FCC ID: 2ADM5-ET-0011-27 RC GESTURE CONTROL ROBOT

Date: 27 AUG 2020 Product: ET-0011-Gesture Control Battle Robot Size : 420 x 110 mm Instruction Manual Thank you for purchasing the Gesture Control Battle Robot. This manual provides more information about this product, please read the instructions before using. 8+

Product Overview Package Contents Operate Your Robot Note: To avoid losing control, always pay attention when playing the Gesture Control Battle Robot. Gesture Control Battle Robot x 1 Gesture Remote Control x 1 Instruction Manual x 1 Specifications Gesture Remote Control Instruction Manual Gesture Control Battle Robot Power Supply:

4 x AAA 1.5V Batteries

(Alkaline type preferred, not included) Gesture Remote Control Power Supply:

3 x AAA 1.5V Batteries

(Alkaline type preferred, not included) Frequency: 27.145 MHz Gesture Control Battle Robot Instruction Manual Gesture Control Battle Robot Power On/Off Gesture Remote Control On/Off Right Punch Hold the right Gesture Remote Control and punch Left Punch Hold the left Gesture Remote Control and punch How To Play

"Target Practice" board

"Do Not Pass" block Operate Gesture Control Battle Robot to hit the

"Target Practice" board to count the score You can also create more

"Target Practice" board by yourself Power On/Off Slide the ON/OFF Switch to ON to turn on the Gesture Control Battle Robot. Slide the ON/OFF Switch to OFF to turn off the Gesture Control Battle Robot. Power On/Off Slide the ON/OFF Switch to ON to turn on the Gesture Remote Control. Slide the ON/OFF Switch to OFF to turn off the Gesture Remote Control. Back of the insert card Follow the dashed line to cut out the "Target Practice" board & "Do Not Pass" block. Battle with other Gesture Control Battle Robot and avoid crossing the"Do Not Pass" block

*Other Gesture Control Battle Robot sold separately Batteries Installation-Car Batteries Installation-Remote Control Performance Tips Warning FCC Statement 1. Do not control the Gesture Control Battle Robot on grass, sand or go through water. 2. Do not control the Gesture Control Battle Robot in windy or rainy weather. 3. Do not control the Gesture Control Battle Robot into any sharp object. 4. Keep fingers, hair and loose clothing away from Gesture Control Battle Robot. Care and Maintenance Always use dry and soft cloth to clean this product. Avoid this product from being exposed to sunlight or heat. This product is suitable to be used by people who has operating experience in remote toy or aged no less than 8 years old. Please do not put the product in your mouth to prevent choking hazard of small parts. Please do not put the finger into available interspaces. Please do not play the product in a brutal way such as throwing, crashing or twisting it. Please store the smaller-sized product accessories in places that are out of reach of children, in order to avoid the occurrence of accidents. Avoid immersing these toys in water, otherwise, the electronic parts may be damaged. Avoid placing the batteries in places in high temperatures and avoid exposure to heat. Check the product regularly. If any damages are discovered, please stop using immediately, until it is completely repaired in good working condition. IMPORTANT: BATTERY INFORMATION CAUTION:

1. TO AVOID BATTERY LEAKAGE a. Always follow the instructions carefully. Use only batteries specified and be sure to insert them correctly by matching the + and - polarity markings. b. Do not mix old batteries and new batteries or standard (carbon-zinc) with alkaline batteries. c. Remove exhausted or dead batteries from the product. d. Remove batteries if product is not to be played with for a long time. e. Do not short-circuit the supply terminals. 2. Should this product cause, or be affected by local electrical interference, move it away from other electrical equipment. Reset (switching ON & OFF again or removing and re-inserting batteries) if necessary. When young children are operating the product, it shall be ensured that the adults are guiding and making sure the product control is within the viewing range of the controller (or instructor) so that it makes the control of the toy more convenient. When the product is not in use, please switch off the power supplies of the toy, and remove the batteries from the product. Please note that we wont take any responsibility for any wrong operation as this may result in severe injury or loss of property, and we cannot control the operating process during the time when the user assembles or uses this product. Once this product is sold, we wont be responsible for any safety responsibility during the time the user operates or uses controls this products. This device complies with the part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that Consult the dealer or experienced radio/ TV technician for help. RF warning statement:

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. to which the receiver is connected. FCC ID: 2ADM5-ET-0011-27 Item# ET-0011 Keep All Relevant Information for Future Reference Made in China To install batteries into the Gesture Control Battle Robot, unscrew the screw on the battery box cover to open the battery compartment. Insert 4 x AAA 1.5V batteries (Not Included) into the battery box. Batteries should be placed as shown in the diagram. Put back in place the battery box cover and tighten the screw. To install batteries into the Gesture Remote Control, unscrew the screw on the battery box cover to open the battery compartment. Insert 3 x AAA 1.5V batteries (Not Included) into the battery box. Batteries should be placed as shown on the diagram. Put back in place the battery box cover and tighten the screw. Notice:

When placing the batteries, you must insert according to the correct polarity, the Gesture Control Battle Robot wont function if batteries are reversed. Notice:

When placing the batteries, you must insert according to the correct polarity, the Gesture Remote Control wont function if batteries are reversed.

Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200901830-RF EXHIBIT A - FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Zeeva International Limited Suite 1007B, 10th Floor, Exchange Tower, 33 Wang Chiu Road, Kowloon Bay, Hong Kong Tel: +852-2868 0511 | Fax: +852-2524 1986 E-mail: akshay.butani@zeeva.com 10/29/2020 FCC Authorization FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

We, Zeeva International Limited the undersigned, hereby authorize Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratory Corporation on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature:

Printed Name: Akshay P Butani Title: Vice President

Technical Description ET-0011 use MCUTX IC for remote control and 27.145MHz crystal oscillator as the modulating and amplifying circuit.When the function button is pressed, Two set of binary serial codes (1KHZ/250Hz) are generated by IC code. The coded signal (square wave 1KHZ/250Hz) is loaded into the carrier by the modulation circuit, amplified by the amplifier circuit and transmitted by the antenna. Frequency 27.145MHz