Inc. 5770 Ambler Drive Mississauga, Ontario L4W 2T3 www.panasonic.ca Panasonic Corporation 2011 Printed in Malaysia RQTX1260-P F0111MT0